CNS 5435-1987 Dimensions of Starter Pinions and Ring Gears for Automobiles《汽车用起动电动机小齿轮及环形齿轮之尺度》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

ASME STP-PT-049-2012 INVESTIGATION OF TEMPERATURE DERATING FACTORS FOR HIGH-STRENGTH LINE PIPE《高强线管温度降额因子的调查》.pdf

ASME STP-PT-050-2012 AN INVESTIGATION OF THREE RADIOGRAPHIC ACCESS PORT PLUG GEOMETRIES AND THE SURROUNDING PIPE WALL UNDERGOING CREEP《三个辐照接入端口插头几何尺寸和周围管壁经历蠕变的调查》.pdf

ASME STP-PT-052-2012 ALIGN MECHANICAL AND CIVIL-STRUCTURAL EARTHQUAKE DESIGN AND QUALIFICATION RULES FOR ASME B31 PIPING SYSTEMS AND PIPELINES《ASME B31管道系统和管线标准用排列机制与民用建筑抗震设计和合格细则》.pdf

ASME STP-PT-053-2013 CRITERIA DOCUMENT FOR SHELL-AND-TUBE HEAT EXCHANGERS ACCORDING TO PART UHX OF ASME SECTION VIII DIVISION 1《依据ASME第Ⅷ节第1分册第UHX部分壳管式热交换器的标准文档》.pdf

ASME STP-PT-054-2012 Concentrated Solar Power (CSP) Codes and Standards Gap Analysis《聚光式太阳能发电(CSP)规范和标准差异分析》.pdf

ASME STP-PT-056-2013 EXTEND STRESS-STRAIN CURVE PARAMETERS AND CYCLIC STRESS-STRAIN CURVES TO ALL MATERIALS LISTED FOR SECTION VIII DIVISIONS 1 AND 2 CONSTRUCTION《第VIII部 第1和第2分部 建筑.pdf

ASME STP-PT-056-2013 EXTEND STRESS-STRAIN CURVE PARAMETERS AND CYCLIC STRESS-STRAIN CURVES TO ALL MATERIALS LISTED FOR SECTION VIII DIVISIONS 1 AND 2 CONSTRUCTION《第VIII部 第1和第2分部 建筑_1.pdf

ASME STP-PT-058-2013 TEMPER BEAD QUALIFICATION HARDNESS ACCEPTANCE CRITERIA《回火焊道条件硬度验收标准》.pdf

ASME STP-PT-064-2013 EVALUATION OF FRACTURE PROPERTIES TEST METHODS FOR HYDROGEN SERVICE《氢作业用断裂性能试验方法评价》.pdf