1、BSI Standards PublicationBS ISO 10649-1:2013Cutter arbors with parallel keyand tenon drivePart 1: General dimensionsBS ISO 10649-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 10649-1:2013.It supersedes BS ISO 10649-1:2010 which is withdrawn.The UK part
2、icipation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a cont
3、ract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 77003 6ICS 25.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho
4、rity of theStandards Policy and Strategy Committee on 30 November 2013.Amendments issued since publicationDate Text affectedBS ISO 10649-1:2013 ISO 2013Cutter arbors with parallel key and tenon drive Part 1: General dimensionsMandrins porte-fraise entranement par clavette et tenon Partie 1: Dimensio
5、ns gnralesINTERNATIONAL STANDARDISO10649-1Second edition2013-10-15Reference numberISO 10649-1:2013(E)BS ISO 10649-1:2013ISO 10649-1:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduce
6、d or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO
7、 copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 10649-1:2013ISO 10649-1:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13
8、 Dimensions . 13.1 General . 13.2 Dimensions of tool interface for arbors with parallel key and tenon drive 1Annex A (informative) Relationship between the symbols of this part of ISO 10649 and the ISO 13399 series . 4Bibliography 5BS ISO 10649-1:2013ISO 10649-1:2013(E)ForewordISO (the International
9、 Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been est
10、ablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardiz
11、ation.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance wi
12、th the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
13、 rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee
14、 responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, High speed steel cutting tools and their attachments.This second edition cancels and replaces the first edition (ISO 10649-1:2010), of which it constitutes a minor revision with the following changes: addition of Annex A, w
15、hich gives the relationship between the symbols of this part of ISO 10649 and the symbols according to the ISO 13399 series.ISO 10649 consists of the following parts, under the general title Cutter arbors with parallel key and tenon drive: Part 1: General dimensions Part 2: Dimensions and designatio
16、n of tool holders with taper interface with flange contact surface Part 3: Dimensions and designation of tool holders with 7/24 taper for automatic tool changer Part 4: Dimensions and designation of tool holders with 7/24 taper without automatic tool changer Part 5: Dimensions and designation of too
17、l holders with polygonal taper interface with flange contact surface Part 6: Dimensions and designation of tool holders with modular taper interface with ball track systemiv ISO 2013 All rights reservedBS ISO 10649-1:2013ISO 10649-1:2013(E)IntroductionThe aim of ISO 10649 (all parts) is to specify t
18、he main dimensions for tool holders for this type of interface, and prevent the risk of collision when exchanging the assembled tool within the machine tools. ISO 2013 All rights reserved vBS ISO 10649-1:2013BS ISO 10649-1:2013Cutter arbors with parallel key and tenon drive Part 1: General dimension
19、s1 ScopeThis part of ISO 10649 specifies the dimensions of tool interface for cutter arbors with parallel key and tenon drive.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated reference
20、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 2768-2, General tolerances Part
21、2: Geometrical tolerances for features without individual tolerance indicationsISO 2780, Milling cutters with tenon drive Interchangeability dimensions for cutter arbors Metric seriesISO 10643, Dimensions of accessories for cutter arbors with parallel key and tenon drive3 Dimensions3.1 GeneralAll di
22、mensions and tolerances are given in millimetres. Tolerances not specified shall be of tolerance class “m” in accordance with ISO 2768-1 and of class “K” in accordance with ISO 2768-2.The figures are schematic and are not intended to specify a given design; only the given dimension shall be met.The
23、interchangeability dimensions of the milling cutter bearing on the cutter arbors shall be in accordance with ISO 2780.3.2 Dimensions of tool interface for arbors with parallel key and tenon driveThe dimensions of tool interface for arbors with parallel key and tenon drive shall be in accordance with
24、 the dimensions shown in Figure 1 and given in Table 1.INTERNATIONAL STANDARD ISO 10649-1:2013(E) ISO 2013 All rights reserved 1BS ISO 10649-1:2013ISO 10649-1:2013(E)Key1 parallel key in accordance with ISO 106432 cutter retaining screw in accordance with ISO 106433 clutch drive ring in accordance w
25、ith ISO 10643aUnder cut at the manufacturers discretion.bPositioning against the position of the cutting edge for right-hand tools with single cutting edge of the interface.cThe clutch drive ring may be fitted on spigot diameter d1.Figure 1 Dimensions of tool interface for arbors with parallel key a
26、nd tenon driveTable 1 Dimensionsd1h6d2ad3d4max.l1l2min.l3l4+0,1 +0,3l5l6 tol.l7min.l8bF9l9P916 32 M8 19 27 20 2 20 17 13,20 -0,15,5 8 422 40 M10 25 31 22 2 25 23 17,60 -0,26 10 627 48 M12 30 33 26 3 25 28 220 -0,27 12 732 58 M16 36 38 30 3 28 33 270 -0,27,5 14 8aFrom ISO 2780.bFull with depth l7.2 I
27、SO 2013 All rights reservedBS ISO 10649-1:2013ISO 10649-1:2013(E)d1h6d2ad3d4max.l1l2min.l3l4+0,1 +0,3l5l6 tol.l7min.l8bF9l9P940 70 M20 44 41 34 3 32 41 34,50 -0,28,5 16 1050 90 M24 54 46 40 3 36 51 44,50 -0,29,5 18 12aFrom ISO 2780.bFull with depth l7.Table 1 (continued) ISO 2013 All rights reserved
28、 3BS ISO 10649-1:2013ISO 10649-1:2013(E)Annex A (informative) Relationship between the symbols of this part of ISO 10649 and the ISO 13399 seriesAs this part of ISO 10649 does not define an entire product, the relationship between the symbols of this part of ISO 10649 and symbols according to the IS
29、O 13399 series are not given. They are given in the entire product standards ISO 10649-2, ISO 10649-3, ISO 10649-4, ISO 10649-5 and ISO 10649-6, and future parts to be developed.4 ISO 2013 All rights reservedBS ISO 10649-1:2013ISO 10649-1:2013(E)Bibliography1 ISO 13399 (all parts), Cutting tool data
30、 representation and exchange ISO 2013 All rights reserved 5BS ISO 10649-1:2013ISO 10649-1:2013(E) ISO 2013 All rights reservedICS 25.060.20Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publicati
31、ons, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry
32、, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes an
33、d across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre
34、.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizati
35、ons, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 Br
36、itish and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscript
37、ion format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of memb
38、ership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, e
39、mail .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Know
40、ledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has forma
41、lly licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise withou
42、t prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
