1、October 2010 Translation by DIN-Sprachendienst.English price group 21No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 23.020.30!$kTv“1724983www.din.deDDIN EN ISO 9809-2Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steelcylinders with tensile strength greater than or equal to 1100 MPa(ISO 9809-2:2010)English translation of DIN EN ISO 9809-2:201
3、0-10Gasflaschen Wiederbefllbare nahtlose Gasflaschen aus Stahl Gestaltung, Konstruktion und Prfung Teil 2: Flaschen aus vergtetem Stahl mit einerZugfestigkeit grer als oder gleich 1100 MPa (ISO 9809-2:2010)Englische bersetzung von DIN EN ISO 9809-2:2010-10Bouteilles gaz Bouteilles gaz rechargeables
4、en acier sans soudure Conception, construction et essais Partie 2: Bouteilles en acier tremp et revenu ayantune rsistance la traction suprieure ou gale 1100 MPa (ISO 9809-2:2010)Traduction anglaise de DIN EN ISO 9809-2:2010-10SupersedesDIN EN 1964-2:2002-02www.beuth.deIn case of doubt, the German-la
5、nguage original shall be considered authoritative.Document comprises 56 pages10.10 DIN EN ISO 9809-2:2010-10 2 A comma is used as the decimal marker. National foreword This document has been prepared by Technical Committee ISO/TC 58 “Gas cylinders” in collaboration with Technical Committee CEN/TC 23
6、 “Transportable gas cylinders” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Druckgasanlagen (Pressurized Gas Installations Standards Committee), Working Committee NA 016-00-03 AA Druckgas-flaschen und Ausrstung. This Internationa
7、l Standard has been developed to address the general requirements laid down in 6.2.1 of the United Nations “Recommendations on the Transport of Dangerous Goods Model Regulations”, ST/SG/AC.10/1/Rev.16. It is intended for use under a number of regulatory regimes, but is suitable for use with the conf
8、ormity assessment system described in 6.2.2.5 of the above-mentioned Model Regulations. This standard, which has been adopted as a European Standard, is also intended to be used under the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR) and the Regulations co
9、ncerning the International Carriage of Dangerous Goods by Rail (RID). The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 148-1 DIN EN ISO 148-1 ISO 6506-1 DIN EN ISO 6506-1 ISO 6508-1 DIN EN ISO 6508-1 ISO 6892-1 DIN EN ISO 6892-1 ISO 7438
10、 DIN EN ISO 7438 ISO 11114-1 DIN EN ISO 11114-1 ISO 13769 DIN EN ISO 13769 Amendments This standard differs from DIN EN 1964-2:2002-02 as follows: a) the standard has been brought in line with the state of the art; b) the standard has been editorially revised to reflect the current rules for draftin
11、g publications. Furthermore, the difference between ISO 9809-2:2010 and ISO 9809-2:2000 is described in the European Foreword. However, the 2000 edition was not adopted within Germany. Previous editions DIN EN 1964-2: 2002-02 DIN EN ISO 9809-2:2010-10 3 National Annex NA (informative) Bibliography D
12、IN EN ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method DIN EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method DIN EN ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) DIN EN ISO 689
13、2-1, Metallic materials Tensile testing Part 1: Method of test at room temperature DIN EN ISO 7438, Metallic materials Bend test DIN EN ISO 11114-1, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials DIN EN ISO 13769, Gas cylinders
14、Stamp marking DIN EN ISO 9809-2:2010-10 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 9809-2 April 2010 ICS 23.020.30 Supersedes EN 1964-2:2001English Version Gas cylinders - Refillable seamless steel gas cylinders - Design, construction and testing - Pa
15、rt 2: Quenched and tempered steel Bouteilles gaz - Bouteilles gaz rechargeables en acier rsistance la traction suprieure ou gale 1 100 MPa (ISO 9809-2:2010) Gasflaschen - Wiederbefllbare nahtlose Gasflaschen aus Stahl - Gestaltung, Konstruktion und Prfung - Teil 2: Flaschen aus vergtetem Stahl mit e
16、iner Zugfestigkeit grer als oder gleich 1 100 MPa (ISO 9809-2:2010) This European Standard was approved by CEN on 18 March 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar
17、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other la
18、nguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Est
19、onia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUR
20、OPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9809-2:2010: EPartie 2: Bouteilles en acier tremp et revenu ayant une sans soudure - Concepti
21、on, construction et essais - 1 100 MPa (ISO 9809-2:2010) cylinders with tensile strength greater than or equal to 2 Contents Page Foreword3 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Symbols 8 5 Inspection and testing.9 6 Materials .9 7 Design 12 8 Construction a
22、nd workmanship 16 9 Type approval procedure. 18 10 Batch tests. 24 11 Tests/examinations on every cylinder 32 12 Certification. 33 13 Marking 34 Annex A (informative) Description and evaluation of manufacturing imperfections and conditions for rejection of seamless steel gas cylinders at time of fin
23、al visual inspection by the manufacturer. 35 Annex B (normative) Ultrasonic examination . 41 Annex C (informative) Type approval certificate. 47 Annex D (informative) Acceptance certificate. 48 Annex NA (normative) Specific European requirements. 50 Bibliography. 5 DIN EN ISO 9809-2:2010-10 EN ISO 9
24、809-2:2010 (E) 23 Foreword This document (EN ISO 9809-2:2010) has been prepared by Technical Committee ISO/TC 58 “Gas cylinders“ in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders”, the secretariat of which is held by BSI. This European Standard shall be given the statu
25、s of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at the latest by October 2010. Attention is drawn to the possibility that some of the elements of this document may be the subj
26、ect of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1964-2:2001. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports
27、 essential requirements of EU Directive(s). For Specific European requirements, see normative Annex NA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European
28、Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the Un
29、ited Kingdom. This second edition cancels and replaces the first edition (ISO 9809-2:2000), which has been technically revised. a) the reduction of maximum sulfur content in 6.2.2 from 0,010 % to 0,005 %, which is now applicable to all strength levels; b) the note in 7.3 regarding limitation of the
30、F factor was deleted (as required by the United Nations Recommendations on the Transport of Dangerous Goods: Model Regulations); c) the modification of provisions for ultrasonic examination in 8.4 to include ultrasonic examination on the cylindrical area to be closed, prior to the forming process; d
31、) the addition of the requirement of a base check according to 9.2.6 for all cylinder types during prototype testing; e) the addition of the requirement of a base check according to 9.2.6 for cylinders made from continuously cast billet material during batch testing. ISO 9809 consists of the followi
32、ng parts, under the general title Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing: Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal
33、to 1 100 MPa Part 3: Normalized steel cylinders Stainless steel cylinders with tensile strength of less than 1 100 MPa will form the subject of a part 4. DIN EN ISO 9809-2:2010-10 EN ISO 9809-2:2010 (E) 4 Endorsement notice The text of ISO 9809-2:2010 has been approved by CEN as a EN ISO 9809-2:2010
34、 without any modification. DIN EN ISO 9809-2:2010-10 EN ISO 9809-2:2010 (E) Introduction This part of ISO 9809 provides a specification for the design, manufacture, inspection and testing of a seamless steel cylinder for worldwide usage. The objective is to balance design and economic efficiency aga
35、inst international acceptance and universal utility. ISO 9809 (all parts) aims to eliminate existing concern; about climate, duplicate inspections and restrictions because of a lack of definitive International Standards. This part of ISO 9809 should not be construed as reflecting on the suitability
36、of the practice of any nation or region. This part of ISO 9809 addresses the general requirements on design, construction and initial inspection and test of pressure receptacles of the United Nations Recommendations on the Transport of Dangerous Goods: Model Regulations. It is intended to be used un
37、der a variety of regulatory regimes, but is suitable for use with the conformity assessment system in 6.2.2.5 of the above-mentioned Model Regulations. 5DIN EN ISO 9809-2:2010-10 EN ISO 9809-2:2010 (E) 1 Scope This part of ISO 9809 specifies minimum requirements for the material, design, constructio
38、n and workmanship, manufacturing processes, examination and testing at manufacture of refillable quenched and tempered seamless steel gas cylinders of water capacities from 0,5 l up to and including 150 l for compressed, liquefied and dissolved gases. This part of ISO 9809 is applicable to cylinders
39、 with a maximum tensile strength RmaW 1 100 MPa. It is not applicable to cylinders with Rma,max 1 300 MPa for diameters 140 mm and guaranteed wall thicknesses a W 12 mm and Rma,max 1 400 MPa for diameters u 140 mm and guaranteed wall thicknesses a W 6 mm, because beyond these limits, additional requ
40、irements can apply. NOTE 1 If desired, cylinders of water capacity less than 0,5 l and between 150 l and 500 l can be manufactured and certified to be in compliance with this part of ISO 9809. NOTE 2 For quenched and tempered steel cylinders with maximum tensile strength less than 1 100 MPa, see ISO
41、 9809-1. For normalized steel cylinders, see ISO 9809-3. NOTE 3 Grades and strength ranges of steels used for these types of cylinders might not be compatible with some gas service (see 6.1.4) and operational conditions. 2 Normative references The following referenced documents are indispensable for
42、 the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method ISO 6506-1, Metallic materi
43、als Brinell hardness test Part 1: Test method ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature ISO 7438, Metallic materials Bend test ISO 9329-1
44、, Seamless steel tubes for pressure purposes Technical delivery conditions Part 1: Unalloyed steels with specified room temperature properties ISO 9712, Non-destructive testing Qualification and certification of personnel 6DIN EN ISO 9809-2:2010-10 EN ISO 9809-2:2010 (E) ISO 11114-1, Transportable g
45、as cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials ISO 13769, Gas cylinders Stamp marking 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 batch quantity of up to 200 cylinders plus cylinder
46、s for destructive testing of the same nominal diameter, thickness, length and design made successively on the same equipment, from the same cast of steel and subjected to the same heat treatment for the same duration of time 3.2 burst pressure pbhighest pressure reached in a cylinder during a burst
47、test 3.3 design stress factor F ratio of equivalent wall stress at test pressure, ph, to guaranteed minimum yield strength, Reg3.4 quenching hardening heat treatment in which a cylinder, which has been heated to a uniform temperature above the upper critical point, Ac3, of the steel, is cooled rapid
48、ly in a suitable medium 3.5 tempering toughening heat treatment which follows quenching, in which the cylinder is heated to a uniform temperature below the lower critical point, Ac1, of the steel 3.6 test pressure phrequired pressure applied during a pressure test NOTE It is used for cylinder wall t
49、hickness calculation. 3.7 working pressure settled pressure of a compressed gas at a uniform reference temperature of 15 C in a full gas cylinder 3.8 yield strength stress value corresponding to the upper yield strength, ReH, or for steels which do not exhibit a defined yield, the 0,2 % proof strength (non-proportional extension), Rp0, 2 (see ISO 6892-1) 7DIN EN ISO 9809-2:2010-10 EN ISO 9809-2:2010 (E) 4 Symbols a Calculated minimum thickness, in millimetres,
