1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 1754:2010Photography Cameras using35 mm film and roll film Dimensions of picture sizesBS ISO 1754:2010 BRITISH STANDARDNational forewordThis British Standard is the UK imp
2、lementation of ISO 1754:2010. Itsupersedes BS ISO 1754:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee CPW/42, Photography.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not pu
3、rport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 70249 5ICS 37.040.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStand
4、ards Policy and Strategy Committee on 31 August 2010.Amendments issued since publicationDate Text affectedBS ISO 1754:2010Reference numberISO 1754:2010(E)ISO 2010INTERNATIONAL STANDARD ISO1754Fifth edition2010-06-15Photography Cameras using 35 mm film and roll film Dimensions of picture sizes Photog
5、raphie Appareils photographiques utilisant des films et des pellicules de 35 mm Dimensions dimage BS ISO 1754:2010ISO 1754:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unles
6、s the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark
7、of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
8、the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, e
9、lectronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrighti
10、so.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 1754:2010ISO 1754:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pr
11、eparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, i
12、n liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main tas
13、k of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attentio
14、n is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1754 was prepared by Technical Committee ISO/TC 42, Photography. This fifth edition cancels and replaces
15、the fourth edition (ISO 1754:1998), which has been technically revised. It also incorporates the Technical Corrigendum ISO 1754:1998/Cor.1:2002. BS ISO 1754:2010BS ISO 1754:2010INTERNATIONAL STANDARD ISO 1754:2010(E) ISO 2010 All rights reserved 1Photography Cameras using 35 mm film and roll film Di
16、mensions of picture sizes 1 Scope This International Standard specifies the dimensions on the film of still picture sizes made with cameras in which the image dimensions are defined by the camera frame. Panoramic image dimensions (13 mm 36 mm) of cameras featuring a mid-roll panoramic photo are not
17、specified in this International Standard. 2 Dimensions The dimensions shown in Figure 1 are given in Table 1. Figure 1 Dimensions of picture sizes BS ISO 1754:2010ISO 1754:2010(E) 2 ISO 2010 All rights reservedTable 1 Dimensions of picture sizes Nominal picture size Dimension of picture size Trade d
18、esignation Dimensions mm Film size A mm B mm Tolerance on dimension mm Maximum corner radius R mm 18 24 18 24 17,0 24,0 24 36 24 36 24,0 36,0 0,80+0,4 13 36 13 36 135a13,3 36,4 0,4 0,4 4,5 6 45 60 41,5 56,0 6 6 60 60 56,0 56,0 6 7 60 70 56,0 69,0 6 9 60 90 120 and 220b56,0 82,6 1,0 0,8 In the case o
19、f rectangular formats, A is the shorter dimension. In the case of cameras with interchangeable lenses, the picture size given in this table applies to the picture taken by the standard lens. aSee ISO 1007 for dimensions of 135-size film. bSee ISO 732 for dimensions of 120-size and 220-size film. BS
20、ISO 1754:2010ISO 1754:2010(E) ISO 2010 All rights reserved 3Bibliography 1 ISO 732, Photography 120-size and 220-size films Dimensions 2 ISO 1007, Photography 135-size film and magazine Specifications 3 ISO 1203, Photography Roll film cameras Back window location BS ISO 1754:2010ISO 1754:2010(E) ICS
21、 37.040.10 Price based on 3 pages ISO 2010 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at th
22、e international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards
23、 should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com
24、-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 766
25、9 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 899
26、6 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Eu
27、ropeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscr
28、ibing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access
29、to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under th
30、e Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementin
31、g the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:
