1、February 2015 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I
2、CS 83.080.20!%B*“2293107www.din.deDDIN EN ISO 19066-1Plastics Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) mouldingand extrusion materials Part 1: Designation system and basis for specifications(ISO 19066-1:2014);English version EN ISO 19066-1:2014,English translation of DIN EN ISO 190
3、66-1:2015-02Kunststoffe Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 19066-1:2014);Englische Fassung EN ISO 19066-1:2014,Englische bersetzung von DIN EN ISO 19066-1:2015-02Plastiques Matriaux plastique (mthacrylate de mt
4、hyle)-acrylonitrile-butadine-styrne (MABS)pour moulage et extrusion Partie 1: Systme de dsignation et base de spcifications (ISO 19066-1:2014);Version anglaise EN ISO 19066-1:2014,Traduction anglaise de DIN EN ISO 19066-1:2015-02SupersedesDIN EN ISO 10366-1:2003-02www.beuth.deDocument comprises 15 p
5、agesIn case of doubt, the German-language original shall be considered authoritative.01.15 DIN EN ISO 19066-1:2015-02 2 A comma is used as the decimal marker. National foreword This document (EN ISO 19066-1:2014) has been prepared by Technical Committee ISO/TC 61 “Plastics” (Secretariat: SAC, China)
6、 in collaboration with Technical Committee ISO/TC 249 “Plastics” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-02-10 AA Thermoplast-Formmassen. The revised desi
7、gnation system is published under a new ISO number, as many existing documents refer to ISO 10366-1. If the existing ISO 10366-1 would be replaced by the new designation system, these documents would refer to the incorrect designation system. In order to give users time to switch from EN ISO 10366-1
8、 to EN ISO 19066-1, EN ISO 10366-1 needs to be phased out in 5 to 10 years. During this period, ISO 10366-2 will effectively be Part 2 of this International Standard. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1043-1 DIN EN ISO 104
9、3-1 ISO 1043-2 DIN EN ISO 1043-2 ISO 10366-2 DIN EN ISO 10366-2 Amendments This standard differs from DIN EN ISO 10366-1:2003-02 as follows: a) the number of the standard has been changed to DIN EN ISO 19066-1; b) the data block system has been simplified and connected more to ISO 1043 and ISO 11469
10、, where the first two blocks are used for generic identification and marking of products. c) normative references have been updated; d) the standard has been editorially revised. Previous editions DIN EN ISO 10366-1: 1999-10, 2003-02 DIN EN ISO 19066-1:2015-02 3 National Annex NA (informative) Bibli
11、ography DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics DIN EN ISO 1043-2, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials DIN EN ISO 10366-2, Plastics Methyl methacrylate-acrylonitrile-butadiene-styr
12、ene (MABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties DIN EN ISO 19066-1:2015-02 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 19066-1 October 2014 ICS 83.080.20 Supersedes EN ISO 10366-1:2002En
13、glish Version Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19066-1:2014) Plastiques - Matriaux plastique (mthacrylate de mthyle)-acrylonitrile-butadine-styrne (MABS) pour moulage
14、et extrusion - Partie 1: Systme de dsignation et base de spcifications (ISO 19066-1:2014) Kunststoffe - Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 19066-1:2014) This European Standard was approved by CEN on 6 Septemb
15、er 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obta
16、ined on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CE
17、N-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland
18、, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre
19、: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 19066-1:2014 EContents PageForeword 3Introduction .41 Scope . 52 Normative references 53 Designation system 63.1 General . 63.2 Data block
20、 1 . 63.3 Data block 2 . 73.4 Data block 3 . 73.5 Data block 4 . 83.6 Data block 5 104 Example of a designation 10DIN EN ISO 19066-1:2015-02 EN ISO 19066-1:2014 (E) 2 Foreword This document (EN ISO 19066-1:2014) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Tech
21、nical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2015, and conflicting national standards shall be withdrawn at
22、the latest by April 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10366-1:2002. According to t
23、he CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
24、Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 19066-1:2014 has been approved by CEN as EN ISO 19066-1:2014 witho
25、ut any modification. DIN EN ISO 19066-1:2015-02 EN ISO 19066-1:2014 (E) 3 IntroductionISO 10366-1:2002 is complex and does not fit with daily practice anymore. In practice ISO 1043 and ISO 11469 are, in combination, improperly being used as a designation system for, e.g. marking. The aim of this Int
26、ernational Standard is to simplify the data block system and to connect more to ISO 1043 and ISO 11469, where the first two blocks are used for generic identification and marking of products.DIN EN ISO 19066-1:2015-02 EN ISO 19066-1:2014 (E) 4 1 ScopeThis part of ISO 19066 establishes a system of de
27、signation for methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials, which can be used as the basis for specifications.The types of MABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properti
28、esa) Vicat softening temperature,b) melt volume-flow rate,c) Charpy notched impact strength, andd) tensile modulus,and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.This part of ISO 1
29、9066 is applicable to all methyl methacrylate-acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or an alkyl-substituted styrene), acrylonitrile and methyl methacrylate, and a dispersed elastomeric phase based on butadiene.It applies
30、 to MABS materials ready for normal use in the form of powder, granules, or pellets, unmodified or modified by colorants, additives, fillers, etc.It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19066 does not provide engi
31、neering data, performance data, or data on processing conditions which might be required to specify a material for a particular application and/or method of processing.If such additional properties are required, they will be determined in accordance with the test methods specified in ISO 10366-2, if
32、 suitable.In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements can be given in data block 5 (see 3.1).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and
33、 are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special character
34、isticsISO 1043-2, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materialsDIN EN ISO 19066-1:2015-02 EN ISO 19066-1:2014 (E) 5 ISO 10366-2:2003, Plastics Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Part 2: Preparation of test sp
35、ecimens and determination of properties3 Designation system3.1 GeneralThe designation system for thermoplastics is based on the following standard pattern:DesignationDescription block (optional)Identity blockInternational Standard number blockIndividual-item blockData block 1Data block 2Data block 3
36、Data block 4Data block 5The designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks com
37、prising the following information.Data block 1: Identification of the plastic by its abbreviated term MABS in accordance with ISO 1043-1 and information about the composition of the polymer (see 3.2).Data block 2: Fillers or reinforcing materials and their nominal content (see 3.3).Data block 3: Pos
38、ition 1: Intended application and/or method of processing (see 3.4).Positions 2 to 8: Important properties, additives, and supplementary information (see 3.4).Data block 4: Designatory properties (see 3.5).Data block 5: For the purpose of specifications, a fifth data block can be added containing ad
39、di-tional information (see 3.6).The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by a comma.If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,).3.2 Data block 1In this data
40、block, after the hyphen, the plastic is identified by its abbreviated term (MABS) in accordance with ISO 1043-1, followed by a hyphen and a single code letter giving additional information on the composition as specified in Table 1.Table 1 Code letters used for additional information on the composit
41、ion in data block 1Code letterRange of AN content% by massRange of MMA content% by massA 10 but 50B 50 but 80C 30 10 but 50D 30 50DIN EN ISO 19066-1:2015-02 EN ISO 19066-1:2014 (E) 6 For the purposes of this part of ISO 19066, the AN content of the continuous phase shall be determined in accordance
42、with ISO 10366-2:2003, Annex A.The MMA content of the compound shall be determined by measurement of the oxygen content.3.3 Data block 2In this data block, the type of filler and/or reinforcing material is represented by a one code letter in position 1 and its physical form by a second code letter i
43、n position 2, the code letters being as specified in Table 2 in accordance with ISO 1043-2. Subsequently (without a space), the mass content can be given by a two-figure number. If the mass content of filler and/or reinforcing material is less than 10 %, the first figure number of the figure is pres
44、ented by 0 and the second figure, of the mass content.Mixtures of filler materials or forms can be indicated by combining the relevant codes using the sign “+” within parentheses followed by the total filler content outside the parenthesis. For example, a mixture of 25 % glass fibres (GF) and 10 % m
45、ineral powder (MD) would be indicated by (GF+MD)35 or (GF25+MD10).Table 2 Code letters for fillers and reinforcing materials in data block 2Code letter Material (Position 1) Form (Position 2)B boron beads, spheres, ballsC carbonaD fines, powderF fibreG glass groundH whiskersK calcium carbonateL cell
46、uloseM mineralaME metalbS synthetic organicaflakesT talcumX not specified not specifiedZ othersaothersaThese materials can be identified after the code letter, e.g. by chemical symbol or additional codes to be agreed upon.bThe type of metal shall be identified by means of the relevant chemical symbo
47、l(s) after the mass content. For example, steel whiskers can be designated “MEH05Fe”.3.4 Data block 3In this data block, information about the method of processing is represented by a code letter, followed by code letters about additives, supplementary information, and other characteristics. The code letters used are specified in Table 3.If no specific information is given on the method of processing,
