1、December 2014Translation by DIN-Sprachendienst.English price group 19No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 47.080!%S)“2274806www.din.deDDIN EN ISO 6185-3Inflatable boats Part 3: Boats with a hull length less than 8 m with a motor power ratingof 15 kW and greater (ISO 6185-3:2014);English version EN ISO 6185-3:2014,English translation of DIN EN ISO 6185-3:2014-12Aufblasbare Boote Teil 3: Boote mit einer
3、 Rumpflnge unter 8 m mit einer Motorleistung von mindestens15 kW (ISO 6185-3:2014);Englische Fassung EN ISO 6185-3:2014,Englische bersetzung von DIN EN ISO 6185-3:2014-12Bateaux pneumatiques Partie 3: Bateaux dune longueur de coque infrieure 8 m et dune puissance moteurassigne suprieure ou gale 15 k
4、W (ISO 6185-3:2014);Version anglaise EN ISO 6185-3:2014,Traduction anglaise de DIN EN ISO 6185-3:2014-12SupersedesDIN EN ISO 6185-3:2002-06See start of applicationwww.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.4412.14 DIN EN ISO 6
5、185-3:2014-12 2 A comma is used as the decimal marker. Start of application The start of application of this standard is 2014-12-01. DIN EN ISO 6135-3:2002-06 may be used in parallel until 2016-08-31. National foreword This standard includes safety requirements within the meaning of the Produktsiche
6、rheitsgesetz (ProdSG) (German Product Safety Act). This document (EN ISO 6185-3:2014) has been prepared by Technical Committee ISO/TC 188 “Small Craft” (Secretariat: SIS, Sweden) in collaboration with Technical Committee CEN/SS T01 “Shipbuilding and maritime structures” (Secretariat: CCMC). The resp
7、onsible German body involved in its preparation was the DIN-Normenausschuss Sport- und Freizeitgert (DIN Standards Committee Sports Equipment), Working Committee NA 112-05-09 AA Aufblas-bare schwimmende Freizeitgerte einschlielich aufblasbarer Boote und Zubehr. Where this standard has been identifie
8、d by the Ausschuss fr Produktsicherheit (German Committee for Product Safety) and reference to it has been published in the Gemeinsames Ministerialblatt (German Joint Ministerial Gazette) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safet
9、y and Health), it is to be presumed that inflatable boats which comply with this standard fulfil the relevant health and safety requirements. EN ISO 6185 consists of the following parts, under the general title Inflatable boats: Part 1: Boats with a maximum motor power rating of 4,5 kW Part 2: Boats
10、 with a maximum motor power rating of 4,5 kW to 15 kW inclusive Part 3: Boats with a hull length less than 8 m and with a motor power rating of 15 kW and greater Part 4: Boats with a hull length of between 8 m and 24 m and with a maximum motor power rating of 15 kW and greater The DIN Standards corr
11、esponding to the International Standards referred to in this document are as follows: ISO 1817 DIN ISO 1817 ISO 10592 DIN EN ISO 10592 ISO 2411 DIN EN ISO 2411 ISO 11105 DIN EN ISO 11105 ISO 3864-1 DIN ISO 3864-1 ISO 11547 DIN EN ISO 11547 ISO 4674-1 DIN EN ISO 4674-1 ISO 11592 DIN EN ISO 11592 ISO
12、6185-4 DIN EN ISO 6185-4 ISO 11812 DIN EN ISO 11812 ISO 7010 DIN EN ISO 7010 ISO 12215-3 DIN EN ISO 12215-3ISO 8099 DIN EN ISO 8099 ISO 12215-5 DIN EN ISO 12215-5ISO 8666 DIN EN ISO 8666 ISO 12216 DIN EN ISO 12216 ISO 8847 DIN EN ISO 8847 ISO 12217-1 DIN EN ISO 12217-1ISO 8848 DIN EN 28848 ISO 12217
13、-3 DIN EN ISO 12217-3ISO 9093-2 DIN EN ISO 9093-2 ISO 13297 DIN EN ISO 13297 ISO 9094 DIN EN ISO 9094 ISO 14945 DIN EN ISO 14945 ISO 9775 DIN EN 29775 ISO 14946 DIN EN ISO 14946 ISO 10087 DIN EN ISO 10087 ISO 15084 DIN EN ISO 15084 ISO 10088 DIN EN ISO 10088 ISO 15085 DIN EN ISO 15085 ISO 10133 DIN
14、EN ISO 10133 ISO 15652 DIN EN ISO 15652 ISO 10239 DIN EN ISO 10239 ISO 16180 DIN EN ISO 16180 ISO 10240 DIN EN ISO 10240 ISO 21487 DIN EN ISO 21487 DIN EN ISO 6185-3:2014-12 3 Amendments This standard differs from DIN EN ISO 6185-3:2002-06 as follows: a) the Foreword has been updated; b) Clause 2 “N
15、ormative references” has been updated; c) Clause 3 “Terms and definitions” has been extended and updated; d) Clause 4 “Symbols” has been added; e) new requirements and test methods have been included: 1) Clause 5 “Structural materials” (new Subclause 5.7 “Buoyant material used in foam filled buoyanc
16、y tubes”); 2) Clause 6 “Functional components”, new subclauses: i) 6.11 “Electrical installations (where offered as standard or optional equipment)”; ii) 6.12 “Engine and engine spaces”; iii) 6.13 Fuel systems”; iv) 6.14 “Ventilation of petrol engine and/or petrol tank compartments (where applicable
17、)”; v) 6.15 “Devices for lifting the boat (if applicable)”; vi) 6.16 “Fire protection (if applicable)”; vii) 6.17 “Openings in hull, deck or superstructure”; viii) 6.18 “Gas systems”; ix) 6.19 “Navigational lights”; x) 6.20 “Discharge prevention”; 3) Clause 7 “Safety requirements of the completed bo
18、at” has been revised in form and substance and Subclause 7.3 “Static stability” has been added; 4) Clause 8 “Performance” has been revised in form and substance; 5) Clause 9 “Builders plate(s)” has been revised in form and substance; 6) Clause 10 “Owners manual” has been revised in form and substanc
19、e; f) the Bibliography has been extended and updated. Previous editions DIN EN ISO 6185-3: 2002-06 DIN EN ISO 6185-3:2014-12 4 National Annex NA (informative) Bibliography DIN EN 28848, Small craft Remote steering systems DIN EN 29775, Small craft Remote steering systems for single outboard motors o
20、f 15 kW to 40 kW DIN EN ISO 2411, Rubber- or plastics-coated fabrics Determination of coating adhesion DIN EN ISO 4674-1, Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods DIN EN ISO 6185-4, Inflatable boats Part 4: Boats with a hull length of
21、between 8 m and 24 m and with a maximum motor power rating of 15 kW and greater DIN EN ISO 7010, Graphical symbols Safety colours and safety signs Registered safety signs DIN EN ISO 8099, Small craft Toilet waste retention systems DIN EN ISO 8666, Small craft Principal data DIN EN ISO 8847, Small cr
22、aft Steering gear Cable and pulley systems DIN EN ISO 9093 (all parts), Small craft Seacocks and through-hull fittings DIN EN ISO 9094, Small craft Fire protection DIN EN ISO 10087, Small craft Craft identification Coding system DIN EN ISO 10088, Small craft Permanently installed fuel systems DIN EN
23、 ISO 10133, Small craft Electrical systems Extra-low-voltage d.c. installations DIN EN ISO 10239, Small craft Liquefied petroleum gas (LPG) systems DIN EN ISO 10240, Small craft Owners manual DIN EN ISO 10592, Small craft Hydraulic steering systems DIN EN ISO 11105, Small craft Ventilation of petrol
24、 engine and/or petrol tank compartments DIN EN ISO 11547, Small craft Start-in-gear protection DIN EN ISO 11592, Small craft less than 8 m length of hull Determination of maximum propulsion power rating DIN EN ISO 11812, Small craft Watertight cockpits and quick-draining cockpits DIN EN ISO 12215-3,
25、 Small craft Hull construction and scantlings Part 3: Materials: Steel, aluminium alloys, wood, other materials DIN EN ISO 12215-5, Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination DIN EN ISO 6185-3:2014-12 5 DIN EN ISO 12
26、216, Small craft Windows, portlights, hatches, deadlights and doors Strength and watertightness requirements DIN EN ISO 12217-1, Small craft Stability and buoyancy assessment and categorization Part 1: Non-sailing boats of hull length greater than or equal to 6 m DIN EN ISO 12217-3, Small craft Stab
27、ility and buoyancy assessment and categorization Part 3: Boats of hull length less than 6 m DIN EN ISO 13297, Small craft Electrical systems Alternating current installations DIN EN ISO 14945, Small craft Builders plate DIN EN ISO 14946, Small craft Maximum load capacity DIN EN ISO 15084, Small craf
28、t Anchoring, mooring and towing Strong points DIN EN ISO 15085, Small craft Man-overboard prevention and recovery DIN EN ISO 15652, Small craft Remote steering systems for inboard mini jet boats DIN EN ISO 16180, Small craft Navigation lights Installation, placement and visibility DIN EN ISO 21487,
29、Small craft Permanently installed petrol and diesel fuel tanks DIN ISO 1817, Rubber, vulcanized Determination of the effect of liquids DIN ISO 3864-1, Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings DIN EN ISO 6185-3:2014-12 6 This pag
30、e is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6185-3 August 2014 ICS 47.080 Supersedes EN ISO 6185-3:2001English Version Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater (ISO 6185-3:2014) Bateaux pneumatiqu
31、es - Partie 3: Bateaux dune longueur de coque infrieure 8 m et dune puissance moteur assigne suprieure ou gale 15 kW (ISO 6185-3:2014)Aufblasbare Boote - Teil 3: Boote mit einer Rumpflnge unter 8 m mit einer Motorleistung von mindestens 15 kW (ISO 6185-3:2014) This European Standard was approved by
32、CEN on 21 June 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards
33、 may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifi
34、ed to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icel
35、and, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Manag
36、ement Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6185-3:2014 EContents Page Foreword 4 Introduction 5 1 Scope 7 2 Normative references 7 3 Terms and definitions . 9 4 Symbols
37、10 5 Structural Materials 11 5.1 General 11 5.2 Materials making up the flexible floor and buoyancy tube . 11 5.3 Wood 13 5.4 Metal parts 13 5.5 Glass-reinforced plastics . 13 5.6 Other materials . 13 5.7 Buoyant material used in foam filled buoyancy tubes 13 6 Functional components . 15 6.1 Conditi
38、oning . 15 6.2 Fittings bonded to the flexible parts of the boat . 15 6.3 Manual lifting and carrying devices 15 6.4 Valves (if applicable) . 15 6.5 Rowlocks and oars . 16 6.6 Transom (where applicable) . 17 6.7 Hull drainage 17 6.8 Remote steering system (where offered as standard or optional equip
39、ment) 17 6.9 Towing, anchoring and mooring devices 17 6.10 Seating and attachment systems (where offered as a standard or optional equipment) 17 6.11 Electrical installations (where offered as standard or optional equipment) 18 6.12 Engine and engine spaces . 18 6.13 Fuel systems . 18 6.14 Ventilati
40、on of petrol engine and/or petrol tank compartments (where applicable) . 18 6.15 Devices for lifting the boat (if applicable) 18 6.16 Fire protection (if applicable) . 19 6.17 Openings in hull, deck or superstructure . 19 6.18 Gas systems . 19 6.19 Navigational lights . 19 6.20 Discharge prevention
41、19 7 Safety requirements of the completed boat . 19 7.1 Maximum Load Capacity . 19 7.2 Crew limit (CL) 19 7.3 Static stability 19 7.4 Buoyancy requirements 21 7.5 Compartmentation . 23 7.6 Nominal pressures (inflatable buoyancy tubes) . 23 7.7 Strength of the inflatable buoyancy tube . 23 7.8 Maximu
42、m motor power . 24 7.9 Man overboard prevention and recovery 24 7.10 Field of vision from the helm position . 25 DIN EN ISO 6185-3:2014-12 EN ISO 6185-3:2014 (E) 2 7.11 Provision for (a) liferaft(s) . 25 7.12 Strength of the Rigid Structure (type test only) 25 7.13 Strength of principal fitted acces
43、sories . 25 7.14 Safety Sign . 27 8 Performance . 27 8.1 General 27 8.2 Drop test (Ribs only) . 27 8.3 In-water performance 28 8.4 Rowing test (where applicable, see 6.5) . 29 8.5 Watertightness test (not applicable to open floor, self-bailing boats) . 29 8.6 Manoeuvring-speed test 29 8.7 Self-Drain
44、ing (type VIII Boats only) 31 9 Builders plate(s) 31 10 Owners manual 31 11 Standard equipment DIN EN ISO 6185-3:2014-12 EN ISO 6185-3:2014 (E) 3 32Annex A (informative) General arrangement of a typical Type VII boat . 33 Annex B (informative) General arrangement of a typical Type VIlI boat 34 Requi
45、rements of EU Directive 94/25/EC as amended by Directive 2003/44/EC . 36 Bibliography . 38 Annex ZA (informative) Relationship between this European Standard and the Essential Foreword This document (EN ISO 6185-3:2014) has been prepared by Technical Committee ISO/TC 188 “Small craft”. This European
46、 Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2015, and conflicting national standards shall be withdrawn at the latest by August 2016. Attention is drawn to the possibility that some of the element
47、s of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 6185-3:2001. This document has been prepared under a mandate given to CEN by the European Commission and the Europea
48、n Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following coun
49、tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Sl