1、BSI Standards PublicationBS ISO 10958-2:2015Snowboards Bindingmounting areaPart 2: Requirements and test methods forsnowboards with insertsBS ISO 10958-2:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 10958-2:2015. The UK participation in its preparation
2、was entrusted to TechnicalCommittee SW/136/7, Snowsports equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicat
3、ion. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 87321 8 ICS 97.220.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Commit
4、tee on 30 June 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e d ISO 2015Snowboards Binding mounting area Part 2: Requirements and test methods for snowboards with insertsSurfs des neiges Zone de montage de la fixation Partie 2: Exigences et mthodes dessai relatives aux
5、 surfs des neiges munis dinsertsINTERNATIONAL STANDARDISO 10958-2Third edition 2015-06-15Reference number ISO 10958-2:2015(E)BS ISO 10958-2:2015ISO 10958-2:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise speci
6、fied, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or IS
7、Os member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 10958-2:2015ISO 10958-2:2015(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definit
8、ions . 14 Specifications for design of snowboard insert 25 Strength requirements . 35.1 Retention strength . 35.2 Spin resistance 36 Test apparatus . 36.1 Retention-strength test apparatus . 36.2 Spin resistance test apparatus . 47 Test procedures . 47.1 Retention-strength test procedure 47.2 Spin-r
9、esistance test procedure . 48 Marking 49 Test report . 5 ISO 2015 All rights reserved iiiContents PageBS ISO 10958-2:2015ISO 10958-2:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepari
10、ng International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in lia
11、ison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of te
12、chnical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is dra
13、wn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 10958-2 was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities and equipment, Sub
14、committee SC 4, Snowsports equipment.This third edition cancels and replaces the second edition (ISO 10958-2:2004), which has been technically revisedISO 10958 consists of the following parts, under the general title Snowboards Binding mounting area: Part 1: Requirements and test methods for snowboa
15、rds without inserts Part 2: Requirements and test methods for snowboards with insertsiv ISO 2015 All rights reservedBS ISO 10958-2:2015INTERNATIONAL STANDARD ISO 10958-2:2015(E)Snowboards Binding mounting area Part 2: Requirements and test methods for snowboards with inserts1 ScopeThis part of ISO 1
16、0958 specifies requirements and test methods for snowboards as sports equipment on which bindings are attached by means of inserts that are not removable and screws.It contains data for the manufacturer of snowboards, bindings and retention devices concerning dimensions, tests and other specificatio
17、ns for the binding mounting area.For dimensions with no tolerance indicated, a tolerance of 1 mm is valid.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition
18、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 68-1, ISO general purpose screw threads Basic profile Part 1: Metric screw threads3 Terms and definitionsFor the purposes of this document, the terms and definitions given in 6
19、8-1 and the following apply.3.1insertreusable commonly threaded attachment point permanently fixed in the snowboard at the time of manufacture, used to mount the bindings to the snowboard and typically arranged in a pattern corresponding to a particular binding manufacturers pattern3.2retention stre
20、ngthaxial pull-out force of an insert in a snowboard tested in accordance with 6.1 and 7.13.3spin resistancemoment required to rotate an insert tested in accordance with 6.2 and 7.23.4screw thread engagementenumber of threads engaged by a standard screw in an insertNote 1 to entry: See Figure 1. ISO
21、 2015 All rights reserved 1BS ISO 10958-2:2015ISO 10958-2:2015(E)3.5insert well depthidistance within the insert well from the snowboard top surface to the unobstructed bottom clearance of the binding-insertNote 1 to entry: See Figure 1.3.6countersink depthcdistance from the snowboard top surface to
22、 the first thread of the insertNote 1 to entry: See Figure 1.Figure 1 Illustration of screw thread engagement, insert well depth and countersink depth4 Specifications for design of snowboard insert4.1 Inserts shall have an M61, 6H class internal thread with standard tolerances in accordance with ISO
23、 68-1.4.2 Insert screws shall have an M61, 6g class external thread with standard tolerances in accordance with ISO 68-1.4.3 The snowboard design shall provide, for a minimum insert well depth i of 5,5 mm, a minimum screw engagement E of 2,0 threads. The length of the screw shall allow a gap between
24、 the end of the screw and the bottom of the insert. The effective threaded depth of the insert shall be at least 5,5 mm.The value of 2 threads has been verified by extensive tests carried out by snowboard manufacturers. It is recommended that self-locking screws are used.4.4 The maximum countersink
25、depth c shall be 2,5 mm.2 ISO 2015 All rights reservedBS ISO 10958-2:2015ISO 10958-2:2015(E)5 Strength requirements5.1 Retention strengthWhen tested in accordance with 7.1, inserts in a snowboard shall have a minimum retention strength of 4 500 N for those snowboards with a suggested rider mass of 4
26、5 kg or more; and a minimum retention strength of 3 500 N for those snowboards with a suggested rider mass less than 45 kg.5.2 Spin resistanceWhen tested in accordance with 7.2, inserts in a snowboard shall have a minimum spin resistance of 20 Nm.6 Test apparatus6.1 Retention-strength test apparatus
27、Universal test machine (UTM), with a pull-out device according to Figure 2, having a minimum load range of 10 000 N.Figure 2 Universal test machine with pull-out deviceThe pull-out device (see Figure 2) shall consist ofa) a rigid steel attachment plate (A) with one hole of diameter 6,5 mm,b) a unive
28、rsal joint (B) which is connected to the attachment plate and to the clamping device of the test machinec) a snowboard support (C) with two support rollers (D) with a distance (x) of 200 mm between them for snowboards with suggested rider mass of 25 kg or more and a distance (x) of 100 mm between th
29、em for snowboards with suggested rider mass of less than 25 kg, andd) a support roller (D) with a diameter (d) of 30 mm. ISO 2015 All rights reserved 3BS ISO 10958-2:2015ISO 10958-2:2015(E)6.2 Spin resistance test apparatus6.2.1 Device, capable of applying a torque directly to the insert (e.g. long
30、screw with counter-nut).6.2.2 Hand-held torque gauge, able to read to 2,5 Nm.6.2.3 C-Clamps, able to hold the snowboard stationary on a flat surface.7 Test procedures7.1 Retention-strength test procedure7.1.1 Test the snowboards at room temperature, (23 5) C.7.1.2 Cycle the UTM at a crosshead rate o
31、f 20 mm/min 4 mm/min.7.1.3 Stop the test at a load of 4 500 N, respectively 3 500 N as appropriate.7.2 Spin-resistance test procedure7.2.1 Test the inserts at room temperature, (23 5) C.7.2.2 Clamp the snowboard to a flat surface.7.2.3 Insert the test screw into the insert, engaging to the full dept
32、h of the insert.7.2.4 Torque the insert up to the required torque of 20 Nm.8 MarkingSnowboards with a suggested rider mass between 25 kg and 45 kg shall be marked with a clearly visible, permanent sign of minimum size 10 mm, placed outside the binding mounting area. The sign shall be as follows:Snow
33、boards with a suggested rider mass less than 25 kg shall be marked with a clearly visible, permanent sign of minimum size 10 mm, placed outside the binding mounting area. The sign shall be as follows:4 ISO 2015 All rights reservedBS ISO 10958-2:2015ISO 10958-2:2015(E)9 Test reportThe test report sha
34、ll include the following information:a) a reference to this part of ISO 10958, i.e ISO 10958-2:2015;b) snowboard/binding insert manufacturer, model/style and length;c) snowboard serial number;d) compliance with the requirements according to Clause 5;e) any deviations from this part of ISO 10958;f) d
35、ate of tests. ISO 2015 All rights reserved 5BS ISO 10958-2:2015ISO 10958-2:2015(E) ISO 2015 All rights reservedICS 97.220.20Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, informatio
36、n and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, c
37、onsumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all se
38、ctors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standar
39、dsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copie
40、s can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopt
41、ed European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by
42、becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please
43、visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .Revisions
44、Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Co
45、pyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed su
46、ch information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written
47、 permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
