CEN TS 13810-2-2003 Wood-based panels Floating floors Part 2 Test methods《木制板材 浮式地板 第2部分 试验方法》.pdf

上传人:unhappyhay135 文档编号:592438 上传时间:2018-12-16 格式:PDF 页数:18 大小:300.94KB
下载 相关 举报
CEN TS 13810-2-2003 Wood-based panels Floating floors Part 2 Test methods《木制板材 浮式地板 第2部分 试验方法》.pdf_第1页
第1页 / 共18页
CEN TS 13810-2-2003 Wood-based panels Floating floors Part 2 Test methods《木制板材 浮式地板 第2部分 试验方法》.pdf_第2页
第2页 / 共18页
CEN TS 13810-2-2003 Wood-based panels Floating floors Part 2 Test methods《木制板材 浮式地板 第2部分 试验方法》.pdf_第3页
第3页 / 共18页
CEN TS 13810-2-2003 Wood-based panels Floating floors Part 2 Test methods《木制板材 浮式地板 第2部分 试验方法》.pdf_第4页
第4页 / 共18页
CEN TS 13810-2-2003 Wood-based panels Floating floors Part 2 Test methods《木制板材 浮式地板 第2部分 试验方法》.pdf_第5页
第5页 / 共18页
亲,该文档总共18页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、DRAFT FOR DEVELOPMENT DD CEN/TS 13810-2:2003 Wood-based panels Floating floors Part 2: Test methods ICS 79.060.01 DD CEN/TS 13810-2:2003 This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 20 August 2003 BSI 20 August 2003 ISBN 0 580 42486 3

2、 National foreword This Draft for Development is the official English language version of CEN/TS 13810-2:2003. This publication is not to be regarded as a British Standard. It is being issued in the Draft for Development series of publications and is of a provisional nature because it is a new test

3、and there is insufficient experience of its use in the majority of CEN National Members. It should be applied on this provisional basis, so that information and experience of its practical application may be obtained. Comments arising from the use of this Draft for Development are requested so that

4、UK experience can be reported to the European organization responsible for its conversion to a European standard. A review of this publication will be initiated 2 years after its publication by the European organization so that a decision can be taken on its status at the end of its 3-year life. Not

5、ification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards. According to the replies received by the end of the review period, the responsible BSI Committee will decide whether to support the conversion into a European standard, to extend

6、 the life of the Technical Specification or to withdraw it. Comments should be sent in writing to the Secretary of BSI Technical Committee B/541, Wood-based panels, at British Standards House, 389 Chiswick High Road, London W4 4AL, giving the document reference and clause number and proposing, where

7、 possible, an appropriate revision of the text. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement European publications referred to in this document may be found in the BSI Catalogue under the sec

8、tion entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. Summary of pages This document comprises a front cover, an inside front cover, the CEN/TS title page, pages 2 to 15 and a back cover. The BS

9、I copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsTECHNICALSPECIFICATION SPCIFICATIONTECHNIQUE TECHNISCHESPEZIFIKATION CEN/TS138102 April2003 ICS79.060.01 Englishversion WoodbasedpanelsFloatingfloorsPart

10、2:Testmethods PanneauxbasedeboisPlanchersflottants Partie2:Mthodesdessai HolzwerkstoffeSchwimmendverlegteFubden Teil2:Prfverfahren ThisTechnicalSpecification(CEN/TS138102)wasapprovedbyCENon11November2002forprovisionalapplication. TheperiodofvalidityofthisCEN/TSislimitedinitiallytothreeyears.Aftertwo

11、yearsthemembersofCENwillberequested tosubmittheir comments,particularlyonthequestionwhethertheCEN/TScanbeconvertedintoaEuropeanStandard. CENmembersarerequiredtoannouncetheexistenceofthisCEN/TSinthesamewayasforanENandtomaketheCEN/TSavailable .It ispermissibletokeepconflictingnationalstandardsinforce(

12、inparalleltotheCEN/TS)untilthefinaldecisionaboutthep ossible conversionoftheCEN/TSintoanENisreached. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Hungary,Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain

13、,Sweden,SwitzerlandandUn ited Kingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2003CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.CEN/TS138102:2003ECEN

14、/TS138102:2003(E) 2 Contents page Foreword. 3 1 Scope 4 2 Normativereferences . 4 3 Termsanddefinitions. 4 4 Symbolsandsubscripts . 5 4.1 Symbols . 5 4.2 Subscripts 5 5 Principle . 5 6 Sampling 5 7 Testsetupandapparatus . 5 7.1 Testsetupforconcentratedpointloadandalternatingload 5 7.2 Testsetupforim

15、pactload . . 7 7.3 Apparatus. 7 7.3.1 Concentratedpointload. 7 7.3.2 Alternatingload . 7 7.3.3 Impactload . . 8 8 Deflectionmeasurement 8 8.1 Concentratedpointload. 8 8.2 Alternatingload . 8 8.3 Impactload . . 8 9 Preparationofthetestflooranddocumentationofmaterial . 8 9.1 Testfloor 8 9.2 Documentat

16、ionofmaterial. 8 10 Procedure. 9 10.1 Summaryoftheloadingandmeasurementprocedureforconcentratedandalternatingload . 9 10.1.1 Testsetup . 9 10.1.2 Preloading . 9 10.1.3 Referencedeflection. 9 10.1.4 Performancetesting . 10 10.1.5 Requirement 10 10.2 Positionofcarouselfordeflectionmeasurements . 10 10

17、.3 Measurementprocedureandrecords . 10 10.4 Impactloading. 11 11 Expressionofresults 11 11.1 Loadcategory 11 11.2 Concentratedpointload . 11 11.3 Alternatingload. 11 11.4 Impactload 11 12 Testreport 12 AnnexA (normative) Testsetupforpanelwidth800mm,900mmand1200mm 13CEN/TS138102:2003(E) 3 Foreword Th

18、isdocument(CEN/TS138102:2003)hasbeenpreparedbyTechnicalCommitteeCEN/TC112“Woodbased panels”,thesecretariatofwhichisheldbyDIN. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsofthefollowingcoun triesareboundtoannouncethisTechnicalSpecification:Austria,Belgium,CzechRepubl

19、ic,Denmark,Finland, France,Germany,Greece,Hungary,Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal, Slovakia,Spain,Sweden,SwitzerlandandtheUnitedKingdom. AnnexAisnormative.CEN/TS138102:2003(E) 4 1Scope ThisTechnicalSpecificationspecifiestestmethodsforloadingacontinuouslyfullysuppor

20、tednonstructuralfloating floorwithstaticconcentratedpointloads,alternatingloadsanddynamicimpactloadsfordeterminingthevaluesof theresultingdeflections. NOTE Thesetestmethodsformpartofthebasisforclassificationoffloatingfloorconstructions.Therequirements,i.e.load values,numberofloadcycles,anddeflection

21、limitsforthedifferentloadcategories,aregiveninEN138101. 2 Normativereferences ThisTechnicalSpecificationincorporatesbydatedorundatedreference,provisionsfromotherpublications.These normativereferencesarecitedattheappropriateplacesinthetext,andthepublicationsarelistedhereafter.For datedreferences,subs

22、equentamendmentstoorrevisionsoranyofthesepublicationsapplytothisTechnical Specificationonlywhenincorporatedinitbyamendmentorrevision.Forundatedreferences,thelatesteditionof thepublicationreferredtoapplies(includingamendments). EN310, WoodbasedpanelsDeterminationofmodulusofelasticityinbendingandofben

23、dingstrength. EN319, ParticleboardsandfibreboardsDeterminationoftensilestrengthperpendiculartotheplaneofthe board. EN322, WoodbasedpanelsDeterminationofmoisturecontent. EN323, WoodbasedpanelsDeterminationofdensity. EN3261, WoodbasedpanelsSampling,cuttingandinspectionPart1:Samplingandcuttingoftestpie

24、ces andexpressionoftestresults. EN826, ThermalinsulatingproductsforbuildingapplicationsDeterminationofcompressionbehaviour. EN1195, TimberstructuresTestmethodsPerformanceofstructuralfloordecking. EN1602, ThermalinsulatingproductsforbuildingapplicationsDeterminationoftheapparentdensity. EN199111, Eur

25、ocode1:Actions on structures Part11: General actions Densities, selfweight, imposed loadsforbuildings. EN138101, WoodbasedpanelsFloatingfloorsPerformancespecificationsandrequirements. 3 Termsanddefinitions ForthepurposesofthisTechnicalSpecificationthefollowingtermsanddefinitionsapply. 3.1 staticload

26、ing loadingsituationisdeemedtobestaticwhentheloadisconstantoveratleastaperiodof1h 3.2 alternatingload loadingsituationisdeemedtoalternatewhereitsmagnitudevariesinacyclicmannerwithtime 3.3 Tjoint jointbetweenthreefloorpanels 3.4 Ijoint jointbetweentwofloorpanelsCEN/TS138102:2003(E) 5 4 Symbolsandsubs

27、cripts 4.1Symbols x singlevaluefordeflectionoftheconcentratedload y singlevaluefordeflectionofimpact x meanvaluefordeflectionoftheconcentratedload n highestnumberofalternatingmeasurementpoint 4.2Subscripts 1to8 measurementpointforconcentratedpointload 9to14 measurementpointforalternatingload c resul

28、tofconcentratedpointload a resultofalternatingload im resultofimpactload i measurementnumber ref reference 5Principle Atestfloorissubjectstepwisetoaseriesofloadingseachstep,representingincreasingloadclassesin EN199111(Eurocode1).Foreachloadthedeflectionsaremeasured,andthetestfloorischeckedforvisible

29、 damage.Theperformanceofthefloatingfloorsystemisquantifiedasthehighestloadcategorytowhichthetest floorcanbesubjectedwithoutvisibledamageofthepanelorthejoints,andwithoutthedeflectionlimitsbeingex ceed. 6Sampling Panelsusedforboththetestfloorandthedummyunitshallbesampledfromproductionoveraperiodofatle

30、ast threeproductions. Thenumberoftestpanelsrequiredarerelatedtothedimensionsofthepanelsandthemeasurementrequired. Seefigure1and8.2. 7 Testsetupandapparatus 7.1 Testsetupforconcentratedpointloadandalternatingload Theconstructionofthetestfloorshallberepresentativeofthatoccurringinservice. Theprinciple

31、testsetupisshowninfigure1. Iftheflooringconsistsoffloorpanelsof600mmwidth,thejointlayoutandthelocationoftheconcentratedpoint loadandalternatingloadshallbeasshowninfigure1.CEN/TS138102:2003(E) 6 Iftheflooringconsistsoffloorpanelsof800mm,900mm,1000mmor1200mmwidth,thejointlayoutandthe locationoftheconc

32、entratedpointloadandalternatingloadshallbeasshowninthefiguresgiveninannexA. Dimensionsinmillimetres Key Paneljoint Locationofpointload Courseofwheel Measuringpoint Loadequipmentunit Figure1Testfloor,andlocationofloadequipmentandmeasuringpointsPanelwidth600mmCEN/TS138102:2003(E) 7 7.2 Testsetupforimp

33、actload TheimpacttestingcanbecarriedoutontheactualfloorsetupsatleastattwoTjoints,ifthishasnotbeen damaged.Alternatively,twoseparatetestsetupsshallbepreparedwithaminimumdimensionof1200mm 1200mm.EachofthetestsetupsshallcontainaTjoint,seefigure2. Dimensionsinmillimetres Key 1 Pointofimpact Figure2Tests

34、etupforimpactloadaccordingtoEN1195 7.3Apparatus 7.3.1 Concentratedpointload Concentratedpointloadshallbeappliedatthe16positions( )giveninfigure1orinannexA. Theconcentratedpointloadshallbeappliedthroughaflatsteelsurfacewithadiameterof(25 0,1)mmandwith theedgeofthecontactsurfaceroundedwitharadiusof2mm

35、. NOTE Theloadistransferredtothetestfloorbymeansofasteelbar. Fourpointloadsatthecornersofa300mm 900mmrectangleconstituteone“rack”,andtworacksarearranged ateachendofthefloor,shownasrectanglesinfigure1orannexA.Thedistancefromtheracktotheendofthe floorshallbe50mm. 7.3.2 Alternatingload Theequipmentfora

36、lternatingloadisacarousel,consistingofaplate(frame)withthreewheels,andamotordriven verticaldrivingshaftatthecentre. Thethreewheelsshallbelocatedatthecomersofanequilateraltriangle,andthediameterofthepathofthe middleofthewheelsshallbe(1700 50)mm.Thetyreofthewheelsshallbemadeofsolidrubberwithahard ness

37、of65to70ShoreA,andtheirdiametershallbe(200 25)mm.Thewidthofthewheelsshallbe(35 5)mm. Thetotalloadofthecarouselshallbeevenlydistributedoverthreewheels.Theaccuracyoftheloadshallbe 5%.Thespeedofrotationofthecarouselshallbe(10 0,5)min 1 . NOTE Thespeedofrotationcorrespondsto30loadcyclesperminuteoraloadf

38、requencyof0,5Hz.CEN/TS138102:2003(E) 8 7.3.3 Impactload TheloadequipmentshallbeinaccordancewithEN1195. 8 Deflectionmeasurement 8.1 Concentratedpointload Atthemeasuringpoints1,2,3and4(seefigure1andannexA)thedeflectionofthefloorsurfaceismeasuredas theverticalmovementofthecircularsteelbar.Atthemeasurin

39、gpoints5,6,7and8,whicharesituated300mm fromthemeasuringpoints1,2,3and4,thedeflectionofthefloorsurfaceismeasureddirectly. Thedeflectionsshallbemeasuredwithanaccuracyof 0,05mm. 8.2 Alternatingload Themeasuringpoints(seefigure1andannexA)roundthecarouselshallbelocatedasshowninfigure1,i.e.six measuringpo

40、ints,nos.9to14.Forpanelshavingawidthgreaterthan900mm,atleastfourmeasuringpointsshall belocatedaroundthecarousel,seeannexA.AtleasttwoofthesepointsshallbelocatedclosetoaTjoint,and theremainingpointsclosetoanIjoint.Allthemeasuringpointsshallbelocated150mmfromthepathofthe wheels.Thedeflectionsshallbemea

41、suredwithanaccuracyof 0,05mm. 8.3 Impactload Beforeimpactloadingthereferencedeflectionposition(y i,ref )ofthetopsideofthefloorismeasuredasthe verticalpositionofacircularsteelbar( e25mm)underaloadof1kN. After10impactsthedeflection( y im )ofthetopsideofthefloorismeasuredastheverticalmovementofthecircu

42、lar steelbar( e25mm)underaloadof1kN. Thedeflectionshallbemeasuredwithanaccuracyof 0,05mm. 9 Preparationofthetestflooranddocumentationofmaterial 9.1 Testfloor Thematerialsforthetestfloorandforthespecimensfortestingshallbeconditionedforatleastoneweekinthe laboratorybeforelaying.Therelativehumidityandt

43、emperatureinthelaboratoryshallberecorded. Thetestfloorshallbelaidonarigid,flatsurface(e.g.onaconcretefloor)withaflatnesstoleranceof1mm/2m. Thetestfloorshallbeconstructedwiththesamematerials,joints,flooringlayersandbeamsetc.whicharepre scribedforthefloatingfloorsystem.Thetestfloorshallhavetheminimumdimensions2400mm 3600mm.For actualdimensionsandjointlayout,seefigure1orannexA. Thetestfloorshallremainunloadedforatleast24hbeforetesting.Theperiodcanbelongerdepending

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1