1、TESTPDF*DEPARTMENT OF THE ARMY CEGS-10430 (June 1998)U.S. ARMY CORPS OF ENGINEERS -SupersedingCEGS-10430 (May 1995)GUIDE SPECIFICATION FOR CONSTRUCTIONIncludes changes through Notice 2 (October 2000)Includes Text Adjustment Change (October 1999)Includes Special Change (Submittal Paragraph)(June/Augu
2、st 2000)Latest change indicated by CHG tags*SECTION TABLE OF CONTENTSDIVISION 10 - SPECIALTIESSECTION 10430EXTERIOR SIGNAGE06/98PART 1 GENERAL1.1 REFERENCES1.2 GENERAL1.3 WIND LOAD REQUIREMENTS1.4 CHARACTER PROPORTIONS AND HEIGHTS1.5 SUBMITTALS1.6 QUALIFICATIONS1.7 DELIVERY AND STORAGE1.8 WARRANTY1.
3、9 EXTRA STOCKPART 2 PRODUCTS2.1 MODULAR EXTERIOR SIGNAGE SYSTEM2.1.1 Free-Standing Base Mount Pylon/Monolith Type Signs2.1.1.1 Framing2.1.1.2 Exterior Sheeting Panels2.1.1.3 Mounting2.1.1.4 Finishes2.1.2 Panel And Post/Panel Type Signs2.1.2.1 Posts2.1.2.2 Panel Framing System2.1.2.3 Panels2.1.2.4 Fi
4、nishes2.1.2.5 Mounting2.1.3 Changeable Letter Directories2.1.3.1 Frame and Trim2.1.3.2 Header Plates2.1.3.3 Door Glazing2.1.3.4 Door ConstructionSECTION 10430 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TESTPDF2.1.3.5 Door Locks2.1.3.6 Fabr
5、ication2.1.3.7 Finishes2.1.3.8 Mounting2.1.3.9 Changeable Letters2.2 ILLUMINATION2.3 GRAPHICS FOR EXTERIOR SIGNAGE SYSTEMS2.3.1 Graphics2.3.2 Messages2.4 METAL PLAQUES2.4.1 Cast Metal Plaques2.4.1.1 Fabrication2.4.1.2 Size2.4.1.3 Border2.4.1.4 Background2.4.1.5 Mounting2.4.1.6 Finish2.4.2 Chemically
6、 Etched Metal Plaques2.4.2.1 Fabrication2.4.2.2 Size2.4.2.3 Finish2.4.3 Frost and Surface Oxidized Plaques2.4.3.1 Fabrication2.4.3.2 Size2.4.3.3 Finish2.5 DIMENSIONAL BUILDING LETTERS2.5.1 Fabrication2.5.2 Typeface2.5.3 Size2.5.4 Finish2.5.5 Mounting2.6 ALUMINUM ALLOY PRODUCTS2.7 ANODIC COATING2.8 O
7、RGANIC COATING2.9 STEEL PRODUCTS2.10 CAST BRONZE2.11 VINYL SHEETING FOR GRAPHICS2.12 GLASS2.13 FIBER-REINFORCED POLYESTER (FRP) PANELS2.14 ACRYLIC SHEET2.15 POLYCARBONATE SHEET2.16 ANCHORS AND FASTENERS2.17 SHOP FABRICATION AND MANUFACTURE2.17.1 Factory Workmanship2.17.2 Dissimilar Materials2.17.3 S
8、hop Painting2.18 COLOR, FINISH, AND CONTRASTPART 3 EXECUTION3.1 INSTALLATION3.1.1 Anchorage3.1.2 Protection and Cleaning3.2 FIELD PAINTED FINISH- End of Section Table of Contents -SECTION 10430 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TE
9、STPDF*DEPARTMENT OF THE ARMY CEGS-10430 (June 1998)U.S. ARMY CORPS OF ENGINEERS -SupersedingCEGS-10430 (May 1995)GUIDE SPECIFICATION FOR CONSTRUCTIONIncludes changes through Notice 2 (October 2000)Includes Text Adjustment Change (October 1999)Includes Special Change (Submittal Paragraph)(June/August
10、 2000)Latest change indicated by CHG tags*SECTION 10430EXTERIOR SIGNAGE06/98*NOTE: This guide specification covers the requirements for common types of exterior signs, dimensional building letters, and metal plaques. This guide specification is to be used in the preparation of project specifications
11、 in accordance with ER 1110-1-8155. Comments and suggestions on this specification are welcome and should be directed to the proponent of the specification. A listing of proponents, including their organization designation and telephone number, is at URL: http:/www.hnd.usace.army.mil/techinfo/index.
12、htm, and an electronic feedback page for submission of recommended changes is available at the same address. Use of electronic communication is encouraged.*PART 1 GENERAL*NOTE: Facilities not excluded by TI 800-01 Design Criteria will be accessible in accordance with 36 CFR, Part 1191, Americans wit
13、h Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities.Drawings will indicate location, dimensions, elevations, schedules, content, details and such other information as required to indicate the extent of the work. The same terminology or titles used in the specification, for
14、 the different types of signage, will be used on the drawings and schedules.SECTION 10430 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TESTPDFDesigner must coordinate and incorporate existing signage policy and designs, as required, for new
15、projects on existing facilities.This section covers some of the more common exterior sign types. When other sign types are to be used, specifications will be modified accordingly.Product selections shall be based on aesthetic values, appearance, and cost as related to project needs.Additional Guidan
16、ce on the development of signage systems is available in USACE EP 310-1-6a and 6b, Sign Standards Manual. The document is available from the USACE Publications Depot, 2803 52nd Avenue, Hyattsville, MD 20781, 301-394-0081/82/83/84.*1.1 REFERENCES*NOTE: Issue (date) of references included in project s
17、pecifications need not be more current than provided by the latest change (Notice) to this guide specification.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to in the text by basic designation only.ALUMINUM ASSOCIATION (AA)AA
18、 DAF-45 (1997) Designation System for Aluminum FinishesAMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)ANSI Z97.1 (1984; Rev 1994) Safety Performance Specifications and Methods of Test for Safety Glazing Materials Used in BuildingsAMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)ASTM A 36/A 36M (1997ael
19、) Carbon Structural SteelASTM A 123/A 123M (1997ael) Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A 570/A 570M (1998) Steel, Sheet and Strip, Carbon, Hot-Rolled, Structural QualityASTM A 653/A 653M (1999a) Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvanne
20、aled) by the Hot-Dip ProcessSECTION 10430 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TESTPDFASTM A 924/A 924M (1999) General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip ProcessASTM B 26/B 26M (1999) Aluminum-Alloy Sand Cas
21、tingsASTM B 62 (1993) Composition Bronze or Ounce Metal CastingsASTM B 108 (1999) Aluminum-Alloy Permanent Mold CastingsASTM B 209 (1996) Aluminum and Aluminum-Alloy Sheet and PlateASTM B 209M (1995) Aluminum and Aluminum-Alloy Sheet and Plate (Metric)ASTM B 221 (1996) Aluminum and Aluminum-Alloy Ex
22、truded Bars, Rods, Wire, Profiles, and TubesASTM B 221M (1996) Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)ASTM C 1036 (1991; R 1997) Flat GlassASTM D 3841 (1997) Glass-Fiber-Reinforced Polyester Plastic PanelsASTM E 84 (1999) Surface Burning Characteristics of
23、 Building MaterialsAMERICAN WELDING SOCIETY (AWS)AWS C1.1 (1966) Recommended Practices for Resistance WeldingAWS D1.1 (2000) Structural Welding Code - SteelAWS D1.2 (1997) Structural Welding Code - AluminumNATIONAL ASSOCIATION OF ARCHITECTURAL METAL MANUFACTURERS (NAAMM)NAAMM AMP 505 (1988) Metal Fi
24、nishes Manual for Architectural and Metal Products; Section: Applied CoatingsNATIONAL FIRE PROTECTION ASSOCIATION (NFPA)NFPA 70 (1999) National Electrical CodeSOCIETY OF AUTOMOTIVE ENGINEERS (SAE)SAE AMS 3611 (1994; Rev D) Plastic Sheet, Polycarbonate General Purpose1.2 GENERALSECTION 10430 Page 5Pr
25、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TESTPDFAll exterior signage shall be provided by a single manufacturer. Exterior signage shall be of the design, detail, sizes, types, and message content shown on the drawings, shall conform to the requi
26、rements specified, and shall be provided at the locations indicated. Signs shall be complete with lettering, framing as detailed, and related components for a complete installation.1.3 WIND LOAD REQUIREMENTSExterior signage shall be designed to withstand _ km/h mph windload.1.4 CHARACTER PROPORTIONS
27、 AND HEIGHTSLetters and numbers on indicated signs for handicapped-accessible buildings shall have a width-to-height ratio between 3:5 and 1:1 and a stroke-width-to-height ratio between 1:5 and 1:10. Characters and numbers on indicated signs shall be sized according to the viewing distance from whic
28、h they are to be read. The minimum height is measured using an upper case letter “X“. Lower case characters are permitted.1.5 SUBMITTALS*NOTE: Submittals must be limited to those necessary for adequate quality control. The importance of an item in the project should be one of the primary factors in
29、determining if a submittal for the item should be required.Indicate submittal classification in the blank space following the name of the item requiring the submittal by using “G“ when the submittal requires Government approval. Submittals not classified as “G“ will show on the submittal register as
30、 “Information Only“. For submittals requiring Government approval, a code of up to three characters should be used following the “G“ designation to indicate the approving authority; codes of “RE“ for Resident Engineer approval, “ED“ for Engineering approval, and “AE“ for Architect-Engineer approval
31、are recommended.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. The following shal
32、l be submitted in accordance with Section 01330 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsApproved Detail Drawings; _, _Drawings showing elevations of each type of sign; dimensions, details, and methods of mounting or anchoring; shape and thickness of materials; and details of construction. A schedule
33、 showing the location, each sign type, and message shall be included.SECTION 10430 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TESTPDFSD-03 Product DataModular Exterior Signage System; _, _Manufacturers descriptive data and catalog cuts.Ins
34、tallation; _, _Manufacturers installation instructions and cleaning instructions.Exterior Signs; _, _Exterior signage schedule in electronic media with spread sheet format. Spread sheet shall include sign location, sign type, and message.Wind Load Requirements; _, _Design analysis and supporting cal
35、culations performed in support of specified signage.SD-04 SamplesExterior Signs; _, _One 300 mm 12 inch length of framing for illuminated signs. One sample of each type of sign _. Each sample shall consist of a complete sign panel with letters and symbols. Samples may be installed in the work, provi
36、ded each sample is identified and location recorded. Two samples of manufacturers standard color chips for each material requiring color selection and 305 mm 12 inch square sample of sign face color sample.SD-10 Operation and Maintenance DataProtection and Cleaning; _, _Six _ copies of maintenance i
37、nstructions listing routine maintenance procedures, possible breakdowns and repairs, and troubleshooting guides. The instructions shall include simplified diagrams for the equipment as installed.1.6 QUALIFICATIONSSigns, plaques, and dimensional letters shall be the standard product of a manufacturer
38、 regularly engaged in the manufacture of the products. Items of equipment shall essentially duplicate equipment that has been in satisfactory use at least 2 years prior to bid opening.1.7 DELIVERY AND STORAGEMaterials shall be wrapped for shipment and storage, delivered to the jobsite in manufacture
39、rs original packaging, and stored in a clean, dry area in accordance with manufacturers instructions.1.8 WARRANTYManufacturers standard performance guarantees or warranties that extend SECTION 10430 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
40、-,-TESTPDFbeyond a one year period shall be provided.1.9 EXTRA STOCK*NOTE: A sufficient number of message panels/bars and letters for future use for changes and message replacement shall be specified.*The Contractor shall provide _ extra interchangeable message panels and extra stock of the followin
41、g: _ message bars of each color and size for sign types _. _ pressure-sensitive letters in each color and size for sign type _. _ changeable message strips for sign type _.PART 2 PRODUCTS2.1 MODULAR EXTERIOR SIGNAGE SYSTEM*NOTE: Omit signage systems not required for project.Enamel finish is more eco
42、nomical than anodized, but may not perform as well; therefore, may not be cost effective. Designer should investigate local conditions to make determination.*Exterior signage shall consist of a system of coordinated directional, identification, and regulatory type signs located where shown. Dimensio
43、ns, details, materials, message content, and design of signage shall be as shown.2.1.1 Free-Standing Base Mount Pylon/Monolith Type Signs*NOTE: Drawings should show mounting heights and mounting details.*2.1.1.1 FramingInterior framing shall consist of aluminum or galvanized steel tube columns welded to companion plates. Perimeter framing shall consist of aluminum or steel angle framing welded to the post and plate system as designed. Framing members shall be designed to permit access to electrical equipment and panel removal. Mounting shall be provided as shown. Framin
