1、BRITISH STANDARDBS ISO 8279:2008Aerospace Nuts, hexagonal, plain, normal height, normal across flats, with MJ threads, classifications: 600 MPa (at ambient temperature)/120 C, 600 MPa (at ambient temperature)/235 C, 900 MPa (at ambient temperature)/ 425 C, 1 100 MPa (at ambient temperature)/235 C, 1
2、 100 MPa (at ambient temperature)/315 C, 1 100 MPa (at ambient temperature)/650 C, 1 210 MPa (at ambient temperature)/730 C, 1 250 MPa (at ambient temperature)/235 C and 1 550 MPa (at ambient temperature)/600 C Dimensions ICS 49.030.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3
3、g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS ISO 8279:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2008 BSI 2008ISBN 978 0 580 55
4、022 5National forewordThis British Standard is the UK implementation of ISO 8279:2008. It supersedes BS A317:1997 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on
5、this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda
6、 issued since publicationDate CommentsReference numberISO 8279:2008(E)INTERNATIONAL STANDARD ISO8279Third edition2008-08-01Aerospace Nuts, hexagonal, plain, normal height, normal across flats, with MJ threads, classifications: 600 MPa (at ambient temperature)/120 C, 600 MPa (at ambient temperature)/
7、235 C, 900 MPa (at ambient temperature)/425 C, 1 100 MPa (at ambient temperature)/235 C, 1 100 MPa (at ambient temperature)/315 C, 1 100 MPa (at ambient temperature)/650 C, 1 210 MPa (at ambient temperature)/730 C, 1 250 MPa (at ambient temperature)/235 C and 1 550 MPa (at ambient temperature)/600 C
8、 Dimensions Aronautique et espace crous hexagonaux ordinaires, hauteur normale, surplats normaux, filetages MJ, classifications: 600 MPa ( temprature ambiante)/120 C, 600 MPa ( temprature ambiante)/235 C, 900 MPa ( temprature ambiante)/425 C, 1 100 MPa ( temprature ambiante)/235 C, 1 100 MPa ( tempr
9、ature ambiante)/315 C, 1 100 MPa ( temprature ambiante)/650 C, 1 210 MPa ( temprature ambiante)/730 C, 1 250 MPa ( temprature ambiante)/235 C et 1 550 MPa ( temprature ambiante)/600 C Dimensions BS ISO 8279:2008ii iiiForeword ISO (the International Organization for Standardization) is a worldwide fe
10、deration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that com
11、mittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accord
12、ance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard require
13、s approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8279 was prepared by Technical C
14、ommittee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 4, Aerospace fastener systems. This third edition cancels and replaces the second edition (ISO 8279:1997), which has been technically revised. BS ISO 8279:2008iv Introduction The dimensions specified in this International Standard have
15、 been determined to satisfy the requirements of the procurement specification ISO 9139. BS ISO 8279:20081Aerospace Nuts, hexagonal, plain, normal height, normal across flats, with MJ threads, classifications: 600 MPa (at ambient temperature)/120 C, 600 MPa (at ambient temperature)/235 C, 900 MPa (at
16、 ambient temperature)/425 C, 1 100 MPa (at ambient temperature)/235 C, 1 100 MPa (at ambient temperature)/315 C, 1 100 MPa (at ambient temperature)/650 C, 1 210 MPa (at ambient temperature)/730 C, 1 250 MPa (at ambient temperature)/235 C and 1 550 MPa (at ambient temperature)/600 C Dimensions 1 Scop
17、e This International Standard specifies the dimensions of plain, hexagonal nuts, of normal height, normal across flats, with MJ threads, of classifications: 600 MPa1)/120 C2), 600 MPa1)/235 C2), 900 MPa1)/425 C2), 1 100 MPa1)/235 C2), 1 100 MPa1)/315 C2), 1 100 MPa1)/650 C2), 1 210 MPa1)/730 C2), 1
18、250 MPa1)/235 C2) and 1 550 MPa1)/600 C2). Nuts provided with holes are intended to be used with lockwire in conformity with ISO 245. This International Standard is only applicable for the compilation of aerospace product standards. 2 Normative references The following referenced documents are indis
19、pensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 245, Aerospace Lockwire Diameters ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensio
20、ns for bolts and nuts ISO 8788, Aerospace Nuts, metric Tolerances of form and position 1) Corresponds to the minimum tensile stress that the nut is able to withstand at ambient temperature, without breaking or cracking, when tested with a bolt of a higher strength class. 2) Maximum temperature that
21、the nut is able to withstand, without permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the material or by the surface treatment. BS ISO 8279:20082 3 Configuration and dimensions See Figure 1 and Table 1. Dime
22、nsions and tolerances are expressed in millimetres. They apply after any surface coating(s), but before the application of any lubricant. Dimensions in millimetres Tolerances of form and position shall conform to those specified in ISO 8788. Details of form not stated are left to the manufacturers d
23、iscretion. Key 1 two holes diameter U, optional 2 thread aThese values, in micrometres, apply before any surface coating(s) is(are) applied. The values do not apply to threads whose surface texture will be as achieved by the usual manufacturing methods. bAll forms of entry (chamfer or radius) permis
24、sible within these limiting dimensions. cForm of contour, within limiting dimensions, is left to the manufacturers discretion. Diameter M may be tangential to, but shall not intrude on, the flats. dTo both faces. eFrom one face. Figure 1 BS ISO 8279:20083Table 1 L M U E F H N V W Dia-meter code Thre
25、ad anom. tol. min. H13 min. nom. tol. h14 nom. tol. 0,2 min.Lockwire diameterb020 MJ2 0,4-4H6H 2,2 3,4 4,2 4 1,6 025 MJ2,5 0,45-4H6H 2,7 4,4 5,3 5 2 030 MJ3 0,5-4H6H 3,2 5,4 6,5 6 2,4 0,4 02040 MJ4 0,7-4H6H 4,2 6,4 7,6 7 3,2 050 MJ5 0,8-4H6H 5,2 0,60+7,4 8,7 8 h12 4 060 MJ6 1-4H5H 6,3 9,3 10,9 10 4,
26、8 3,9 2 070 MJ7 1-4H5H 7,3 10,2 12 11 5,6 4,4 2,4 080 MJ8 1-4H5H 8,3 12,21 14,3 13 6,4 0,5 5 2,8 0,8 100 MJ10 1,25-4H5H 10,3 16 18,9 17 8 6,9 3,6 120 MJ12 1,25-4H5H 12,3 18 21,1 19 9,6 8 4,4 140 MJ14 1,5-4H5H 14,4 21 24,5 22 11,2 9,6 5,1 160 MJ16 1,5-4H5H 16,4 23 26,8 24 12,8 10,7 5,9 180 MJ18 1,5-4
27、H5H 18,4 26 30,2 27 14,4 12 6,7 200 MJ20 1,5-4H5H 20,4 29 33,6 30 16 13,4 7,5 220 MJ22 1,5-4H5H 22,4 30,9 35,8 32 17,6 14,4 8,3 240 MJ24 2-4H5H 24,5 0,80+34,91,5 40,4 36 h13 19,20,6 0316,1 9,1 1,25 aIn accordance with ISO 5855-2. bFor information, in conformity with ISO 245. BS ISO 8279:20084 Biblio
28、graphy 1 ISO 9139, Aerospace Nuts, plain or slotted (castellated) Procurement specification 2 ISO 13715, Technical drawings Edges of undefined shape Vocabulary and indications BS ISO 8279:2008blankBS ISO 8279:2008BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fa
29、x +44 (0)20 8996 Standards Institution (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or rev
30、ision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform t
31、he Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions o
32、f standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to
33、orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Libr
34、ary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date
35、 with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British
36、Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyrig
37、ht, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the st
38、andard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email:
