1、BSI Standards PublicationBS ISO 6361-4:2014Wrought aluminium andaluminium alloys Sheets,strips and platesPart 4: Sheets and plates: Tolerances onshape and dimensionsBS ISO 6361-4:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6361-4:2014. The UK participa
2、tion in its preparation was entrusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are respo
3、nsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 84687 8 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Stand
4、ards Policy and Strategy Committee on 30 September 2014.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e d ISO 2014Wrought aluminium and aluminium alloys Sheets, strips and plates Part 4: Sheets and plates: Tolerances on shape and dimensionsAluminium et alliages daluminium co
5、rroys Tles, bandes et tles paisses Partie 4: Tles et tles paisses: Tolrances sur forme et dimensionsINTERNATIONAL STANDARDISO 6361-4Third edition 2014-09-15Reference number ISO 6361-4:2014(E)BS ISO 6361-4:2014ISO 6361-4:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All r
6、ights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from
7、 either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6361-4:2014ISO 6361-4:2014(E) ISO 2014 All rights
8、reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensional tolerances 13.1 Thickness . 13.2 Width . 53.3 Length . 64 Shape tolerances . 74.1 Lateral curvature . 74.2 Flatness tolerances 74.3 Squareness tolerances . 10Bibliography .12BS ISO 6361-4:2014ISO 6361-4:2014(E)Forew
9、ordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technic
10、al committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of el
11、ectrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was
12、 drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such paten
13、t rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not co
14、nstitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe
15、committee responsible for this document is ISO/TC 79, Light metals and their alloys, Subcommittee SC 6, Wrought aluminium and aluminium alloys.This third edition cancels and replaces the second edition (ISO 6361-4:2011), which has been technically revised.ISO 6361 consists of the following parts, un
16、der the general title Wrought aluminium and aluminium alloys Sheets, strips and plates: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Strips: Tolerances on shape and dimensions Part 4: Sheets and plates: Tolerances on shape and dimensions Part 5: Chem
17、ical compositioniv ISO 2014 All rights reservedBS ISO 6361-4:2014INTERNATIONAL STANDARD ISO 6361-4:2014(E)Wrought aluminium and aluminium alloys Sheets, strips and plates Part 4: Sheets and plates: Tolerances on shape and dimensions1 ScopeThis part of ISO 6361 specifies the tolerances on shape and d
18、imensions for wrought aluminium and aluminium alloy sheet and plate by hot-rolling or cold-rolling for general engineering applications.It applies to products with a thickness over 0,15 mm up to and including 203 mm.It does not apply to semi-finished rolled products in coiled form to be subjected to
19、 further rolling (reroll stock) or to special products, such as those that are corrugated or embossed.Technical conditions for inspection and delivery of products covered by this part of ISO 6361 are specified in ISO 6361-1.2 Normative referencesNo normative references cited in this document.3 Dimen
20、sional tolerances3.1 ThicknessThickness tolerances for a cold-rolled product are specified in Table 1 and Table 2.Thickness tolerances for a hot-rolled product are specified in Table 3 and Table 4.When the tolerance is specified as either all plus or minus side, the value in Table 1, Table 2, Table
21、3, or Table 4 shall be doubled.Tolerances for the products exceeding the range of specified thickness and width shall be agreed upon between the purchaser and the supplier.Table 1 Thickness tolerances for cold-rolled productDimensions in millimetresSpecified thicknessAlloy number1050, 1050A, 1070, 1
22、070A,1080, 1080A, 1085, 1100, 1100A, 1200, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A, 8021, 8079Specified widthOverUp to and includingUp to and including 450Over 450, up to and including 900Over 900, up to and including 1 400Over 1 400, up to and including
23、 1 800Over 1 800, up to and including 2 300Over 2 300, up to and includ-ing 2 600Tolerance0,15 0,20 0,03 0,03 0,05 ISO 2014 All rights reserved 1BS ISO 6361-4:2014ISO 6361-4:2014(E)Specified thicknessAlloy number1050, 1050A, 1070, 1070A,1080, 1080A, 1085, 1100, 1100A, 1200, 1230A, 3003, 3103, 3203,
24、3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A, 8021, 8079Specified widthOverUp to and includingUp to and including 450Over 450, up to and including 900Over 900, up to and including 1 400Over 1 400, up to and including 1 800Over 1 800, up to and including 2 300Over 2 300, up to and inc
25、lud-ing 2 600Tolerance0,20 0,25 0,03 0,04 0,05 0,25 0,45 0,04 0,04 0,05 0,06 0,45 0,70 0,04 0,05 0,06 0,08 0,70 0,90 0,05 0,05 0,06 0,09 0,13 0,90 1,1 0,05 0,06 0,08 0,10 0,13 1,1 1,7 0,06 0,08 0,10 0,13 0,15 1,7 1,9 0,06 0,08 0,10 0,15 0,20 1,9 2,4 0,08 0,08 0,10 0,15 0,20 2,4 2,7 0,09 0,10 0,13 0,
26、18 0,23 2,7 3,6 0,11 0,11 0,13 0,18 0,23 0,253,6 4,5 0,15 0,15 0,20 0,23 0,28 0,304,5 5,0 0,18 0,18 0,23 0,28 0,33 0,385,0 6,5 0,23 0,23 0,28 0,33 0,38 0,436,5 8,0 0,33 0,33 0,33 0,38 0,43 0,518,0 11 0,48 0,48 0,48 0,48 0,58 0,6611 16 0,64 0,64 0,64 0,64 0,76 0,89Table 2 Thickness tolerances for col
27、d-rolled productDimensions in millimetresSpecified thicknessAlloy number2014, 2014A, 2017, 2017A, 2618A, 2219, 2024, 2124, 3004, 3104, 5021, 5026, 5040, 5042, 5049, 5449, 5251, 5052, 5154, 5154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 6061, 6082, 7204, 7010, 70
28、20, 7021, 7022, 7050, 7075, 7475, 7178Specified widthOverUp to and includ-ingUp to and includ-ing 450Over 450, up to and includ-ing 900Over 900, up to and includ-ing 1 200Over 1 200, up to and includ-ing 1 400Over 1 400, up to and includ-ing 1 500Over 1 500, up to and includ-ing 1 700Over 1 700, up
29、to and includ-ing 1 800Over 1 800, up to and includ-ing 2 000Over 2 000, up to and includ-ing 2 100Over 2 100, up to and includ-ing 2 300Over 2 300, up to and includ-ing 2 400Over 2 400, up to and includ-ing 2 600Tolerance0,20 0,25 0,03 0,04 0,06 0,06 0,25 0,45 0,04 0,04 0,06 0,09 0,45 0,70 0,04 0,0
30、5 0,06 0,09 0,10 0,10 0,10 0,70 0,90 0,05 0,05 0,06 0,10 0,13 0,13 0,13 0,15 0,90 1,1 0,05 0,06 0,08 0,10 0,13 0,13 0,13 0,15 1,1 1,7 0,06 0,08 0,10 0,13 0,15 0,15 0,15 0,18 1,7 1,9 0,08 0,08 0,10 0,13 0,15 0,15 0,15 0,18 1,9 2,4 0,09 0,09 0,10 0,13 0,15 0,15 0,15 0,18 0,18 0,30 Table 1 (continued)2
31、 ISO 2014 All rights reservedBS ISO 6361-4:2014ISO 6361-4:2014(E)Specified thicknessAlloy number2014, 2014A, 2017, 2017A, 2618A, 2219, 2024, 2124, 3004, 3104, 5021, 5026, 5040, 5042, 5049, 5449, 5251, 5052, 5154, 5154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 60
32、61, 6082, 7204, 7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178Specified widthOverUp to and includ-ingUp to and includ-ing 450Over 450, up to and includ-ing 900Over 900, up to and includ-ing 1 200Over 1 200, up to and includ-ing 1 400Over 1 400, up to and includ-ing 1 500Over 1 500, up to and includ-
33、ing 1 700Over 1 700, up to and includ-ing 1 800Over 1 800, up to and includ-ing 2 000Over 2 000, up to and includ-ing 2 100Over 2 100, up to and includ-ing 2 300Over 2 300, up to and includ-ing 2 400Over 2 400, up to and includ-ing 2 600Tolerance2,4 2,7 0,10 0,10 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0
34、,41 2,7 3,2 0,11 0,11 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0,41 0,46 0,513,2 3,6 0,11 0,11 0,13 0,13 0,18 0,25 0,30 0,33 0,36 0,41 0,46 0,513,6 4,5 0,15 0,15 0,20 0,20 0,23 0,30 0,36 0,38 0,41 0,43 0,48 0,584,5 5,0 0,18 0,18 0,25 0,25 0,28 0,36 0,41 0,43 0,43 0,43 0,56 0,665,0 6,5 0,23 0,23 0,28 0,28
35、0,33 0,41 0,46 0,46 0,46 0,46 0,61 0,716,5 8,0 0,33 0,33 0,33 0,33 0,38 0,46 0,51 0,51 0,51 0,51 0,64 0,768,0 11 0,48 0,48 0,48 0,48 0,51 0,51 0,58 0,58 0,64 0,64 0,66 0,8411 16 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,76 0,76 0,76 0,89 0,89Table 3 Thickness tolerances for hot-rolled productDimensions i
36、n millimetresSpecified thicknessAlloy number1050, 1050A, 1070, 1070A, 1080, 1080A, 1085,1100, 1100A, 1200, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011ASpecified widthOverUp to and includingUp to and including 900Over 900, up to and including 1 400Over 1 400,
37、up to and including 1 800Over 1 800, up to and including 2 300Over 2 300, up to and including 2 600Over 2 600, up to and including 3 400Tolerance4 5 0,25 0,30 0,35 0,40 5 6 0,30 0,40 0,45 0,50 6 8 0,45 0,45 0,55 0,65 0,75 0,858 11 0,55 0,55 0,65 0,75 0,85 0,9511 16 0,65 0,65 0,75 0,85 0,95 1,016 22
38、0,80 0,80 0,80 0,90 1,1 1,122 29 0,90 0,90 0,90 1,1 1,4 1,429 35 1,0 1,0 1,0 1,3 1,7 1,735 40 1,1 1,1 1,1 1,5 1,9 1,940 50 1,3 1,3 1,3 1,8 2,2 2,250 55 1,5 1,5 1,5 2,0 2,5 2,5NOTE This specification shall be applied to the products of temper grade H112 and those finished by the hot-rolled condition.
39、Table 2 (continued) ISO 2014 All rights reserved 3BS ISO 6361-4:2014ISO 6361-4:2014(E)Specified thicknessAlloy number1050, 1050A, 1070, 1070A, 1080, 1080A, 1085,1100, 1100A, 1200, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011ASpecified widthOverUp to and includ
40、ingUp to and including 900Over 900, up to and including 1 400Over 1 400, up to and including 1 800Over 1 800, up to and including 2 300Over 2 300, up to and including 2 600Over 2 600, up to and including 3 400Tolerance55 70 1,9 1,9 1,9 2,5 3,2 3,270 75 2,3 2,3 2,3 3,0 3,8 3,875 100 2,8 2,8 2,8 3,6 4
41、,1 4,1100 150 3,2 3,2 3,8 4,1 150 203 4,1 4,1 4,1 4,1 NOTE This specification shall be applied to the products of temper grade H112 and those finished by the hot-rolled condition.Table 4 Thickness tolerances for hot-rolled productDimensions in millimetresSpecified thicknessAlloy number2014, 2014A, 2
42、017, 2017A, 2618A, 2219, 2024, 2124, 3004, 3104, 5021, 5026, 5040, 5042, 5049, 5449, 5251, 5052, 5154, 5154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 6061, 6082, 7204,7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178Specified widthOverUp to and includingUp to and i
43、ncluding 900Over 900, up to and including 1 400Over 1 400, up to and including 1 800Over 1 800, up to and including 2 300Over 2 300, up to and including 2 600Over 2 600, up to and including 3 400Tolerance4 5 0,30 0,35 0,50 0,60 5 6 0,40 0,45 0,55 0,65 6 8 0,50 0,50 0,60 0,70 0,80 0,908 11 0,60 0,60
44、0,70 0,80 0,90 1,011 16 0,70 0,70 0,80 0,90 1,0 1,116 22 0,80 0,80 0,80 0,90 1,1 1,122 29 0,90 0,90 0,90 1,1 1,4 1,429 35 1,0 1,0 1,0 1,3 1,7 1,735 40 1,1 1,1 1,1 1,5 1,9 1,940 50 1,3 1,3 1,3 1,8 2,2 2,250 55 1,5 1,5 1,5 2,0 2,5 2,555 70 1,9 1,9 1,9 2,5 3,2 3,270 75 2,3 2,3 2,3 3,0 3,8 3,8NOTE This
45、specification shall be applied to the products of temper grade H112 and those finished by the hot-rolled condition.Table 3 (continued)4 ISO 2014 All rights reservedBS ISO 6361-4:2014ISO 6361-4:2014(E)Specified thicknessAlloy number2014, 2014A, 2017, 2017A, 2618A, 2219, 2024, 2124, 3004, 3104, 5021,
46、5026, 5040, 5042, 5049, 5449, 5251, 5052, 5154, 5154A, 5254, 5454, 5754, 5456, 5059, 5070, 5082, 5182, 5083, 5383, 5086, 6016, 6025, 6061, 6082, 7204,7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178Specified widthOverUp to and includingUp to and including 900Over 900, up to and including 1 400Over 1 4
47、00, up to and including 1 800Over 1 800, up to and including 2 300Over 2 300, up to and including 2 600Over 2 600, up to and including 3 400Tolerance75 100 2,8 2,8 2,8 3,6 4,1 4,1100 150 3,2 3,2 3,6 4,1 4,1150 203 4,1 4,1 4,1 4,1 4,1NOTE This specification shall be applied to the products of temper
48、grade H112 and those finished by the hot-rolled condition.3.2 WidthWidth tolerances for shared sheet and plate are specified in Table 5.Width tolerances for sawed sheet and plate are specified in Table 6.Width is measured at room temperature during cutting. The allowable maximum deviation shall be 0,23 mm per 1 000 mm in width, by a temperature difference of 10 C aga
