1、October 2016 English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 61.040; 61.060!%3“2579916www.din.
2、deDIN EN ISO 10734Footwear Test method for slide fasteners Strength of slide fastener pullers (ISO 10734:2016);English version EN ISO 10734:2016,English translation of DIN EN ISO 10734:2016-10Schuhe Prfverfahren fr Reiverschlsse Festigkeit der ReiverschlussSchiebergriffe (ISO 10734:2016);Englische F
3、assung EN ISO 10734:2016,Englische bersetzung von DIN EN ISO 10734:2016-10Chaussures Mthodes dessai des fermetures glissire Rsistance des tirettes des fermetures glissire (ISO 10734:2016);Version anglaise EN ISO 10734:2016,Traduction anglaise de DIN EN ISO 10734:2016-10www.beuth.deDocument comprises
4、 12 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.10.16 DIN EN ISO 10734:2016-10 2 A comma is used as the decimal marker. National foreword This document (EN ISO 10734:2016) has been prepared by Technical Committee CEN/TC 309
5、 “Footwear” (Secretariat: AENOR, Spain) in collaboration with Technical Committee ISO/TC 216 “Footwear”. The responsible German body involved in its preparation was DIN-Normenausschuss Materialprfung (DIN Standards Committee Materials Testing ), Working Committee NA 062-10-11 AA Schuhe. The DIN Stan
6、dards corresponding to the International Standards referred to in this document are as follows: ISO 7500-1 DIN EN ISO 7500-1 ISO 18454 DIN EN 12222 ISO 19952 DIN EN ISO 19952 National Annex NA (informative) Bibliography DIN EN 12222, Footwear Standard atmospheres for conditioning and testing of foot
7、wear and components for footwear DIN EN ISO 7500-1, Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system DIN EN ISO 19952, Footwear Vocabulary EUROPEAN STANDARD NORM
8、E EUROPENNE EUROPISCHE NORM EN ISO 10734 May 2016 ICS 61.060 English Version Footwear - Test method for slide fasteners - Strength of slide fastener pullers (ISO 10734:2016) Chaussures - Mthodes dessai des fermetures glissire - Rsistance des tirettes des fermetures glissire (ISO 10734:2016) Schuhe -
9、 Prfverfahren fr Reiverschlsse - Festigkeit der Reiverschluss-Schiebergriffe (ISO 10734:2016) This European Standard was approved by CEN on 15 April 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st
10、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,
11、German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cro
12、atia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
13、United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No.
14、 EN ISO 10734:2016 EForeword . 41 Scope . 52 Normative references 53 Terms and definitions . 54 Principle 75 Apparatus and materials 75.1 Method 1 Tension 75.2 Method 2 Torsion .75.3 Minimum number of fasteners required 76 Procedure.86.1 Conditioning 86.2 Method 1 Tension 86.3 Method 2 Torsion .97 T
15、est report 10Contents PageEN ISO 10734:2016 (E) DIN EN ISO 10734:2016-10 2European foreword .3European foreword This document (EN ISO 10734:2016) has been prepared by Technical Committee CEN/TC 309 “Footwear“, the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/T
16、C 216 “Footwear“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2016, and conflicting national standards shall be withdrawn at the latest by November 2016. Attention is drawn to the pos
17、sibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries
18、are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
19、Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 10734:2016 has been approved by CEN as EN ISO 10734:2016 without any modification. EN ISO 10734:2016 (E) DIN EN ISO 10734:2016-10 3 ForewordISO (the International Orga
20、nization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establis
21、hed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization
22、.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with th
23、e editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any paten
24、t rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an
25、 explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationISO 10734 was prepared by the Euro
26、pean Committee Standardization (CEN) Technical Committee CEN/TC 309, Footwear, in collaboration with ISO Technical Committee TC 216, Footwear, in accordance with the agreement on technical cooperation between ISO and CEN (Vienna Agreement).EN ISO 10734:2016 (E) DIN EN ISO 10734:2016-10 4 1 ScopeThis
27、 International Standard specifies a test method intended to assess the strength of slide fastener pullers for footwear. The method is applicable to all types of footwear slide fastener.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and
28、 are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 7500-1, Metallic materials Calibration and verification of static uniaxial testing machines Part
29、1: Tension/compression testing machines Calibration and verification of the force-measuring systemISO 18454, Footwear Standard atmospheres for conditioning and testing of footwear and components for footwearISO 19952, Footwear Vocabulary3 Terms and definitionsFor the purposes of this document, the t
30、erms and definitions given in ISO 19952 and the following apply.3.1slide fastenermeans of securing two flexible materials consisting of interlockable teeth each attached to one of the opposing edges of two tapes (3.2) and movable slider that spans the interlocking teeth which when moved in one direc
31、tion causes the teeth (3.5) of one tape to interlock with the teeth of the other tapeNote 1 to entry: When the slider (3.3) is moved in the opposite direction, it causes the teeth to disengage (see Figure 1).EN ISO 10734:2016 (E) DIN EN ISO 10734:2016-10 5 12345Key1 top stop 4 puller2 teeth 5 tape3
32、slider 6 bottom stopFigure 1 Slide fastener3.2tapefabric panels to support other teeth (3.5) of the slide fastener (3.1)3.3slidermeans of drawing the two interlocking teeth together or apart as it traverses the length of the teeth (3.5)3.4pullerpiece of plastic or metal attached to the slider (3.3)
33、as a means of manual grip for the user to operate3.5teethindividual component of the slide fastener (3.1) or continuous plastic spiral which interlocks with an opposing element3.6end stoptop stopterminal components of the teeth (3.5) to prevent the slider (3.3) from disengaging from the teeth and ta
34、pe (3.2)3.7stringertextile tape with an attached row of teeth (3.5) designed to interact with a row attached to another tape (3.2)EN ISO 10734:2016 (E) DIN EN ISO 10734:2016-10 6 4 PrincipleThe slider and puller of a test fastener are clamped so that the puller is perpendicular to the slider body. T
35、his International Standard describes the following methods:Method 1: Tension The force required to pull the puller from the slider in a direction parallel to the longitudinal centre line of the puller is measured;Method 2: Torsion The torque required to twist the puller from the slider about the lon
36、gitudinal centre line of the puller is measured.5 Apparatus and materials5.1 Method 1 TensionA tensile testing machine with the following characteristics shall be used.5.1.1 A jaw separation rate of (100 10) mm/min.5.1.2 The capability of measuring forces up to 1 kN to an accuracy of 2 % as specifie
37、d by Class 2 in ISO 7500-1.5.1.3 A means of recording either the force at all times during the test or the maximum force.5.1.4 A jig, in one jaw, for holding the test fastener slider. A flat plate of thickness at least 1 mm, which fits between the slider and the puller and has a tapered slot to enga
38、ge the slider body, is suitable. An arm attached to the place is clamped into the jaw see Figure 2 a).5.1.5 A device, fixed in the other jaw, for clamping the puller of the test fastener. A small rigid hook is suitable for pullers with a hole.5.2 Method 2 TorsionA test device see Figure 2 b) with th
39、e following characteristics shall be used.5.2.1 A pair of clamps, one capable of holding the test fastener slider and the other capable of gripping the puller so that it is perpendicular to the slider.5.2.2 A method of rotating the two clamps (5.2.1) relative to one another at a rate of (9 3) degree
40、 per second (/s).5.2.3 The capability of measuring the torque between the two clamps to the nearest 0,5 Nm.5.2.4 Protractor capable of measuring angles of twist to the nearest 1.5.3 Minimum number of fasteners requiredThe minimum number of fasteners required for each version of the test are the foll
41、owing: Method 1 Three; Method 2 Six.EN ISO 10734:2016 (E) DIN EN ISO 10734:2016-10 7 6 Procedure6.1 ConditioningThe samples should be conditioned for at least 24 h according to ISO 18454 before the test is carried out and the test should be carried out in this environment.6.2 Method 1 Tension6.2.1 R
42、emove the slider from the stringers of the test fastener. Clamp the main body of the slider in the jig (5.1.4) so that it is at 90 to the axis of the tensile testing machine (5.1).6.2.2 Attach the puller of the test fastener to the device (5.1.5) so that it is parallel to the axis of the tensile tes
43、ting machine (5.1). Try to grip the puller in such a way that the device (5.1.5) will not cause an unnatural failure of the puller during the test. For example, if using a hook with a two hole puller which looks weak around its top hole, insert the hook through the bottom hole in the puller where it
44、 is fixed to the slider body.6.2.3 Operate the tensile testing machine with a jaw separation rate of (100 10) mm/min until either the puller breaks or pulls off the slider.6.2.4 Record the maximum force obtained in newtons to the nearest 5 N and the type of failure such as the following: slider brok
45、e at the point of attachment to the puller; puller broke at the point of attachment to the slider; slider broke at a point away from the attachment to the puller; puller broke at a point away from the attachment to the slider.EN ISO 10734:2016 (E) DIN EN ISO 10734:2016-10 8 12345672a) Tension b) Tor
46、sionKey1 hook (5.1.5) 5 axis of tensile tester2 puller 6 axis of rotation3 slider 7 clamp (5.2.1)4 plate (5.1.4)Figure 2 Test device6.2.5 If the puller failed at the point of contact with the device (5.1.5), or it appears that the device contributed to the failure, then ignore this result and repeat
47、 the test with a fresh fastener.6.2.6 Repeat the procedure in 6.2.1 to 6.2.5 with the other two test fasteners.6.2.7 Calculate the arithmetic mean of the three maximum forces (6.2.4).6.3 Method 2 Torsion6.3.1 Remove the slider from the stringers of the test fastener. Clamp the slider in one of the clamps (5.2.1) and the puller in the other, so that the puller is perpendicular to the slider and the longitudinal centre line of the puller is aligned with the axis of rotation between the two clamps see Figure 2 b).6.3.2 O
