1、A-A- 5 5 O 6 9 17 July 1992 COMMERCIAL ITEM DESCRIPTION T-SHIRT, ATHLETES PHYSICAL FITNESS UNIFORM (PFU) The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-T-44214. Classification. Description. The T-shirt shall have short-sleeves, a c
2、rew neck collarette, and hemmed bottom and sleeves (see figure 1). The T-shirt shall have the word ARMY in 3 inch (+ 1/4 inch) in height by 5/8 inch (2 1/16 inch) in thickness letters (see figure 2) screen printed on the front (see Table IV). The overall width of the letters shall be 12 inches (+ 1/
3、4 inch). The color of the body and collarette shall be heather gray 467. shall be made of a double thickness of ribbed cloth and shall finish 1 inch (2 1/8 inch) wide. The sleeves and T-shirt bottom shall have a hem of 1 inch (2 1/4 inch) wide. All seams shall br overedge stitched and the gage of th
4、e stitching shall be 3/16 (2 1/16 inch). base ink withstanding temperatures to 300 F. The T-shirt shall be of one type. The collarette The letters shall be black thermal plastic Sizes. The T-shirt shall be provided in the following sizes: X-Small (30-32) Small (34-36) Medium (38-40) Large (42-44) X-
5、Large (46-48) XX-Large (50-52) NOTE: The sizes X-Small, Small, Medium, Large, X-Large, and XX-Large may be abbreviated as XSM, SM, MED, LG, XLG, AND XXLG. I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be add
6、ressed to: Defense Personnel Support I l Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using 1 the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8315
7、DISTRIBUTION STATENENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5506 9 Characteristics Basic material. The cloth for the body of the T-shirt shall be a jersey knit using a cotton/p
8、olyester blend yarn conforming to the requirements specified in Table I. The cloth for the collarette of the T-shirt shall be a 1 X 1 rib knit using a cotton/polyester blend yarn conforming to the requirements specified in Table II. The cloth for the body and collarette shall be preshrunk by a mecha
9、nical process. prior to cutting the garments. shrinking process used shall not be identified by name or trademark on the finished garment or package. NOTE: capable of oxidation to sulfuric acid is prohibited. The dyes shall be chosen and applied so that the dyed and finished cloth shall contain no m
10、ore labile sulfur than shown by the standard sample when tested in accordance with end item performance testing. The pre- The use of dyes or compounds containing elementary sulfur Requirements Table I. Cloth for Bodv of T-Shirt Weight, ounces per square yard Wales per inch Courses per inch Bursting
11、strength, pounds Fiber conteat , percent: Cotton Polyes ter 5.8 2 0.5 20 (minimurn) 30 (minimum) 75 (minimum) 50 2 5 Rema inder Table II. Cloth for Collarette Characteristics Weight, ounces per square yard Wales per inch Courses per inch Bursting strength, pounds Fiber content, percent: Cotton Pol y
12、es ter 8.25 2 0.75 17 (minimum 25 (minimum 50 (minimum 50 2 5 Remainder 2 Requirements 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55069 84 9999974 O087335 Tbb A-A-5506 9 Thread. The thread for the T-shirts shall be approximately a 50/2 (ap
13、prox. 40 Tex), with minimum breaking strength of 2.7 pounds and maximum elongation of 35 percent constructed of a cotton, or a spun polyester, or a polyester-covered staple thread color shall be light grey to match the basic material for the T-shirt. The thread shall show colorfastness to laundering
14、, perspiration, and light, equal to or better than a rating of 1 polyester core, or a high tenacity, textured polyester. The i good I . Tape. weave, unbleached cotton, 3/16 ( the inspection level shall be S-3 and the AQL shall be 4.0. Defects. Material Defects and Workmanship Damage a. component par
15、t full, tight, or twisted b. any hole, cut, tear, mend, drop stitch, loose knitted, miss knit, clubby yarn, streak, knitted in waste, permanent fold, pleat, or crease c c. an omitted part d. seam; puckered, distorted, pleated, irregular or open, loose or tight stitch tension, broken or missing threa
16、d or stitch, needle chew row of stitching e. any twisted or caught part of T-shirt in any unrelated 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55 O 6 9 Shade Variations a. shaded part, off shade, wrong shade, or shade variation b. thread c
17、olor not as specified Cleanness a. spot, stain b. thread ends not trimmed Label e omitted, incorrect, illegible or misplaced Marking a. any “ARMY“ marking omitted, incorrect, illegible. or b. not size specified mi s pl a ced Measurements a. not within specified tolerance b. sleeve lengths unequal by
18、 more than 1/2 inch End Item Performance Testinq. The end item shall be tested for shrinkage as specified in Test Method 150-1987 of AATCC using normal machine cycle, (120 2 5O F) washing temperature and cotton/sturdy dryer setting (150 2 loo F). The T-shirt shall not be moistened or pressed before
19、measuring. T-shirt shall not shrink nor elongate more than 10 percent in width or length when tested. The measurements shall be taken to the nearest 0.1 inch with the T-shirt laid flat. Any dimension not within the specified tolerance shall be classified as a defect. The lot size shall be expressed
20、in units of T-shirts. The sample unit shall be one T-shirt. level (AQL), expressed in terms af defects per one hundred units, shall not exceed a total of four defects, or one and a half major defects. The completed The acceptable quality Inspection of packaainq. The sampling and inspection for the p
21、reservation, packing, marking and palletization requirements shall be ir, accordance with MIL-STD-2073-1, Table II, Preservation Inspection Provisions for Method/Submethods of MIL-P-116. The applicable defect descriptions of this Table II shall be extended to include any intermediate and shipping co
22、ntainers and the unitized load. Also included shall be a count of the specified container quantity and identification of specified contents, e.g. All items within any one cartcln shall be limited to one type, class and size. Packaqinq, Packinq, Markinq and Palletization. Preservation. Each T-shirt s
23、hall be neatly folded and placed in a commercially acceptable polyethylene bag. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55069 84 9999974 0087119 bO1 A-A-55 O 6 9 Packinq. Ninety-six T-shirts shall be packed in a fiberboard box conformin
24、g to style RSC-L, grade 275 of PPP-B-636. The inside dimensions of the box shall be approximately 24-1/2 inches in length, 16-1/2 inches in width and 12 inches in depth for X-Small to Small and 24-1/2 inches in length, 16-1/2 inches in width and 19-1/2 inches in depth for sizes Medium to XX-Large. T
25、he box shall be closed in accordance with the appendix of PPP-B-636. palletization. When specified, packed T-shirts shall be palletized on a 4-way entry pallet in accordance with load type la of MIL-STD-147. Each prepared load shall be bonded with primary and secondary straps in accordance with bond
26、ing means C and D or film bonding means F or G. Pallet pattern shall be number 3 in accordance with the appendix of MIL-STD-147. Markinq. All markings, including bar codes, on the unit peck, shipping containers and palletized loads shall be in accordance with MIL-STD-129, Source of Government Docume
27、nts. documents are available from: Copies of Kilitary and Federal Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonqovernment Documents. ANSIiACQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies sho
28、uld be addressed to American National Standards Institute, 1430 Broadway, New io.-k, NY 10018-3308.) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies siiould be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custod
29、ian: Army - GL Review Activity: Army - GL Civil Agency Coordinating Activity: GSA-FSS Preparing Activi t).: DLA-CT Project No. 84 15-08? Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-W 1 DTH - A- l LENGTH fi I FIGURE 1 11 IY S I CAI-, F 1 INESS IJN
30、 I FORM “-Si1 I RT 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5.5069 84 .II 974 0087121 2bT A-A-5506 9 e 1 I?lGUiF 2. I The thickness of each 1ctt.er shall lw 5/8 (t 1/16 incifi) style of lettering shall hrt us shown r3t)ovl. lh c 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
