1、BS EN ISO9445-1:2010ICS 77.140.20; 77.140.50NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDContinuously cold-rolled stainless steel Tolerances ondimensions and formPart 1: Narrow strip and cut lengths(ISO 9445-1:2009)This British Standard was published under th
2、e authority of the Standards Policy and Strategy Committee on 31 March 2010 BSI 2010ISBN 978 0 580 60753 0Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 9445-1:2010National forewordThis British Standard is the UK implementation of EN ISO 9445-1:2010. It is identical to ISO 9445
3、-1:2009. Together with BS EN 9445-2:2010, it supersedes BS EN ISO 9445:2006 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/105, Steels for Heat Treatment, Alloy Steels, Free-Cutting Steels and Stainless Steels.A list of organizations represented o
4、n this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.EUROPEAN STANDARD N
5、ORME EUROPENNE EUROPISCHE NORM EN ISO 9445-1 March 2010 ICS 77.140.20; 77.140.50 Supersedes EN ISO 9445:2006English Version Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 1: Narrow strip and cut lengths (ISO 9445-1:2009) Acier inoxydable lamin froid en continu -
6、Tolrances sur les dimensions et la forme - Partie 1: Bandes troites et feuillards coups longueur (ISO 9445-1:2009) Kontinuierlich kaltgewalzter nichtrostender Stahl - Grenzabmae und Formtoleranzen - Teil 1: Kaltband und Kaltband in Stben (ISO 9445-1:2009) This European Standard was approved by CEN o
7、n 7 February 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards m
8、ay be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the
9、CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta
10、, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploi
11、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9445-1:2010: EBS EN ISO 9445-1:2010EN ISO 9445-1:2010 (E) 3 Foreword The text of ISO 9445-1:2009 has been prepared by Technical Committee ISO/TC 17 “Steel” of the International Organization for Standardi
12、zation (ISO) and has been taken over as EN ISO 9445-1:2010 by Technical Committee ECISS/TC 105 “Steels for heat treatment, alloy steels, free-cutting steels and stainless steels” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either
13、by publication of an identical text or by endorsement, at the latest by September 2010, and conflicting national standards shall be withdrawn at the latest by September 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and
14、/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 9445:2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austri
15、a, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. En
16、dorsement notice The text of ISO 9445-1:2009 has been approved by CEN as a EN ISO 9445-1:2010 without any modification. BS EN ISO 9445-1:2010ISO 9445-1:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Information to
17、 be supplied by the purchaser 1 5 Type of delivery and delivery conditions . 2 6 Tolerances on thickness for cold-rolled narrow strip and products obtained from cold-rolled narrow strip 3 7 Tolerances on width for cold-rolled narrow strip and products obtained from cold-rolled narrow strip . 4 8 Pre
18、ferred coil inner diameters for cold-rolled narrow strip . 4 9 Tolerances on length for cut lengths obtained from cold-rolled narrow strip. 4 10 Tolerances on edge camber for cold-rolled narrow strip and cut lengths obtained from cold-rolled narrow strip 5 11 Tolerances on squareness for cut lengths
19、 obtained from cold-rolled narrow strip 5 12 Tolerances on flatness for cut lengths obtained from cold-rolled narrow strip 5 13 Edge waviness tolerances for cold-rolled strip. 5 14 Form of coils . 6 15 Ordered format for cut lengths 6 16 Measurement of thickness for cold-rolled narrow strip and cut
20、lengths obtained from cold-rolled narrow strip 6 17 Measurement of width 6 18 Measurement of length. 6 19 Measurement of edge camber . 6 20 Measurement of squareness . 7 21 Measurement of flatness and waviness . 8 BS EN ISO 9445-1:2010ISO 9445-1:2009(E) iv ISO 2009 All rights reservedForeword ISO (t
21、he International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical commit
22、tee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotech
23、nical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member
24、 bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying
25、 any or all such patent rights. ISO 9445-1 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 4, Heat treatable and alloy steels. This first edition of ISO 9445-1, together with ISO 9445-2, cancels and replaces ISO 9445:2002, the contents of which have been technically revised and
26、 separated into two parts. ISO 9445 consists of the following parts, under the general title Continuously cold-rolled stainless steel Tolerances on dimensions and form: Part 1: Narrow strip and cut lengths Part 2: Wide strip and plate/sheet BS EN ISO 9445-1:2010INTERNATIONAL STANDARD ISO 9445-1:2009
27、(E) ISO 2009 All rights reserved 1Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 1: Narrow strip and cut lengths 1 Scope This part of ISO 9445 specifies the tolerances on dimensions and form for continuously cold-rolled stainless steel narrow strip, in thicknesses of
28、 up to and including 3 mm and in rolling widths of less than 600 mm. It also applies to cut lengths taken from such strip. Narrow strip and cut lengths with widths of less than 600 mm, which are manufactured from wide strip by longitudinal slitting, are covered in ISO 9445-2. 2 Normative references
29、The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6929, Steel products Definitions and classifi
30、cation 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6929 apply. 4 Information to be supplied by the purchaser 4.1 It shall be the responsibility of the purchaser to specify all requirements that are necessary for products under this specification.
31、 Such requirements to be considered include, in the order listed, but are not limited to, the following: a) the type of delivery see 5.2 a) and 5.2 b); b) the number of this International Standard, i.e. ISO 9445-1; c) the thickness in millimetres (if necessary accurate to two decimal places) and, if
32、 required, including the relevant code letter (F or P) for a fine or precision tolerance; d) the width in millimetres and, if required, including the relevant code letter (F or P) for a fine or precision tolerance; e) the code letter R where a restricted tolerance on edge camber is required; BS EN I
33、SO 9445-1:2010ISO 9445-1:2009(E) 2 ISO 2009 All rights reservedf) for cut lengths, the length in millimetres and, if a special tolerance is required, the code letter S; g) for cut lengths, the code letters FS where a special tolerance is required for flatness (see Clause 12); h) any special requirem
34、ent for edge condition (see 5.3). EXAMPLE 1 Cold-rolled narrow strip according to this part of ISO 9445 with a specified thickness of 0,25 mm, precision thickness tolerance (P), with a specified width of 250 mm, precision tolerance on width (P), and with restricted tolerance on edge camber (R). Cold
35、-rolled narrow strip ISO 9445-1 0,25P x 250P-R EXAMPLE 2 Cold-rolled cut lengths according to this part of ISO 9445 with a specified thickness of 1,00 mm, fine thickness tolerance (F), width 40 mm, fine width tolerance (F), restricted tolerance on edge camber R, length 1 000 mm, special tolerance on
36、 length (S), special tolerance on flatness (FS) and rounded edges. Cold-rolled cut lengths ISO 9445-1 1,00F x 40F-R x 1000S-FS, rounded edges 4.2 In the absence of information in the order concerning special requirements for tolerances on dimension, shape and edge condition see 4.1 c), d), e), f), g
37、) and h), flat products covered by this part of ISO 9445 will be delivered according to the basic specifications of this part of ISO 9445, i.e. with normal tolerances. 5 Type of delivery and delivery conditions 5.1 General In the absence of agreements at the time of enquiry and order concerning spec
38、ial requirements for the delivery conditions given in 5.3, flat products covered by this part of ISO 9445 will be delivered according to the basic specifications of this part of ISO 9445. 5.2 Type of delivery Flat products according to this part of ISO 9445 can be supplied as a) cold-rolled narrow s
39、trip (strip in rolled widths less than 600 mm); b) cut lengths from cold-rolled narrow strip cut from cold-rolled narrow strip according to item 5.2 a). 5.3 Delivery conditions of cold-rolled narrow strip and products obtained from cold-rolled narrow strip 5.3.1 Cold-rolled narrow strip and cut leng
40、ths obtained from cold-rolled narrow strip are usually supplied with cut edges. These products will have burrs caused by cutting. If there are special requirements for these edges, corresponding agreements shall be made on ordering. In this case, the strip is deemed to be cut almost free of burrs if
41、 the height of the burr is less than 10 % of the product thickness. 5.3.2 By special agreement and depending on the technical equipment of the supplier, cold-rolled narrow strip and cut lengths obtained from cold-rolled narrow strip can be delivered with special edges, e.g. deburred or rounded edges
42、. BS EN ISO 9445-1:2010ISO 9445-1:2009(E) ISO 2009 All rights reserved 36 Tolerances on thickness for cold-rolled narrow strip and products obtained from cold-rolled narrow strip The tolerances on thickness are given in Table 1. Table 1 Tolerances on specified thickness for cold-rolled narrow strip
43、and cut lengths obtained from cold-rolled narrow strip Dimensions in millimetres Tolerance on specified thickness for nominal width of Specified thickness w 125 125 u w 250 250 u w 600 t Normal Fine (F) Precision(P) Normal Fine (F) Precision (P) Normal Fine (F) Precision(P) 0,05au t 0,10 0,10 t 0,06
44、 t 0,04 t 0,12 t 0,10 t 0,08 t 0,15 t 0,10 t 0,08 t 0,10 u t 0,15 0,010 0,008 0,006 0,015 0,012 0,008 0,020 0,015 0,010 0,15 u t 0,20 0,015 0,010 0,008 0,020 0,012 0,010 0,025 0,015 0,012 0,20 u t 0,25 0,015 0,012 0,008 0,020 0,015 0,010 0,025 0,020 0,012 0,25 u t 0,30 0,017 0,012 0,009 0,025 0,015
45、0,012 0,030 0,020 0,015 0,30 u t 0,40 0,020 0,015 0,010 0,025 0,020 0,012 0,030 0,025 0,015 0,40 u t 0,50 0,025 0,020 0,012 0,030 0,020 0,015 0,035 0,025 0,018 0,50 u t 0,60 0,030 0,020 0,014 0,030 0,025 0,015 0,040 0,030 0,020 0,60 u t 0,80 0,030 0,025 0,015 0,035 0,030 0,018 0,040 0,035 0,025 0,80
46、 u t 1,00 0,030 0,025 0,018 0,040 0,030 0,020 0,050 0,035 0,025 1,00 u t 1,20 0,035 0,030 0,020 0,045 0,035 0,025 0,050 0,040 0,030 1,20 u t 1,50 0,040 0,030 0,020 0,050 0,035 0,025 0,060 0,045 0,030 1,50 u t 2,00 0,050 0,035 0,025 0,060 0,040 0,030 0,070 0,050 0,035 2,00 u t 2,50 0,050 0,035 0,025
47、0,070 0,045 0,030 0,080 0,060 0,040 2,50 u t u 3,00 0,060 0,045 0,030 0,070 0,050 0,035 0,090 0,070 0,045 NOTE By agreement, the tolerances may alternatively be totally + or totally or unevenly distributed. In any case, the total range of the tolerance shall remain as in the table. aFor thicknesses
48、below 0,05 mm, the values for the tolerances are to be agreed at the time of enquiry and order. BS EN ISO 9445-1:2010ISO 9445-1:2009(E) 4 ISO 2009 All rights reserved7 Tolerances on width for cold-rolled narrow strip and products obtained from cold-rolled narrow strip The tolerances on width are given in Table 2. Table 2 Tolerances on width for cold-rolled narrow strip and cut lengths obtained from cold-rolled narrow strip Dimensions in millimetres Specified width Specified thickness w u 40 40 w u 125 125 w u 250 250 w 600 t Normal Fine (F) Preci-sion
