1、A-A-50047A m 9999974 OL209OL 848 m A-A-50047A December 15, 1992 SUPERSEDING A-A-50047 March 28, 1983 (KIMMEWJIAL ITEM DESCRIPTIN DRY CLEANING UNIT ASSEMBLY, DRY 110 DRY, The General Services Administration has authorized the use of this Comnercial Item Description in preference to MIL-il-43164. 1. (
2、ILASSIFICATION 1.1 Classification. This carniercial item description covers dry to dry, synthetic dry cleaning units in the following sizes, controls, and filtration systems, as specified (see 5.2): Sizes: (dry weight capcity, minimum) 25 pounds 60 pwnds 30 pounds 65 pounds 35 pounds 70 pounds 40 po
3、unds 75 pounds 45 pounds 80 pounds 50 po- 100 pounds 55 pounds Beneficial camients, recamiendations, additions, deletions, clarifications, etc., and any data which my improve this document should be sent to: carniander, U.S. Army Natick Research, Developnent, and Engineering Center, ATIN: SA%-UXT, N
4、atick, MA 01760-5017. AIUISC: N/A FSC 3510 DISTRIERTTIQN STAll3E“ A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50047A 9999974 0320902 784 A-A-50047A Controls : C - Card reader M - Micr
5、oprocessor Filtration svstem: C - Cartridge filter S - Spin Disc, non-podered 1.2 CID based part identification number (PIN) identify sizes, controls, and filtration systems is included in section 5. This identification nimibering procedure is for Govemnt purposes and does not constitute a requirene
6、nt for the contractor. A document based PIN to 2. SALIENT STICS 2.1 Desian and construction. The dry cleaning unit shall use perchloro- ethylene (PE) as the cleaning solvent. door, basket/drum, solvent tanks, still, filtration system, refrigeration system, water separator, button trap, condenser, li
7、nt trap/filter, control panel, operation/maintenance manual(s), and an in-line solvent cooling system. more than 25 parts per million as established by the International Fabricare Institute (IFI) and meet or exceed all Enviromntal Protection Agency (EPA) and Occupational Safety (b) Identification ta
8、gs; (c) Information not required; and (d) ptional marking information shall not apply. The data name plate shall be made of minimum 20 gauge corrosion-resisting metal and attached to the unit by rivets, screws, or welding in such a manner that it is readily visible to the operator during normal oper
9、ating use and so as to not adversely affect the life and utility of the unit. the following information which shall be s-, engraved, or applied by photosensitive means: (a) The plate shall contain National Stock Number Pr0C;urenrent Contract Number Specification Data Manufacturer s Nam, Address, and
10、 Telephone Number Suppliers Name, Address, and Telephone NLmiber (List only if Manufacturers Model Number Government Appmved Manual Number (when specified, see 5.2). different from Manufacturer ) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-
11、50047A m 9997774 012090b 32T m A-A-50047A 3. QUALITY As- 3.1 Certification. The contractor shall certify, and maintain substanti- ating evidence, that the product offered mets the salient characteristics and requirements of this Comercial Item Description, and that the product confonir; to the produ
12、cers own drawings, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such confonnance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 3.2 Metric arodu ct. considered on an eq
13、ual basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this CID are met. dimensions and those ainiensions exceed the tolerances specif
14、ied in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 3.3 Requ latorv requ irem?nts. recovered materials in accordance with Public Law 94-580 to the max
15、imum extent practicable. Products manufactured to metric dimensions will be If a product is manufactured to metric The offeror/contractor is encouraged to use 4. PACKAGING 4.1 Packauinq, a ckinu, mrkinu and palletization. unless otherwise specified in the contract or purchase order, packaging, packi
16、ng, marking and pal.Letization shall be in accordance with ASIM D 3951, as specified for shipwnts to the Department of Defense (see 5.2). 5.1 Intended Use. clean clothes using perchloroethylene. encl.osed building. required for operation. Carniercial dry-to-dry cleaning units are designed to cyy Dry
17、 cleaning units are for use in an Electricity, steam, water, and canpressed air will be 5.2 IhcQu isition recru irementS. Acquisition documents must specify the following: a. Title, number, and date of this document. b. Size, control, and filtration systan required for the c. d. dry cleaning unit (s
18、ee 1.1). the data nmne plate when manuals are purchased urrder the contract (see 2.6). Electrical characteristics, when other than specified (see 2.2). The Government approved manual number is to be included on the Type of packaging, packing, marking and palletization requirements e. required (see 4
19、.1). 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50047A W 9999974 0120907 266 W A-A-50047A 5.3 Sources of docsuments. 5.3.1 Sources of Govemt docurrients. Copies of military and federal documents are available fm: Standardi zation Documents
20、 rer Desk Building 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 5.3.2 Sources for non-Govemnt association documents. AsIM D 3951 - Standard Practice for Cannercia1 Packaging, is The American Society for Testing and Materials (ASIM) 1916 Race Street Philadelphia, PA 19103-1187 available fm: 5.4
21、Goverment unique reuu irements. Whenever “(Govemnt unique requirement)“ is included in the title of a pragraph under “salient characteristics“, it is meant that the requirement is sawthing that is not norrrially offered to the carniercial marketplace by the manufacturer. 5.5 Part or identifvina numb
22、er (PIN). The PINS to be used for itam required by this CID are as follows: - A - 50 g-x-x-= (Example: AA50047 - C - C - 030) Size (use 3 digit number; e.g., 025 = 25 pounds) Filtration system (C or S) Controls (C or M) CID number Designates a CID 7 Provided by IHSNot for ResaleNo reproduction or ne
23、tworking permitted without license from IHS-,-,-A-A-50047A a 7777974 0120908 IT2 M A-A-50047A MILITARY IWERFSTS: Custodians Army-GL Air Force - 99 Review Activities Army-m Air Force - 50, 82 DIA - GS User Activity 8 I CIVIL AGENCY COORDINATING ACTIVITY: a GSA - Fss PREPARING mIvITY: Army-GL Project 3510-0319 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
