CNS 14386-1-1999 Glossary of terms relating to electric motorcycles《电动机器脚踏车－词汇》.pdf

相关资源

CNS 3105-2001 Method of test for fuel consumption for motorcycles《机器脚踏车燃料消耗量试验法》.pdf

CNS 3106-1988 Method of Brake Test for Motorcycles《机器脚踏车煞车试验法》.pdf

CNS 3107-1988 Method of Acceleration Test for Motor Cycles《机器脚踏车加速试验法》.pdf

CNS 3108-1988 Method of Coasting Test for Motor Cycles《机器脚踏车滑行试验法》.pdf

CNS 14386-10-2000 Limits and methods of measurement for electromagnetic interference of electric motorcycles《电动机器脚踏车电磁干扰限制值与量测方法》.pdf

CNS 14386-11-2000 Life cycle test procedure for batteries of electric motorcycles《电动机器脚踏车-电池寿命试验法》.pdf

CNS 14386-12-2000 Capacity test procedure for batteries of electric motorcycles《电动机器脚踏车-电池容量试验法》.pdf

CNS 14386-13-2000 Energy and power density test procedure for batteries of electric motorcycles《电动机器脚踏车-电池能量及功率密度试验法》.pdf

CNS 14386-3-2000 Method of maximum speed test for electric motorcycles《电动机器脚踏车-最高速率试验法》.pdf

CNS 14386-4-2000 Method of acceleration test for electric motorcycles《电动机器脚踏车-加速性能试验法》.pdf

猜你喜欢

CSN 25 4045-1973 GO and NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《穿过和非穿过型螺纹规 直径为3 mm到100 mm的公制螺纹》.pdf

CSN 25 4046-1973 Setting plug for GO and NOT GO screw calliper gauge Metric thread diameter over 3 mm up to 100 mm《穿过型及非穿过型螺丝两脚规底座插栓 直径3mm到100 mm的公制螺纹》.pdf

CSN 25 4047-1973 NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《非穿过型螺纹规 直径3 mm到00 mm的公制螺纹》.pdf

CSN 25 4048-1985 Setting plug for NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《非穿过型螺丝两脚规定位插塞 直径为3mm到100 mm的公制螺纹》.pdf

CSN 25 4050-1986 Screw gauges Limit screw plug gauges Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 止动螺钉插塞规 直径为G 1 8 到G3 1 2的圆柱形导管螺纹》.pdf

CSN 25 4055-1986 Screw gauges Solid GO screw ring gauges Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 穿过型实心环首螺钉规直径为1 8 - G 3 1 2的圆柱形导管螺纹》.pdf

CSN 25 4056-1986 Screw gauges Minimum and maximum check plugs for solid GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 实心穿过型环首螺钉规最小及最大检测插栓 直径为1 8 - G 3 1 .pdf

CSN 25 4059-1986 Screw gauges Wear check plug for solid and adjustable GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 实心可调通过式环螺钉规耐磨检查插塞 直径为G 1 8 3 1 2的圆柱.pdf

CSN 25 4065-1986 Screw gauges Solid NOT GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 实心非穿过型环首螺钉规 直径为1 8 - G 3 1 2的圆柱形导管螺纹》.pdf