1、BS EN ISO 1401:2016Rubber hoses for agricultural spraying (ISO 1401:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 1401:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 1401:2016. It supersedes BS EN ISO 1
2、401:2000 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport
3、to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 89072 7 ICS 23.040.70; 65.060.25; 65.060.40; 83.140.40 Compliance with a British Standard cannot conf
4、er immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1401 Novemb
5、er 2016 ICS 83.140.40; 65.060.40; 65.060.25 Supersedes EN ISO 1401:1999English Version Rubber hoses for agricultural spraying (ISO 1401:2016) Tuyaux en caoutchouc pour pulvrisation agricole (ISO 1401:2016) Gummischluche zum Sprhen in der Landwirtschaft (ISO 1401:2016) This European Standard was appr
6、oved by CEN on 9 October 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
7、 standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language
8、and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hun
9、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CEN
10、ELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1401:2016 EBS EN ISO 1401:2016EN ISO 1401:2016 (E) 3 European foreword This document (EN ISO 1401:2016) has been pre
11、pared by Technical Committee ISO/TC 45 “Rubber and rubber products“ in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publica
12、tion of an identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be withdrawn at the latest by May 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not
13、be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1401:1999. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
14、Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey a
15、nd the United Kingdom. Endorsement notice The text of ISO 1401:2016 has been approved by CEN as EN ISO 1401:2016 without any modification. BS EN ISO 1401:2016ISO 1401:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Classification 15 Construction and materials . 26 D
16、imensions and tolerances . 26.1 Nominal bore and inside diameter 26.2 Length . 26.3 Minimum thickness of lining and cover 26.3.1 Types A and B . 26.3.2 Type C 27 Physical requirements on samples taken from the hose or from moulded sheets of equivalent vulcanization 27.1 Tensile strength and elongati
17、on at break of rubber lining and cover . 27.2 Requirements after immersion in fluid . 37.3 Accelerated ageing . 38 Physical requirements on finished hoses . 38.1 Change in dimensions . 38.2 Hydrostatic requirements . 38.2.1 Hydrostatic pressure 38.2.2 Hydrostatic testing after ageing in liquid . 48.
18、3 Bending test requirements . 48.4 Adhesion . 48.5 Resistance to ozone . 49 Frequency of testing 410 Type testing 411 Test report or certificate 412 Marking 4Annex A (normative) Type tests and routine tests 6Annex B (informative) Productions acceptance tests . 7Bibliography 8 ISO 2016 All rights res
19、erved iiiContents PageBS EN ISO 1401:2016ISO 1401:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees
20、. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Intern
21、ational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the diffe
22、rent types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall
23、 not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is
24、information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technica
25、l Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This third edition cancels and replaces the second edition (ISO 1401:1
26、999), which has been technically revised.The main changes are the following: the word “agropharmaceutical” has been replaced with “agricultural chemicals”; Clause 2 has been updated: ISO 471 and ISO 1746 have been deleted and replaced by ISO 23529 and ISO 10619-1; 7.2 has been amended to update the
27、test requirements; Clauses 9 and 10, describing frequency of testing, routine tests, type tests and production acceptance tests, have been added; Clause 8 has been renumbered as Clause 12: Marking b) and e) has been amended; Annexes A and B have been introduced in accordance with ISO/TC 45/SC 1 guid
28、e 976-rev. 7:2013; Clause 11, describing a test report or certificate supplied on request of purchaser, has been added.iv ISO 2016 All rights reservedBS EN ISO 1401:2016INTERNATIONAL STANDARD ISO 1401:2016(E)Rubber hoses for agricultural spraying1 ScopeThis document specifies requirements for three
29、types of flexible rubber hose for pressure spraying of agricultural chemicals and/or fertilizer products within a temperature range of 10 C to +60 C.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of t
30、his document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain propertiesISO 188, Rubber, vulcanized or the
31、rmoplastic Accelerated ageing and heat resistance testsISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1817, Rubber, vulcanized or thermoplastic D
32、etermination of the effect of liquidsISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assembliesISO 7326:2006, Rubber and plastics hoses Assessment of ozone resistance under static conditionsISO 8033, Rubber and plastic
33、s hoses Determination of adhesion between componentsISO 10619-1, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8330 apply. ISO
34、and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp4 ClassificationThree types of hose are specified as follows: Type A: Maximum wo
35、rking pressure of 1,0 MPa (10 bar); Type B: Maximum working pressure of 4,0 MPa (40 bar); Type C: Maximum working pressure of 6,0 MPa (60 bar). ISO 2016 All rights reserved 1BS EN ISO 1401:2016ISO 1401:2016(E)5 Construction and materialsThe hose shall consist of the following: a synthetic rubber lin
36、ing; a reinforcement of one or more layers of textile fibres; a cover of natural or synthetic rubber.6 Dimensions and tolerances6.1 Nominal bore and inside diameterThe dimensions of the hose shall be in accordance with the inside diameter and tolerances given in Table 1.Table 1 Nominal bores, diamet
37、ers and tolerancesNominal bore diameterInside diameter mmTolerance mm6,3 6,30 0,758 8,00 0,7510 10,00 0,7512,5 12,50 0,7516 16,00 0,7520 20,00 0,7525 25,00 1,256.2 LengthThe tolerance on lengths shall be as specified in ISO 1307.6.3 Minimum thickness of lining and cover6.3.1 Types A and BWhen tested
38、 in accordance with ISO 4671, the lining shall have a minimum thickness of 1,6 mm and the cover shall have a minimum thickness of 1,0 mm.6.3.2 Type CWhen tested in accordance with ISO 4671, the lining shall have a minimum thickness of 2,0 mm and the cover shall have a minimum thickness of 1,6 mm.7 P
39、hysical requirements on samples taken from the hose or from moulded sheets of equivalent vulcanization7.1 Tensile strength and elongation at break of rubber lining and coverWhen determined in accordance with ISO 37, the tensile strength and elongation at break shall be no less than the values given
40、in Table 2.2 ISO 2016 All rights reservedBS EN ISO 1401:2016ISO 1401:2016(E)Table 2 Tensile strength and elongation at breakHose componentTensile strength MPaElongation at break %Lining 7,0 200Cover 7,0 2507.2 Requirements after immersion in fluidWhen tested in accordance with ISO 1817, after immers
41、ion for 72 h 2 h in the actual liquid which the hose will convey during service in purchasers system, at standard laboratory temperature (see ISO 23529), the lining and cover shall conform to the values given in Table 3.The specification of the test liquid shall be obtained from the purchaser by the
42、 hose manufacturer (or dealer), alternatively a sample of sufficient quantity to carry out the test shall be obtained from the client. Each test shall be carried out with a new sample of test liquid which has not been stored past its product tenability date.Table 3 Requirements after immersion in te
43、st liquidProperty RequirementVolume Maximum increase 55 %Tensile strength Maximum reduction 50 %Elongation at break Maximum reduction 40 %7.3 Accelerated ageingFor liner and cover, after ageing the sample in air for 72 2 h at 100 C 2 C, as specified in ISO 188, the tensile strength and elongation at
44、 break as determined by ISO 37 shall decrease by no more than 25 % and 50 % respectively from their initial values.8 Physical requirements on finished hoses8.1 Change in dimensionsWhen the hose is tested at proof pressure in accordance with ISO 1402, the changes in outside diameter and length shall
45、be no greater than 7 % and there shall be no leaks or other signs of damage.8.2 Hydrostatic requirements8.2.1 Hydrostatic pressureWhen tested in accordance with ISO 1402, the hose shall meet the requirements given in Table 4.Table 4 Hydrostatic pressure requirementsHose type Working pressure Proof p
46、ressure Minimum bursting pressureMPa bar MPa bar MPa barA 1 10 2 20 4 40B 4 40 8 80 16 160C 6 60 12 120 24 240 ISO 2016 All rights reserved 3BS EN ISO 1401:2016ISO 1401:2016(E)8.2.2 Hydrostatic testing after ageing in liquidA 1 m length of hose shall be filled with the liquid to be used in the hose
47、and aged for 336 h 2 h at standard laboratory temperature (see ISO 23529). After ageing, the hose shall be drained and hydrostatically tested after 1 h in accordance with ISO 1402. The hose shall meet the requirements given in Table 4.8.3 Bending test requirementsWhen determined in accordance with I
48、SO 10619-1 using a minimum radius of curvature of 10 times the nominal bore, the value of the ratio of hose outside dimension, during bending, to the original outside diameter, T/D, shall be a minimum of 0,80.8.4 AdhesionWhen determined in accordance with ISO 8033, the adhesion between the various c
49、omponents shall be no less than 1,5 kN/m.8.5 Resistance to ozoneWhen tested in accordance with ISO 7326:2006, method 1, the test piece shall show no signs of cracking.9 Frequency of testingThe minimum frequency of testing (routine tests and type tests) shall conform to the schedule given in Annex A. The recommended frequency of production acceptance testing carried out per batch is given in Annex B and is for guidance only.Routine tests are those tests carried out on each length of finished hos
