1、 AMSC N/A FSC 2530 INCH-POUND A-A-52168B 19 August 2013 SUPERSEDING A-A-52168A 22 September 1993 COMMERCIAL ITEM DESCRIPTION CABLE AND CONDUIT ASSEMBLY, PARKING BRAKE-STRAIGHT TYPE, BUTTON AND THREADED FITTINGS The General Services Administration has authorized the use of this commercial item descri
2、ption for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements for cable and conduit assembly, parking brake-straight type, button and threaded fittings. Cable and conduit assembly, parking brake-straight type, button and threaded fittings covered by
3、 this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as specified in the following example (see 7.1). AA52168 - 001 CID Size number 3. SALIENT CHARACTERISTICS. 3.1 Inte
4、rface and physical dimensions. Cable and conduit assembly, parking brake-straight type, button and threaded fittings supplied to this CID shall be as specified herein (see figure 1). 3.2 General requirements. This commercial item description (CID) covers several sizes of parking brake-straight type
5、cable and conduit assemblies, with button and threaded fittings. The cable and conduit assembly is, pre-stretched under a load of 1000 pounds (lbs) and is capable of withstanding a load of 2,000 lbs sustained for a period of two hours with a minimum permissible slippage of each end fitting with resp
6、ect to the cable. With load applied, cable outer sheath should not show any lateral displacement or permanent deformation of conduit Comments, suggestions, or questions on this document should be addressed to DLA Land and Maritime, Attn: VAI, 3990 East Broad Street, Columbus, OH 43218-3990 or fluidf
7、low.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52168B 2 3.3 Design and construct
8、ion. The parking brake-straight type cable and conduit assembly with button and threaded fittings shall be designed and constructed in accordance with figure 1. 3.3.1 Materials. The material used shall be as specified in figure 1. The use of recovered material made in compliance with regulatory requ
9、irements is acceptable providing that all requirements of this CID are met. 3.3.2 Slippage. The cable assembly shall be capable of withstanding a load of 2000 lbs. sustained for a period of two hours with a maximum permissible slippage of each end fitting with respect to the cable of fifteen thousan
10、dths (0.015) of an inch. With load applied, the cable outer sheath shall not show any lateral displacement or permanent deformation of conduit. The outside diameters of the conduit coils shall remain in-line. 3.3.3 Pre-stretched. Each cable assembly shall be pre-stretched under a load of 1000 lbs. 3
11、.3.4 Grease. Conduit shall be packed at assembly with grease per MIL-PRF-23827. 3.4 Marking. Cable and conduit assembly, parking brake-straight type, button and threaded fittings supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked
12、 on the unit pack shall be the CID PIN.) 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requiremen
13、ts, and promotes economically advantageous life cycle costs. 3.6 Workmanship. Cable and conduit assembly, parking brake-straight type, button and threaded fittings shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceabili
14、ty, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided s
15、hall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Certifi
16、cation. Certification must be done with the procuring activity approval. The contractor shall certify that the product offered meets the salient characteristics of the description and conforms to the producers own drawings, specifications, standards, and quality assurance practices, and is the same
17、as the product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract 6. PACKAGING. Preservation, packing, and marking shall be
18、 as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52168B 3 7.2 E
19、nvironmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemica
20、ls. The list of chemicals and additional information is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the
21、requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these Cable and conduit assembly, parking brake-straight type, button and threaded fittings to DLA Land and Maritime under the Military Parts C
22、ontrol Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-23827 Grease, Aircraft and Instrument, Gear and Actuator Screw (Copies of these documents are available online at http:/quicksearch.dla.mil or from t
23、he DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094). FEDERAL REGULATIONS FAR Federal Acquisition Regulations (FAR) (Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732
24、 North Capital Street, NW, Washington D.C. 20401.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Commercial products. As part of the market analysis and research
25、effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a li
26、st of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52168B 4 MFRs CAGE Manufacturers NAME 7S526 B.T.M.C. CORPORATION ROBERT SCHAFFER 2161 DIVIDEND DR CO
27、LUMBUS, OH 43228-3805 - USA Tel: (614) 891-1454 Fax: (614) 891-6912 7Z016 KAMPI COMPONENTS CO. INC. AMY POTTS 88 CANAL RD FAIRLESS HILLS, PA 19030-4302 http:/ AMY POTTS Tel: (267) 543-4002 FAX(215) 531-5558 Tel: (215) 736-2000 Fax: (215) 531-5541 02769 LOCKHEED MARTIN CORPORATION DBA LOCKHEED MAR
28、TIN DIV MS2 199 BORTON LANDING RD MOORESTOWN, NJ 08057-3054 http:/ DEBBIE KISTER Tel: (856) 722-4615 Fax: (856) 722-4619 JAMES V. AMATRUDI 199 BORTON LANDING ROAD MOORESTOWN, NJ 08057 - USA Tel: (856) 608-6370 Fax: (856) 608-6363 4MBX8 ALTO PRODUCTS CORP 1 ALTO WAY ATMORE, AL 36502-1018 http:/ RAN
29、DY SOWERS ONE ALTO WAY ATMORE, AL 36502 - USA Tel: (251) 368-7750 Fax: (251) 446-6750 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52168B 5 77 Government users. To acquire information on obtaining these cable and conduit assembly, parking bra
30、ke-straight type, button and threaded fittings from the Government inventory system, contact DLA Land and Maritime, ATTN: DLA Land and Maritime Call Center (NAB), P.O. Box 3990, Columbus, OH 432183990 or telephone (614) 692-2271 or (614) 692-3191.“). 7.8 Legacy. This commercial item description is a
31、 replacement for MS53060 for all federal agencies and copies of these document are available online at http:/quicksearch.dla.mil or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094). 7.9 Changes from previous issue. Marginal notations are not use
32、d in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52168B 6 inch mm inch mm inch mm 0.10 2.54 0.375 9.53 0.62 15.75 0.12 3.05 0.463 11
33、.76 1.00 25.4 0.17 4.32 0.468 11.89 1.75 44.45 0.19 4.83 0.5 12.7 2.25 57.15 0.25 6.35 0.555 14.1 2.50 63.5 0.37 9.40 0.56 14.22 10.12 257.05 PIN MS PIN Former Legacy PIN “A” DIM “B” DIM A-A-52168-1 A-A-52168-2 A-A-52168-3 A-A-52168-4 A-A-52168-5 A-A-52168-6 A-A-52168-7 MS53060-1 MS53060-2 MS53060-3
34、 MS53060-4 MS53060-5 MS53060-6 MS53060-7 7049884 7361602 8735521 8735522 8735583 8741790 44 48.88 50 53 54 59.50 51.88 28 30.38 34 34.25 38 40.75 35.88 Notes: Unless otherwise specified: 1. Dimensions are in inches. 2. Tolerances are .03 3. Asterisk indicates a minimum dimension FIGURE 1. Dash numbe
35、rs and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52168B 7 MILITARY INTERESTS CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FSS Army - AT Navy - YD Preparing activity: DLA - CC DLA - CC Review activities: Project 2530-201
36、2-002 Army-AR Navy-MC,SA NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
