1、Shipbuilding Deck machinery Warping end profilesBS ISO 6482:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Shipbuilding Deck machinery Warping end profilesConstruction navale Auxiliaires de pont Profils de poupeINTERNATIONAL STANDARDISO6482Second editio
2、n2017-05Reference numberISO 6482:2017(E)National forewordThis British Standard is the UK implementation of ISO 6482:2017.The UK participation in its preparation was entrusted to Technical Committee SME/32, Ships and marine technology - Steering committee.A list of organizations represented on this c
3、ommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 89811 2ICS 47.
4、020.50Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS ISO 6482:20
5、17 ISO 2017Shipbuilding Deck machinery Warping end profilesConstruction navale Auxiliaires de pont Profils de poupeINTERNATIONAL STANDARDISO6482Second edition2017-05Reference numberISO 6482:2017(E)BS ISO 6482:2017ISO 6482:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, P
6、ublished in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Perm
7、ission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 6482:2017ISO 6482:2017(E)ii IS
8、O 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on t
9、he internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09
10、47copyrightiso.orgwww.iso.orgISO 6482:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Types, nominal sizes and dimensions 14.1 Types 14.2 Nominal sizes and dimensions 15 Relation between warping end dimensions and rope sizes 35.1 Proportional relation between warpin
11、g end lengths and selected rope sizes . 35.2 Proportional relation between warping end diameters and selected rope sizes 36 Calculation of warping end shaft torque and bending moment 36.1 Calculated position of maximum torque. 36.2 Calculated position of bending moment at maximum torque 37 Dimension
12、al tolerances and surface roughness 48 Designation 4 ISO 2017 All rights reserved iiiContents PageBS ISO 6482:2017ISO 6482:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Interna
13、tional Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with
14、ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, P
15、art 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of
16、the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations
17、 received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assess
18、ment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and
19、 deck machinery.This second edition cancels and replaces the first edition (ISO 6482:1980), which has been technically revised.This edition revises the type, nominal dimensions, relation between nominal dimensions and rope sizes of warping ends, cancels the part related to hole and rope hooks, and a
20、dds some requirements on manufacturing quality.iv ISO 2017 All rights reservedBS ISO 6482:2017ISO 6482:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is
21、normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part
22、in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular
23、 the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this
24、 document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .
25、iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as inf
26、ormation about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck machinery.This
27、 second edition cancels and replaces the first edition (ISO 6482:1980), which has been technically revised.This edition revises the type, nominal dimensions, relation between nominal dimensions and rope sizes of warping ends, cancels the part related to hole and rope hooks, and adds some requirement
28、s on manufacturing quality.iv ISO 2017 All rights reserved INTERNATIONAL STANDARD ISO 6482:2017(E)Shipbuilding Deck machinery Warping end profiles1 ScopeThis document specifies the types, nominal sizes, dimensions, markings and selection rules of warping end profiles.The warping end specified in thi
29、s document is applicable to windlasses, mooring winches, capstans and other deck machinery with steel wire rope, and ropes of natural and man-made fibre.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements
30、of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 8062-3, Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 3: Gener
31、al dimensional and geometrical tolerances and machining allowances for castings3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 3828 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electrop
32、edia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 Types, nominal sizes and dimensions4.1 TypesThe document specifies two types of warping end profiles, as shown in Figure 1, namely:a) Type C Common;b) Type E Elongated.4.2
33、Nominal sizes and dimensionsThe nominal sizes and physical dimensions of the warping end are given in Figure 1 and Table 1. ISO 2017 All rights reserved 1BS ISO 6482:2017ISO 6482:2017(E)KeyC Profile type CE Profile type EA Winch sideFigure 1 Profile typesTable 1 Nominal sizes and physical dimensions
34、Dimensions in millimetresNominal sizeDLength of warping endL1L2RR1R2C1C2Type C (LC)Type E (LE)180 180 225 112 45 500 50 25 50 28200 200 250 125 50 560 56 28 56 32225 225 280 140 56 630 63 32 63 36250 250 315 160 63 710 71 36 71 40280 280 360 180 71 800 80 40 80 45315 315 400 200 80 900 90 45 90 5036
35、0 360 450 225 90 1 000 100 50 100 56400 400 500 250 100 1 120 112 56 112 63450 450 560 280 112 1 250 125 63 125 71500 500 630 315 125 1 400 140 71 140 80560 560 700 360 140 1 600 160 80 160 90630 630 800 400 160 1 800 180 90 180 100710 710 900 450 178 2 000 200 100 200 112800 800 500 2 250 225 112 2
36、25 125900 900 560 2 550 255 128 255 1441 000 1 000 630 2 850 285 143 285 160NOTE For the warping end which has special requirements for length, dimensions LC, LEand L2may be determined by design engineers or in the contract.2 ISO 2017 All rights reservedBS ISO 6482:2017ISO 6482:2017(E)KeyC Profile t
37、ype CE Profile type EA Winch sideFigure 1 Profile typesTable 1 Nominal sizes and physical dimensionsDimensions in millimetresNominal sizeDLength of warping endL1L2RR1R2C1C2Type C (LC)Type E (LE)180 180 225 112 45 500 50 25 50 28200 200 250 125 50 560 56 28 56 32225 225 280 140 56 630 63 32 63 36250
38、250 315 160 63 710 71 36 71 40280 280 360 180 71 800 80 40 80 45315 315 400 200 80 900 90 45 90 50360 360 450 225 90 1 000 100 50 100 56400 400 500 250 100 1 120 112 56 112 63450 450 560 280 112 1 250 125 63 125 71500 500 630 315 125 1 400 140 71 140 80560 560 700 360 140 1 600 160 80 160 90630 630
39、800 400 160 1 800 180 90 180 100710 710 900 450 178 2 000 200 100 200 112800 800 500 2 250 225 112 225 125900 900 560 2 550 255 128 255 1441 000 1 000 630 2 850 285 143 285 160NOTE For the warping end which has special requirements for length, dimensions LC, LEand L2may be determined by design engin
40、eers or in the contract.2 ISO 2017 All rights reserved ISO 6482:2017(E)5 Relation between warping end dimensions and rope sizes5.1 Proportional relation between warping end lengths and selected rope sizesThe proportional relation between warping end lengths LC, LEand selected rope diameter d must be
41、 met as follows: steel wire rope: Ld10 natural fibre rope and man-made fibre rope: Ld75,5.2 Proportional relation between warping end diameters and selected rope sizesThe proportional relation between warping end diameter D and selected rope diameter d must be met as follows: steel wire rope: Dd16 n
42、atural fibre rope and man-made fibre rope: Dd66 Calculation of warping end shaft torque and bending moment6.1 Calculated position of maximum torqueThe maximum shaft torque shall be calculated with dimension Crgiven by the following formula when calculating the shaft torque of the warping end (see Fi
43、gure 2).Cdr=075, (1)6.2 Calculated position of bending moment at maximum torqueThe maximum bending moment shall be calculated with dimension Lrgiven by the following formula when calculating the bending moment at the maximum shaft torque of the warping end:Ldr=117, (2)Figure 2 Calculating chart of o
44、utput shaft torque and bending moment of warping end ISO 2017 All rights reserved 3BS ISO 6482:2017ISO 6482:2017(E)7 Dimensional tolerances and surface roughness7.1 Linear casting dimensional tolerances shall comply with ISO 8062-3 DCTG 11.7.2 The surface roughness of the warping end shall be determ
45、ined by design according to the characteristics of ropes and materials of the warping end, or defined in the contract.8 DesignationThe warping end profile conforming to this document shall be designated in the following order:EXAMPLE For the designation of a warping end according to ISO 6482, with e
46、longated length and nominal size D = 630 mm:Warping end ISO 6482-0630-LE4 ISO 2017 All rights reservedBS ISO 6482:2017ISO 6482:2017(E)7 Dimensional tolerances and surface roughness7.1 Linear casting dimensional tolerances shall comply with ISO 8062-3 DCTG 11.7.2 The surface roughness of the warping
47、end shall be determined by design according to the characteristics of ropes and materials of the warping end, or defined in the contract.8 DesignationThe warping end profile conforming to this document shall be designated in the following order:EXAMPLE For the designation of a warping end according
48、to ISO 6482, with elongated length and nominal size D = 630 mm:Warping end ISO 6482-0630-LE4 ISO 2017 All rights reservedBS ISO 6482:2017ISO 6482:2017(E) ISO 2017 All rights reservedICS 47.020.50Price based on 4 pagesBS ISO 6482:2017This page deliberately left blankBSI is the national body responsib
49、le for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards h
