1、BSI Standards PublicationBS ISO 5610-10:2014Tool holders with rectangularshank for indexable insertsPart 10: Style NBS ISO 5610-10:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-10:2014.It supersedes BS ISO 5610-10:2010 which is withdrawn.The UK part
2、icipation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a cont
3、ract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83618 3ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho
4、rity of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-10:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 10: Style NPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 10: For
5、me NINTERNATIONAL STANDARDISO5610-10Second edition2014-09-01Reference numberISO 5610-10:2014(E)BS ISO 5610-10:2014ISO 5610-10:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or u
6、tilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyr
7、ight officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-10:2014ISO 5610-10:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 G
8、eneral . 13.2 Tool holder style N for rhombic indexable insert shape D 23.3 Tool holder style N for triangular indexable insert shape T 44 Designation 55 Material 66 Design 66.1 Type of mounting 66.2 Corner radius, r66.3 Thickness, s, of indexable insert . 77 Extent of delivery . 78 Marking 7Bibliog
9、raphy 8BS ISO 5610-10:2014ISO 5610-10:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each membe
10、r body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Elec
11、trotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types o
12、f ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be hel
13、d responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is informatio
14、n given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the fol
15、lowing URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610-10:2010), of which it constitutes a minor rev
16、ision.ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part
17、8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-10:2014ISO 5610-10:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-10:2014BS ISO 5610-10:2014Tool holders with rectangular shan
18、k for indexable inserts Part 10: Style N1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style N, i.e. with straight shank and cutting edge angle r= 63 for side cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting mate
19、rials to be mounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normativ
20、e referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appl
21、ies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holder
22、s to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures a
23、re recommended values; they can vary according to the application.INTERNATIONAL STANDARD ISO 5610-10:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-10:2014ISO 5610-10:2014(E)3.2 Tool holder style N for rhombic indexable insert shape DKeyaInclination angle, s.bRake angle, o.cNeutral tool holders,
24、note cof Table 1.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style N for rhombic indexable insert D2 ISO 2014 All rights reservedBS ISO 5610-10:2014ISO 5610-10:2014(E)Table 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs
25、13 h13 +050,h13 k16 max.SDNCR 0808 078 8 7,75 4 8 25 2,38SDNCL 0808 07SDNCN 0808 07cSDNCR 1010 0710 10 7,75 5 10 25 2,38SDNCL 1010 07SDNCN 1010 07cSDNCR 1212 0712 12 7,75 6 12 25 2,38SDNCL 1212 07SDNCN 1212 07cSDNCR 1616 1116 16 11,6 8 16 32 3,97SDNCL 1616 11SDNCN 1616 11cSDNCR 2020 1120 20 11,6 10
26、20 32 3,97SDNCL 2020 11SDNCN 2020 11cSDNCR 2020 1520 20 15,5 10 20 404,76SDNCL 2020 15SDNCN 2020 15cPDNNR 2020 156,35PDNNL 2020 15SDNCR 2525 1525 25 15,5 12,5 25 404,76SDNCL 2525 15SDNCN 2525 15cPDNNR 2525 156,35PDNNL 2525 15SDNCR 3225 1532 25 15,5 12,5 32 404,76SDNCL 3225 15SDNCN 3225 15cPDNNR 3225
27、 156,35PDNNL 3225 15SDNCR 4032 1540 32 15,5 16 40 404,76SDNCL 4032 15SDNCN 4032 15cPDNNR 4032 156,35PDNNL 4032 15aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInser
28、t thickness without shim, if applicable.cTool holder for use in both directions of feed. The cutting edge angle r= 62,5 1 and the tolerances 0,25 mm on dimension f apply for this design. ISO 2014 All rights reserved 3BS ISO 5610-10:2014ISO 5610-10:2014(E)3.3 Tool holder style N for triangular indexa
29、ble insert shape TKeyaInclination angle, s.bRake angle, o.cTool holder style with feed of insert in both directions.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style N for triangular indexable insert T4 ISO 2014 All rights re
30、servedBS ISO 5610-10:2014ISO 5610-10:2014(E)Table 2Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.STNCR 2525 1625 25 16,5 12,5 25 323,97STNCL 2525 16PTNNR 2525 164,76PTNNL 2525 16STNCR 2525 2225 25 22 12,5 25 32 4,76STNCL 2525 22PTNNR 2525 22PTNNL 2525 22STNCR 3225 1632 2
31、5 16,5 12,5 32 323,97STNCL 3225 16PTNNR 3225 164,76PTNNL 3225 16STNCR 3225 2232 25 22 12,5 32 36 4,76STNCL 3225 22PTNNR 3225 22PTNNL 3225 22STNCR 4032 2240 32 22 16 40 36 4,76STNCL 4032 22PTNNR 4032 22PTNNL 4032 22aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 56
32、10-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 56
33、10 (i.e. ISO 5610-10);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool,
34、in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3. ISO 2014 All rights reserved 5BS ISO 5610-10:2014ISO 5610-10:2014(E)EXAMPLE 1 Tool holder for a horizontally mounted bore-clamped (P) rhombic in
35、dexable insert shape D (D), tool holder style N (N), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 40 mm and width b = 32 mm (4032), length l1= 170 mm (P), for cutting edge length l3= 15,5 mm (15) is designated as follows:Tool holder ISO 5610-10 - PDNNR 4032
36、 P15EXAMPLE 2 Tool holder for a horizontally mounted bore-clamped (P) triangular indexable insert shape T (T), tool holder style N (N), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 40 mm and width b = 32 mm (4032), length l1= 150 mm (M), for cutting edge le
37、ngth l3= 22 mm (22) is designated as follows:Tool holder ISO 5610-10 - PTNNR 4032 M225 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 a
38、nd 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating f
39、rom Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with inserts with cutting edge length, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in
40、 ISO 5610-1:2014, Table 2, apply to tool holders with inserts having corner radii, r, in accordance with Table 3.Table 3Dimensions in millimetresl3r7,75 0,411,60,815,516,522NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm and 0,794 mm
41、.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions f and l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6 ISO 2014 All rights
42、reservedBS ISO 5610-10:2014ISO 5610-10:2014(E)6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2, apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the spec
43、ified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of
44、 the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-10:2014, shall be given on the packaging. ISO 2014 All rights reserved 7BS ISO 5610-10:2014ISO 5610-10:2014(E
45、)Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO
46、3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference d
47、ictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items8 ISO 2014 All rights reservedBS ISO 5610-10:2014BS ISO 5610-10:2014ISO 5610-10:2014(E) ISO 2014 All rights reservedICS 25.100.01Price based on 8 pagesThis page d
48、eliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Stan
49、dards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assemble
