1、A-A-55165 9999974 0167884 972 METRIC A- A- 55 165 23 June 1995 COMMERCIAL ITEM DESCRIPTION CONNECTORS, ELECTRICAL, SOCKETS SINGLE IN LINE MEMORY MOOULE, SINGLE VERTICAL TYPE, 64 CONTACTS The General Services Administration has authorized the use of this comnercial item description (CID), for all fed
2、eral agencies. 1. SCOPE. This CID covers the general requirements for a single, vertical inline memory module connector uith 64 contacts. This coniector provides the user with convenient low insertion and easy extraction of high density memory modules which conform to JEDEC swcifications for SIMM mo
3、dules. Connectors covered by this CID are i nte4ed for comercia I / i dust r i a I appl i cat ions. 2. CLASSIFICATION. This CID uses a classification system which is Nunber (PIN) as shown in the following example (see 7.1). AA55165 o1 S l I I I I I included in the Part or Identification A CID NUMBER
4、 S - SINGLE ROW CONTACT PLATING TYPE 3. Salient characteristics. 3.1 Design, construction and dimensions. Design, construction and dimensions shall be as specified in accordance with figure 1, table I and shall accomnodate JEDEC configured SIMM memory modules. 3.2 Contacts. Code G contacts (dash nun
5、ber -01) are formed of a high conductivity, high strength copper alloy with gold over nickel plating in the contact area. Code T contacts (dash nunber -02) are formed of a high conductivity, high strength copper alloy uith tin/lead plating over all areas. 3.3 Comector housing. withstanding temperatu
6、res of vapor phase, infrared, or wave type soldering assembly processes. 3.4 Contact stress. 3.5 Misconnection. Built in polarization eliminates misconnection of SIMM module to connector. Additional polarization feature to align socket to printed wiring board for simplification of assembly. 3.6 Diel
7、ectric withstanding voltage. When tested at 1,000 V ac, there shall be no breakdown of insulation or leakage current in excess of 5 mA between adjacent contacts for one minute. 3.7 Operating temperature. Connector housings are made from high temperature thermoplastic material capable of The connecto
8、r design provides anti-stress protection for contacts. The operating temperature range shall be from -55C to +105C. Beneficial cwrments, .recommendations, additions, deletions clarifications, etc. and any other data which may improve this document should be sent to: Defense Electronics Supply Center
9、 ATTN: DESC-ELDI, 1507 Wilmington Pi.ke, Dayton, OH (513) 296-8868. 45444-5765, or telephone (513) 296-5391, or facsimile (FAX) AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted wi
10、thout license from IHS-,-,-A-A-55165 9999974 0367885 809 . r A-A-55165 TABLE i 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-5.5165 = 74 03b7886 745 A - A -55165 I SINGLE FIGURE 1. Printed board layout. 3.8 Vibration. The connector, or hardw
11、are when assembled to the connector, shall exhibit no evidence of breaking, cracking, or loosening of parts when subject to vibration of 10-55-10 Hz traversed in 1 minute at .O6 inch total excursion for 2 hours in each of 3 mutually perpendicular planes. 3.9 Physical shock. The connector or hardware
12、 when assembled to the connector, shall exhibit no evidence of breaking, cracking, or loosening of parts when subject to 50 gs sau-tooth wave shock of 11 milliseconds duration, 3 shocks in each direction applied along the 3 mitually perpendicular planes for a total of 18 shocks. 3.10 Durability. The
13、 connector shall be capable of withstanding 25 module insertion and withdraual cycles without a reduction in connector performance. 4. REGULATORY REQUIREMENTS. 5. QUALITY ASSURANCE PROVISIONS. 5.1 Responsibility for inspections. The contractor is responsible for the performance of all inspection, ex
14、amination and test requirements specified in the contract or purchase order. The contractor may use his or any other facilities suitable for inspection requirements specified in the contract or purchase order, unless otherwise disapproved by the procurement activity. The procurement activity reserve
15、s the right to perform any of the inspections set forth in the contract or purchase order uhere such inspections, examinations and tests are deemed necessary to assure supplies and services conform to prescribed requirements. 5.2 Contractor certification. The contractor shall certify and maintain ob
16、jective quality evidence that the product offered mets the requirements of this CIO and that the product conforms to the producers oun drawings, specificatims, standards, quality assurance practices, and is the same as the product provided as a bid sample. The procurement activity reserves the right
17、 to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. This section is not applicable to this CID. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-
18、55165 9Ft4 OLb7 b8L A- A - 55 165 5.3 Certificate of compliance. Each contractor desiring to be listed as a suggested source of supply shall submit a DESC certificate of conpliance to DESC-ELDI. This certificate shall state that the contractors product meets all the requirement of this CID. In addit
19、ion, a certificate of compliance shall accompany all connectors supplied to this CID. 6. Packaging. 6.1 Preservation. packaging, packing, labeling. and marking. Preservation, packaging, labeling, and marking shall be as specified in the contract or purchase order. 7. NOTES. 7.1 W. The PIN should be
20、used for goverrment purposes to buy comnercial products to this CID. See 2.1 for PIN format. 7.2 Source of documents. Other Publications Joint Electron Devices Engineering Council (Application for copies should be addressed to the JEDEC Solid State Products Engineering Council, 2001 Pennsylvania Ave
21、nue, N.U., Washington, D.C. 20006). (Industry association specifications and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 7.3 Government users. To acquire information on obtaining these connectors from t
22、he Government inventory system, contact Defense Electronics Supply Center, ATTN: DESC-EON, 1507 Wilmington Pike, Dayton, OH 45444-5522, or telephone (513) 296-5009. 7.4 ORDERING DATA. The contract or purchase order shall specify the following: a. CID nurber, revision and CID PIN. b. uality assurance
23、 provisions. c. Packaging requirements. 7.5 Suggested sources of suppiy. added as they become available. A suggested source of supply is listed herein. Additional sources will be (see table I) AA55165 CAGE 00779 822286- 1 821957-1 4 Provided by IHSNot for ResaleNo reproduction or networking permitte
24、d without license from IHS-,-,-A-A-55165 m 9999974 0367888 518 A-A-55165 Vendor CAGE nunber 00779 Vendor name and address AMP, Incorporated Eisenhower Boulevard Harrisburg, PA 17105 CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Preparing Activity: DLA-ES Project 5935-3941-03 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
