1、BRITISH STANDARD BS QC 300200:1983 IEC 384-15: 1982 QC 300200: 1982 Incorporating Amendment No. 1 Harmonized system of quality assessment for electronic components Fixedcapacitors for use in electronic equipment Sectional specification: Fixed tantalum capacitors with solid or non-solid electrolyte I
2、EC title. Fixed capacitors for use in electronic equipment Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte UDC 621.319.4:621.38BSQC300200:1983 This British Standard, having been prepared under the directionof the Electronic Components Standards Committ
3、ee, was published underthe authority of the BoardofBSI and comes intoeffecton 31October1983 BSI 04-2000 The following BSI references relate to the work on this standard: Committee reference ECL/4 Draft for comment 79/26456 DC ISBN 0 580 13411 3 Committees responsible for this standard The preparatio
4、n of this British Standard was entrusted by the Electronic Components Standards Committee (ECL/-) to Technical Committee ECL/4 upon which the following bodies were represented: British Telecommunications Electronic Components Industry Federation Electronic Engineering Association Ministry of Defence
5、 National Supervising Inspectorate Society of British Aerospace Companies Limited Telecommunication Engineering and Manufacturing Association (TEMA) Amendments issued since publication Amd. No. Date of issue Comments 5950 July 1992 Indicated by a sideline in the marginBSQC300200:1983 BSI 04-2000 i C
6、ontents Page Committees responsible Inside front cover National foreword ii Section 1. General 1.1 Scope 1 1.2 Object 1 1.3 Related documents 1 1.4 Information to be given in a detail specification 1 1.5 Terminology 2 1.6 Marking 3 Section 2. Preferred ratings and characteristics 2.1 Preferred chara
7、cteristics 3 2.2 Preferred values of ratings 4 Section 3. Quality assessment procedures 3.1 Primary Stage of Manufacture 4 3.2 Structurally Similar Components 4 3.3 Certified Records of Released Lots 4 3.4 Qualification Approval 4 3.5 Quality Conformance Inspection 13 Section 4. Test and measurement
8、 procedures 4.1 Visual examination and check of dimensions 15 4.2 Electrical tests 15 4.3 Robustness of terminations 16 4.4 Resistance to soldering heat 17 4.5 Solderability 18 4.6 Rapid change of temperature 18 4.7 Vibration 18 4.8 Bump 18 4.9 Shock 19 4.10 Climatic sequence 19 4.11 Damp heat, stea
9、dy state 20 4.12 Endurance 20 4.13 Surge 20 4.14 Reverse voltage 21 4.15 Characteristics at high and low temperature 21 4.16 Charge and discharge 21 Figure 1 17 Table I Sampling plan together with numbers of permissible defectives for qualification approval tests 6 Table II Test schedule for Qualifi
10、cation Approval 7 Table IIIA 14 Table IIIB 14 Publications referred to Inside back coverBSQC300200:1983 ii BSI 04-2000 National foreword This British Standard has been prepared under the direction of the Electronic Components Standards Committee. It is identical with IEC Publication384-15QC 300200 “
11、Fixed capacitors for use in electronic equipment. Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte”, published in1982 by the International Electrotechnical Commission (IEC). This standard is a harmonized specification within the IECQ system of quality a
12、ssessment for electronic components. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention i
13、s drawn especially to the following. For the purposes of this British Standard 1.1 and 1.2 should be regarded as constituting the scope of the standard. Cross-references. The British Standard which implements QC001001and QC001002is BS9000“General requirements for a system for electronic components o
14、f assessed quality” Part 3:1991 “Specification for the national implementation of the IECQ system”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard
15、does not of itself confer immunity from legal obligations. International Standard Corresponding British Standard ISO 3:1973 BS 2045:1965 Preferred numbers (Technically equivalent) IEC 62:1974 BS 1852:1975 Marking codes for resistors and capacitors (Identical) IEC 63:1963 BS 2488:1966 Schedule of pre
16、ferred numbers for the resistance of resistors and the capacitance of capacitors for telecommunication equipment (Technically equivalent) IEC 68 BS 2011 Basic environmental testing procedures IEC 68-1:1982 Part 1.1:1983 General and guidance (Identical) IEC 384-1:1982 (QC 300000:1982) BS QC 300000:19
17、83 Fixed capacitors for use in electronic equipment Generic specification (Identical) IEC 410:1973 BS 6001 Sampling procedures and inspection by attributes Part 1:1991 Specification for sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection. Summary of pages This document
18、 comprises a front cover, an inside front cover, pages i and ii, pages1 to 22, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSQC300200:1983
19、BSI 04-2000 1 Section 1. General 1.1 Scope This standard applies to polar and bipolar tantalum electrolyte capacitors with solid and non-solid electrolyte for use in electronic equipment. It comprises capacitors for long-life applications and capacitors for general-purpose applications. Capacitors f
20、or special purpose application may need additional requirements. This standard covers three basic sub-families, namely: Sub-family 1: Fixed non-solid electrolyte tantalum capacitors with foil electrode. 1A: Plain foil electrode. 1B: Etched foil electrode. Sub-family 2: Fixed non-solid electrolyte ta
21、ntalum capacitors with porous anode. Sub-family 3: Fixed solid electrolyte tantalum capacitors with porous anode. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IECPublication384-1:1982, the appropriate quality assessment procedures, t
22、ests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal or higher performance level, because lower performance levels are not p
23、ermitted. 1.3 Related documents IEC publications. NOTEThe above references apply to the current editions except for IEC Publication 68, for which the referenced edition in the applicable test clauses of the generic specification shall be used. 1.4 Information to be given in a detail specification De
24、tail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in Sub-clause 1.9 of the
25、 detail specification and indicated in the test schedules, for example by an asterisk. NOTEThe information given in Sub-clause 1.4.1 may for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be sele
26、cted from those given in the appropriate clause of this sectional specification. Publication 62:1974: Marking Codes for Resistors and Capacitors. Publication 63:1963: Preferred Number Series for Resistors and Capacitors. Amendment No. 1 (1967). Amendment No. 2 (1977). Publication 68: Basic Environme
27、ntal Testing Procedures. Publication 384-1:1982: Fixed Capacitors for Use in Electronic Equipment. Part 1: Generic Specification. Publication 410:1973: Sampling Plans and Procedures for Inspection by Attributes. Publication QC 001001: 1981 Basic Rules of the IEC Quality Assessment System for Electro
28、nic Components (IECQ). Publication QC 001002: 1981 Rules of Procedure of the IEC Quality Assessment System for Electronic Components (IECQ). ISO Publication: ISO Standard 3: Preferred Numbers Series of Preferred Numbers.BSQC300200:1983 2 BSI 04-2000 1.4.1 Outline drawing and dimensions There shall b
29、e an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millime
30、tres, however when the original dimensions are given in inches, the converted metric dimensions in millimetres shall be added. Normally the numerical values shall be given for the length of the body, the width and height of the body and the wire spacing, or for cylindrical types, the body diameter,
31、and the length and diameter of the terminations. When necessary, for example when a number of items (capacitance values/voltage ranges) are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other
32、than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. 1.4.2 Mounting The detail specification shall spe
33、cify the method of mounting to be applied for normal use and for the application of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case, the deta
34、il specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. 1.4.3 Rating and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the followi
35、ng: 1.4.3.1 Rated capacitance range See Sub-clause 2.2.1. NOTEWhen products approved to the detail specification may have different ranges, the following statement should be added: “The range of values available in each voltage range is given in the qualified products list.” 1.4.3.2 Particular chara
36、cteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for design and application purposes. 1.4.3.3 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable for the solderability t
37、est and the resistance to soldering heat test. 1.4.4 Marking The detail specification shall specify the content of the marking on the capacitor and on the package. Deviations from Sub-clause 1.6 of this sectional specification, shall be specifically stated. 1.5 Terminology In addition to the applica
38、ble terms and definitions of IEC Publication384-1the following definitions apply: 1.5.1 capacitance of an electrolytic capacitor the capacitance of an equivalent circuit having capacitance and resistance in series measured with alternating current of approximately sinusoidal waveform of the specifie
39、d frequency 1.5.2 long-life grade capacitors capacitors intended for applications where a high degree of stability of characteristics over a long life is essential the materials are so chosen and manufacture so carried out that improved performance is obtained with consequent increase in lifeBSQC300
40、200:1983 BSI 04-2000 3 1.5.3 general-purpose grade capacitors capacitors intended for applications where the high performance level of long-life grade capacitors is not required 1.5.4 rated voltage (U R ) the maximum direct voltage which may be applied continuously to the terminations of a capacitor
41、 at the rated temperature NOTE 1The sum of the direct voltage and the peak alternating voltage applied to the capacitor shall not exceed the rated voltage. NOTE 2For short periods, however, the rated voltage may be exceeded (see Sub-clauses 2.2.6 and 4.13). 1.6 Marking According to Sub-clause 2.4 of
42、 IEC Publication 384-1, with the following details: 1.6.1 The information given in the marking is normally selected from the following list; the relative importance of each item is indicated by its position in the list: a) rated capacitance; b) rated voltage (d.c. voltage may be indicated by the sym
43、bolor); c) category voltage and category temperatures (for long-life grade capacitors only) (if applicable); d) polarity of the terminations: polar capacitors shall be marked with a positive sign near the positive terminations. Bipolar capacitors shall be marked positive at both ends and, if space p
44、ermits, in addition with the letters “BP”; e) tolerance on rated capacitance; f) reference to the grade. (For long-life grade capacitors only). The abbreviation “LL” may be used for marking purposes; g) year and month (or week) of manufacture; h) manufacturers name or trade mark; i) indication of th
45、e sub-family (e.g. 1, 2 or 3); j) climatic category; k) manufacturers type designation; l) reference to the detail specification. 1.6.2 The capacitor shall be clearly marked with a), b) and d) above and with as many as possible of the remaining items as is considered necessary. Any duplication of in
46、formation in the marking on the capacitor should be avoided. 1.6.3 The package containing the capacitor(s) shall be clearly marked with all the information listed in Sub-clause 1.6.1. 1.6.4 Any additional marking shall be so applied that no confusion can arise. Section 2. Preferred ratings and chara
47、cteristics 2.1 Preferred characteristics The values given in detail specifications shall preferably be selected from the following: 2.1.1 Preferred climatic categories The capacitors covered by this specification are classified into climatic categories according to the general rules given in IEC Pub
48、lication 68-1. The lower and upper category temperature and the duration of the damp heat, steady state test shall be chosen from the following: Lower category temperature: 55 C. Upper category temperature: + 85 C, + 100 C and + 125 C. Duration of the damp heat, steady state test: 4, 10, 21 and 56 d
49、ays.BSQC300200:1983 4 BSI 04-2000 The severities for the cold and dry heat tests are the lower and upper category temperatures respectively. 2.2 Preferred values of ratings 2.2.1 Rated capacitance (C R ) Preferred values of rated capacitance are chosen from the E3 series of IEC Publication63and their decimal multiples. If other values are needed, they shall preferably be chosen from the E6 series. 2.2.2 Tolerance on rated capacitance Preferred values of tolerances on rated capacitance are: 2.2.3 Rated voltage (U R ) Preferred values of rated direct volta
