1、BRITISH STANDARD BS EN ISO 5084:1997 Textiles Determination of thickness of textiles and textile products The European Standard EN ISO 5084:1996 has the status of a British Standard ICS 59.080.01BSEN ISO 5084:1997 This British Standard, having been prepared under the directionof the Sector Board for
2、Materials and Chemicals, waspublished under the authorityof the Standards Boardand comes into effect on 15 January 1997 BSI 10-1998 The following BSI references relate to the work on this standard: Committee reference TCI/24 Draft for comment 94/304611 DC ISBN 0 580 26909 4 Committees responsible fo
3、r this British Standard The preparation of this British Standard was entrusted to Technical Committee TCI/24, Physical testing of textiles, upon which the following bodies were represented: Association of Consulting Scientists Association of Suppliers to the British Clothing Industry British Apparel
4、 and Textile Confederation British Measurement and Testing Association British Polyolefin Textiles Association British Retail Consortium British Textile Machinery Association British Textile Technology Group British Throwsters Association International Wool Secretariat Ministry of Defence Royal Phar
5、maceutical Society of Great Britain SATRA Footwear Technology Centre Soap and Detergent Industry Association Society of Dyers and Colourists Textile Finishers Association Textile Institute United Kingdom Accreditation Service Amendments issued since publication Amd. No. Date CommentsBS EN ISO 5084:1
6、997 BSI 10-1998 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Definition 3 4 Principle 3 5 Apparatus 3 6 Atmosphere for conditioning and testing 3 7 Sampling, selection and conditioning of specimens 3 8 Procedure 4 9 Ex
7、pression of results 4 10 Test report 4 Annex A (normative) Test area position and alternatives for presser-foot area and applied pressure 5 Annex B (informative) Bibliography 6 Annex ZA (normative) Normative references to international publications with their relevant European publications Inside ba
8、ck cover Figure A.1 Position of test areas or test specimens 5BS EN ISO 5084:1997 ii BSI 10-1998 National foreword This British Standard has been prepared under the direction of the Sector Board for Construction and Materials and is the English language version of ISO5084:1996 Textiles Determination
9、 of thickness of textiles and textile products published by the European Committee for Standardization (CEN). It is identical with ISO5084:1996 published by the International Organization for Standardization (ISO). It supersedes BS2544:1987 which is withdrawn. A British Standard does not purport to
10、include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corresponding British Standard EN 20139
11、:1992 (ISO 139:1973) BS EN 20139:1992 Textiles. Standard atmospheres for conditioning and testing BS EN 30012 Quality assurance requirements for measuring equipment EN 30012-1:1993 (ISO 10012-1:1992) BS EN 30012-1:1993 Metrological confirmation system for measuring equipment Summary of pages This do
12、cument comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front
13、 cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 5084 September 1996 ICS 59.080 Descriptors: Textiles, textile products, fabrics, determination, thickness, thickness measurement English version Textiles Determination of thickness of textiles and textile products (ISO 5084:1996) Textil
14、es Dtermination de lepaisseur des textiles et produits textiles (ISO5084:1996) Textilien Bestimmung der Dicke von Textilien und textilen Erzeugnissen (ISO5084:1996) This European Standard was approved by CEN on 1996-07-12. CEN members are bound to comply with the CEN/CENELEC Internal Regulations whi
15、ch stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Sta
16、ndard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national sta
17、ndards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Ce
18、ntral Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN ISO 5084:1996 EEN ISO5084:1996 BSI 10-1998 2 Foreword The text of the International Standard ISO 5084:1996 has been prepared by Technical Committee ISO/TC 38, Textiles, in collaboration with Tec
19、hnical Committee CEN/TC 248, Textiles and textile products, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March1997, and conflicting national standards s
20、hall be withdrawn at the latest by March1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemb
21、ourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTENormative references to International Standards are listed in annex ZA (normative).EN ISO 5084:1996 BSI 10-1998 3 1 Scope This International Standard specifies a method for the determination of the thickness
22、of textiles and textile products when under a specified pressure. It is not applicable to textile floor coverings, nonwovens, geotextiles and coated fabrics for which specific International Standards exist (seeannex B). 2 Normative references The following standards contain provisions which, through
23、 reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applyin
24、g the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 139:1973, Textiles Standard atmospheres for conditioning and testing. ISO 10012-1:1992, Quality assurance requirements for measuring equipment Part 1
25、: Metrological confirmation system for measuring equipment. 3 Definition For the purposes of this International Standard, the following definition applies. 3.1 thickness of a textile perpendicular distance between two reference plates exerting a pressure of 1 kPa or less on the textile 4 Principle T
26、he thickness of a specimen is measured as the distance between the reference plate on which the specimen rests and a parallel circular presser-foot that exerts a specified pressure on the area of the textile under test. A test specimen is placed between two reference plates which exert a known press
27、ure on the specimen. The perpendicular distance between the reference plates is measured and recorded after a specified time. 5 Apparatus 5.1 Thickness tester The confirmation system for the thickness tester shall comply with ISO 10012-1. The thickness tester shall incorporate (or be equipped with)
28、the following elements. 5.1.1 Interchangeable presser-feet, of area appropriate to the type of fabric to be tested. The recommended pressure-foot area for the test is(2 000 20) mm 2 , corresponding to a circular presser-foot of diameter (50,5 0,2) mm (seealsoannex A). If other test areas have to be
29、used, this shall be agreed by the interested parties and shall be stated in the test report. 5.1.2 Reference plate, with a plane upper surface of diameter at least 50mm greater than that of the presser-foot(5.1.1). 5.1.3 Means for moving the presser-foot (in a direction normal to the upper surface o
30、f the reference plate), so that its bearing surface is maintained horizontal and parallel to the upper surface of the reference plate (5.1.2) and so that pressures of (1 0,01) kPa and (0,1 0,001) kPa can be applied to a test specimen supported on the plate (see annex A). 5.1.4 Thickness gauge, capab
31、le of registering the distance between the bearing surface of the presser-foot (5.1.1) and the reference plate (5.1.2) to an accuracy of 0,01 mm. 5.2 Stopwatch 6 Atmosphere for conditioning and testing The textile samples shall be conditioned and the test conducted in the standard atmosphere for con
32、ditioning and testing of textiles specified inISO139. 7 Sampling, selection and conditioning of specimens 7.1 Take samples in one of the following ways, as appropriate: a) in accordance with the directions given in the relevant material specification; b) if such directions are not included in the ma
33、terial specification, in accordance with the procedure agreed upon by the parties interested in the test results. 7.2 Select test areas for samples in accordance with clause A.3. For fabrics which are sensitive to deformation, e.g. certain knitted fabrics, cut test specimens in accordance with claus
34、e A.3. If wide-width fabrics cannot be handled without distortion, cut test specimens. 7.3 Condition the samples or test specimens in the relaxed state until equilibrium is reached with the standard atmosphere for testing. NOTE 1It is recommended to condition the samples at least for16 h in the rela
35、xed state.EN ISO 5084:1996 4 BSI 10-1998 8 Procedure 8.1 Clean the presser-foot (5.1.1) and the reference plate (5.1.2). Check that the presser-foot shaft moves freely. Load the presser-foot to exert the appropriate specified pressure on the reference plate, and set the thickness gauge (5.1.4) to re
36、ad zero. An applied pressure of (1 0,01) kPa is recommended. 8.2 Raise the presser-foot and position the sample or test specimen, without tension and distortion, on the reference plate so that no part of the area to be measured is closer than 150 mm to the selvedge. Ensure that the area chosen for t
37、he test is free from creases. 8.3 Lower the presser-foot gently onto the specimen and note the gauge reading after (30 5) s. 8.4 Determine, in accordance with the procedure in8.2 and 8.3, the thickness of at least five different areas on the sample or at least five test specimens (see annex A). 9 Ex
38、pression of results Calculate the arithmetic mean of the measurements determined in accordance with clause 8 to an accuracy of 0,01mm. Calculate the coefficient of variation to the nearest 0,1 % and the 95 % confidence limits to the nearest 0,01 mm. 10 Test report The test report shall include at le
39、ast the following information: a) statement that the test was conducted in accordance with this International Standard, and date of test; b) description of the fabric; width of narrow fabrics, if relevant; c) area of the presser-foot used; d) applied pressure; e) number of tests; f) thickness of the
40、 textile or textile product, presented as the arithmetic mean, expressed in millimetres and, if required, the coefficient of variation expressed as a percentage and the 95 % confidence limits, expressed in millimetres (seeclause9); g) any deviation, by agreement or otherwise, from the procedure spec
41、ified, and the reasons for this.EN ISO 5084:1996 BSI 10-1998 5 Annex A (normative) Test area position and alternatives for presser-foot area and applied pressure A.1 Presser-foot If the test area of the presser-foot recommended in5.1.1 is not used, then use one of the following: for narrow fabrics,
42、e.g. usable width less than50 mm, test area (100 1) mm 2corresponding to a circular presser-foot of diameter (11,28 0,05) mm; for other fabrics, test area (10 000 100) mm 2corresponding to a circular presser-foot of diameter (112,84 0,5) mm. A.2 Applied pressure If the pressure recommended in 8.1 is
43、 not used, then use (0,1 0,001) kPa, e.g. for raised, pile or loop fabrics and certain knitted fabrics. A.3 Test areas The position of test areas or test specimens on the textile sample is shown in Figure A.1. Figure A.1 Position of test areas or test specimensEN ISO 5084:1996 6 BSI 10-1998 Annex B
44、(informative) Bibliography For determination of thickness of textile floor coverings or nonwovens or geotextiles see: 1 ISO 1765:1986, Machine-made textile floor coverings Determination of thickness. 2 ISO 9073-2:1995, Textiles Test methods for nonwovens Part 2: Determination of thickness. 3 ISO 986
45、3:1990, Geotextiles Determination of thickness at specified pressures.EN ISO 5084:1996 BSI 10-1998 Annex ZA (normative) Normative references to international publications with their relevent European publications This European Standard incorporates by dated or undated reference, provisions from othe
46、r publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or
47、revision. For undated references the latest edition of the publication referred to applies. Publication Year Title EN Year ISO 139 1973 Textiles Standard atmospheres for conditioning and testing EN 20 139 1992BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | |
48、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing
49、 British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary
