BS EN ISO 5456-2-1999 Technical drawings - Projection methods - Orthographic representations《技术图纸 投影法 正交表示法》.pdf

上传人:towelfact221 文档编号:579547 上传时间:2018-12-13 格式:PDF 页数:20 大小:599.98KB
下载 相关 举报
BS EN ISO 5456-2-1999 Technical drawings - Projection methods - Orthographic representations《技术图纸 投影法 正交表示法》.pdf_第1页
第1页 / 共20页
BS EN ISO 5456-2-1999 Technical drawings - Projection methods - Orthographic representations《技术图纸 投影法 正交表示法》.pdf_第2页
第2页 / 共20页
BS EN ISO 5456-2-1999 Technical drawings - Projection methods - Orthographic representations《技术图纸 投影法 正交表示法》.pdf_第3页
第3页 / 共20页
BS EN ISO 5456-2-1999 Technical drawings - Projection methods - Orthographic representations《技术图纸 投影法 正交表示法》.pdf_第4页
第4页 / 共20页
BS EN ISO 5456-2-1999 Technical drawings - Projection methods - Orthographic representations《技术图纸 投影法 正交表示法》.pdf_第5页
第5页 / 共20页
亲,该文档总共20页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、BRITISH STANDARD BS EN ISO 5456-2:1999 Technical drawings Projection methods Part 2: Orthographic representations The European Standard EN ISO 5456-2:1999 has the status of a British Standard ICS 01.100.01 BS EN ISO 5456-2:1999 This British Standard, having been prepared under the direction of the E

2、ngineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 October 1999 BSI 15 September 2002 ISBN 0 580 35160 2 National foreword This British Standard is the English language version of EN ISO 5456-2:1999. It is identical with ISO 5456-2:1

3、996. The UK participation in its preparation was entrusted to Technical Committee TDE/4, Engineering drawing, metrology, precision measurement and all related documentation, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secre

4、tary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European publications r

5、eferred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of

6、 a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the

7、interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO

8、title page, pages ii to iv, pages 1 to 10, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 5456-2

9、 July 1999 ICS 01.100.10 English version Technical drawings Projection methods Part 2: Orthographic representations (ISO 5456-2:1996) Dessins techniques Mthodes des projection Partie 2: Reprsentations orthographiques (ISO 5456-2:1996) Technische Zeichnungen Projektionsmethoden Teil 2: Orthogonale Da

10、rstellungen (ISO 5456-2:1996) This European Standard was approved by CEN on 27 May 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lis

11、ts and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respo

12、nsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Net

13、herlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any mean

14、s reserved worldwide for CEN national Members. Ref. No. EN ISO 5456-2:1999 EEN ISO 5456-2:1999 BSI 15 September 2002 Foreword The text of the International Standard from Technical Committee ISO/TC 10, Technical drawings, product definition and related documentation, of the International Organization

15、 for Standardization (ISO) has been taken over as a European Standard CEN/CS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2000, and conflicting national standards shall be withdrawn at

16、 the latest by January 2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembo

17、urg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 5456-2:1996 has been approved by CEN as a European Standard without any modification. NOTE Normative references to International Standards are listed i

18、n Annex ZA (normative).EN ISO 5456-2:1999 ii BSI 15 September 2002 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical

19、 committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with

20、 the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of th

21、e member bodies casting a vote. International Standard ISO 5456-2 was prepared by Technical Committee ISO/TC 10, Technical drawings, product definition and related documentation, Subcommittee SC 1, Basic conventions. ISO 5456 consists of the following parts, under the general title Technical drawing

22、s Projection methods: Part 1: Synopsis Part 2: Orthographic representations Part 3: Axonometric representations Part 4: Central projection Annex A forms an integral part of this part of ISO 5456. Descriptors: graphic methods, drawings, technical drawings, graphic projections.EN ISO 5456-2:1999 BSI 1

23、5 September 2002 iii Introduction Orthographic representation in its various forms is the most widely used method of representing technical objects in all fields of technical drawing (mechanical, electrical, construction, etc.), and is thus considered to be the accepted technical language.iv blankEN

24、 ISO 5456-2:1999 BSI 15 September 2002 1 1 Scope This part of ISO 5456 specifies basic rules for the application of orthographic representation to all types of technical drawings in all technical fields, according to the general rules specified in ISO 128, ISO 129, ISO 3098-1, ISO 3461-2 and ISO 545

25、6-1. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 5456. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this

26、part of ISO 5456 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 128:1982, Technical drawings General principles of presentation. ISO 129:198

27、5, Technical drawings Dimensioning General principles, definitions, methods of execution and special indications. ISO 3098-1:1974, Technical drawings Lettering Part 1: Currently used characters. ISO 3461-2:1987, General principles for the creation of graphical symbols Part 2: Graphical symbols for u

28、se in technical product documentation. ISO 5456-1:1996, Technical drawings Projection methods Part 1: Synopsis. ISO 10209-1:1992, Technical product documentation Vocabulary Part 1: Terms relating to technical drawings: general and types of drawings. ISO 10209-2:1993, Technical product documentation

29、Vocabulary Part 2: Terms relating to projection methods. 3 Definitions For the purposes of this part of ISO 5456, the definitions given in ISO 5456-1, ISO 10209-1 and ISO 10209-2 apply.EN ISO 5456-2:1999 2 BSI 15 September 2002 4 General principles 4.1 General Orthographic representation is obtained

30、 by means of parallel orthogonal projections and results in flat, two-dimensional views systematically positioned relative to each other. To show an object completely, the six views in the directions a, b, c, d, e and f may be necessary, in order of priority (see Figure 1 and Table 1). 4.2 Designati

31、on of views See Table 1. Table 1 The most informative view of the object to be represented is normally chosen as the principal view (front view). This is view A according to the direction of viewing a (see Figure 1 and Table 1), generally showing the object in the functioning or manufacturing or mou

32、nting position. The position of other views relative to the principal view in the drawing depends on the projection method chosen (first angle, third angle, reference arrows). In practice, not all six views (A to F) are needed. When views (cuts or sections) other than the principal view are necessar

33、y, these shall be selected in order to: limit the number of views, cuts and sections to the minimum necessary and sufficient to fully represent the object without ambiguity; avoid unnecessary repetition of detail. Figure 1 Direction of observation Designation of view View in direction View from at h

34、 e f r o n t A ba b o v e B (E) 1) ct h e l e f t C dt h e r i g h t D e below E ft h e r e a r F 1) See 5.4.EN ISO 5456-2:1999 BSI 15 September 2002 3 5 Methods of representation 5.1 First angle projection The first angle projection method is an orthographic representation in which the object to be

35、 represented (see Figure 1) appears between the observer and the coordinate planes on which the object is orthogonally projected (seeFigure 2). The positions of the various views relative to the principal (front) view A are determined by rotating their projection planes around lines coinciding with

36、or parallel to the coordinate axes on the coordinate plane (drawing surface) on which the front view A is projected (see Figure 2). Therefore, in the drawing, with reference to the principal view A, the other views are arranged as follows (see Figure 3): View B: the view from above is placed underne

37、ath; View E: the view from below is placed above; View C: the view from left is placed on the right; View D: the view from the right is placed on the left; View F: the view from the rear is placed on the right or on the left, as convenient. The identifying graphical symbol of this method is shown in

38、 Figure 4. Figure 2EN ISO 5456-2:1999 4 BSI 15 September 2002 5.2 Third angle projection The third angle projection method is an orthographic representation in which the object to be represented (see Figure 1), as seen by the observer, appears behind the coordinate planes on which the object is orth

39、ogonally projected (see Figure 5). On each projection plane, the object is represented as if seen orthogonally from infinite distance with transparent projection planes. The positions of the various views relative to the principal (front) view A are determined by rotating their projection planes aro

40、und lines coinciding with or parallel to the coordinate axes on the coordinate plane (drawing surface) on which the front view A is projected (see Figure 5). Therefore, in the drawing, with reference to the principal view A, the other views are arranged as follows (seeFigure 6): View B: the view fro

41、m above is placed above; View E: the view from below is placed underneath; View C: the view from the left is placed on the left; View D: the view from the right is placed on the right; View F: the view from the rear may be placed on the left or on the right, as convenient. The identifying graphical

42、symbol of this method is shown in Figure 7. Figure 3 Figure 4EN ISO 5456-2:1999 BSI 15 September 2002 5 Figure 5 Figure 6EN ISO 5456-2:1999 6 BSI 15 September 2002 5.3 Reference arrows layout In those cases where it is advantageous to position the views not according to the strict pattern of the fir

43、st or the third angle projection method, the use of the reference arrows method permits the various views to be freely positioned. With the exception of the principal view, each view shall be identified by a letter in accordance with Figure 1. A lower-case letter indicates in the principal view the

44、direction of observation of the other views, which are identified by the corresponding capital letter placed immediately above the view and on the left. The identified views may be located irrespective of the principal view (see Figure 8). Whatever the direction of observation, the capital letters (

45、see ISO 3098-1) identifying the views shall always be positioned to be read from the normal direction of viewing of the drawing. No graphical symbol for the indication of this method is needed on the drawing. 5.4 Mirrored orthographic representation Mirrored orthographic representations 1)is an orth

46、ographic representation in which the object to be represented (see Figure 1) is a reproduction of the image in a mirror (face up) which is positioned parallel to the horizontal planes of this object (see Figure 9). The view resulting from a mirrored orthographic representation may be indicated by us

47、ing the capital letter for the designation of views (i.e. “E”, see 4.2). Figure 7 Figure 8 1) This method is preferably used in construction drawings.EN ISO 5456-2:1999 BSI 15 September 2002 7 The identifying graphical symbol of this method is shown in Figure 10. Figure 9 Figure 10EN ISO 5456-2:1999

48、 8 BSI 15 September 2002 Annex A (normative) Proportions and dimensions of graphical symbols A.1 General requirements In order to harmonize the sizes of the graphical symbols specified in this part of ISO 5456 with those of the other inscriptions on the drawing (dimensions, tolerances, etc.), the ru

49、les given in ISO 3461-2 shall be applied. A.2 Proportions The graphical symbols shall be drawn in accordance with Figure A.1, Figure A.2 and Figure A.3. For practical reasons the centrelines may be omitted. Figure A.1 Figure A.2EN ISO 5456-2:1999 BSI 15 September 2002 9 A.3 Dimensions The range of sizes to be used for the graphical symbols and additional indications shall be as specified in Table A.1.

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1