1、DEUTSCHE NORM November 199 I I Hot rolled I and H sections (IPB series) Dimensions, mass and static parameters I 1025-2 ICs 77.140.70 Descriptors: Steel, sections, dimensions. Warmgewalzte I-Trger; I-Trger, IPB-Reihe; Mae, Masse, statische Werte Supersedes March 1993 edition. In keeping with current
2、 practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker. Dimensions in mm Foreword This standard has been prepared by the Normenausschu Eisen und Stahl (Steel and Iron Standards Committee). It should be note
3、d that at the European level ECISSTTC 11 is currently reviewing standardized sizes for sections and bearing piles with parallel flanges. Upon publication of the relevant European Standard, DIN 1025-2 to DIN 1025-5 will be withdrawn. Amendments In comparison with the October 1963 edition, H sections
4、with tapered flanges are no longer included. Previous editions DIN 161 2: 1924-09, 1932-01, 1943-03; 1963-1 O. 1994-03. DIN 1025-2: 1926-04, 1928-1 O, 1929-1 2, 1932-03, 1939-09, 1940-07, 1959-07 1 Scope and field of application This standard specifies dimensions and static parameters for hot rolled
5、 I and H sections (H sections, for short), with paral- lel flanges, preferably made from DIN EN 10 025 steel. This standard does not cover: a) hot rolled I sections (I series, with a smaller ratio of flange width to web height; cf. DIN 1025-1); b) hot rolled I and H sections (IPBI series, with thinn
6、er webs and flanges; cf. DIN 1025-3); c) hot rolled I and H sections (IPBv series, with thicker webs and flanges; cf. DIN 1025-4); d) hot rolled I and H sections (IPE series, with narrower flanges; ci. DIN 1025-5). 2 Normative references This standard incorporates, by dated or undated reference, pro
7、visions from other publications. These normative refer- ences are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, sub- sequent amendments to or revisions of any of these publica- tions apply to this standard only when incorporated in it by
8、 amendment or revision. For undated references, the latest edition of the publication referred to applies. DIN 1025-1 Steel sections; hot rolled I beams; dimensions, mass, limit deviations and static values Hot rolled I and H sections (IPBL series); dimensions, mass and static parameters Hot rolled
9、I and H sections (IPBv series); dimensions, mass and static parameters Hot rolled I and H sections (IPE series); dimensions, mass and static parameters Hot rolled unalloyed structural steel products; technical delivery conditions (includes Amendment AI : 1993) Structural steel I and H sections; tole
10、rances on shape and dimensions Wide-flanged steel beams with parallel flanges; dimen- sions DIN 1025-3 DIN 1025-4 DIN 1025-5 DIN EN 10 025 DIN EN 10 034 EU 53-62 Continued on pages 2 to 3. Beuth Verlag Gmbii, Beriin, has the exclusive right of sale for German Standards (DIN-Normen). 05.96 DIN 1025-2
11、 Engl. Price group 5 Sales No. 0105 Page 2 DIN 1025-2 3 Designation The standard designation shall give, in the following order: a) The name of product (H section); b) the DIN number (DIN 1025); c) the material designation or number; d) the section symbol in accordance with table 1. EXAMPLE: The des
12、ignation of a hot rolled H section complying with this standard, made from steel grade S235JR (material number 1.0037) as specified in DIN EN 10 025, of the IPB series, with a height, h, of 360 mm (IPB 360) shall read: H section DIN 1025 - S235JR - IPB 360 or H section DIN 1025 - 1 .O037 - IPB 360 4
13、 Dimensions and mass 4.1 Hot rolled H sections with parallel flanges shall have the dimensions specified in table 1. 4.2 The nominal length shall be specified at the time of ordering. 4.3 The values of mass specified in table 1 have been cal- culated taking the density as 7,85 kg/dm3. Y I t b 5 Form
14、 and dimensional tolerances The dimensions of sections are subject to the tolerances specified in DIN EN 10 034. 6 Material Sections shall preferably be made from DIN EN 10 025 steel, the particular steel grade being specified at the time of order- ing. DIN 1025-2 Page 3 Table 1: Dimensions, mass an
15、d static parameters for sections of the IPB series Dimensions for Static parametersl) Sec- tion area, in cm2 rl Y-Y Mass, Surface x-x in area, kglm in m2/m I, wx i, cm4 cm3 cm S 20,4 1 0,567 1 86: 1 89,gI 4,16 26,7 0,686 144 5,04 6 - _. 7 8 - 33,7 0,805 1 510 216 5,93 42,6 0,918 2 490 31 1 6,78 51,2
16、 1,04 3830 426 7,66 61,3 1,15 5700 570 8,54 9 10 10 10,5 11 11,5 12 - 12,5 13.5 - 14 14,5 - 15 15,5 - 199 2,22 136700 4970 23,2 212 2,32 171 O00 5700 25,2 225 2,42 210 600 6480 27,l 16 17 241 2,52 256900 7340 29,O 262 2,71 359 100 8 980 32,8 291 2,91 494 100 10980 36,5 314 3,11 644700 12890 40,l 17,
17、5 1 O00 1 O00 300 18,5 i i 16280 1 O90 6,38 7430 86,8 19 *) EURONORM 53-62 uses different symbols to designate sections, but they are equivalent to those specified here (.e. an HE 300 B 1) I = second moment of area, W = section modulus, i = radius of gyration (subscripts x and y denoting the relevan
18、t axis). 2) S, = moment of first order of half the cross section. 3) s, = I, : S, = distance between centre of pressure and centre of tension. The values specified for section area, mass, surface area and static parameters have been specified as a function of the other dimensions. section complying with EU 53-62 is the same as an IPB 300 section complying with this standard).
