1、A-A-55230 W 9999934 Ol15b038 526 A-A-55 23 O 23 September 1993 COMMERCIAL ITEM DESCRIPTION SLACKS, WOMENS HOSPITAL DUTY UNIFORM (HDU) The General Services Administration has authorized the use of this commercial item description in preference to MIL-S-44292. Abstract. This commercial item descriptio
2、n covers womens slacks made of twill weave, polyester/cotton cloth. They are intended to be worn as a hospital duty or food handler uniform by female personnel of the Department of Defense. Salient characteristics. have a slide fastener fly front with a snap fastener, elasticized waist and 2 back da
3、rts facing towards the seat seam. shall be pressed and creased in the center with the seams matching at bottom and in the crotch. All seams shall be overedged. Material. The basic material shall be a 2/1 left-hand twill cloth that is a blend of 65 i 5 percent polyester. The remaining percentage shal
4、l be combed and carded cotton, spun into singles yarn. The cloth shall be desized, scoured, mercerized, bleached, heat-set, and treated with a durable press finish. The material shall conform to the requirements specified in Table I. The straight leg hemmed slacks shall The legs Beneficial comments
5、(recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSC, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardizatio
6、n Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 8410 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i A
7、-A-55230 = 9999974 015b079 462 A-A-55 2 3 O TABLE I. - Physical requirements Characteristic Requirement Test Method (Minimum) Weight (min.) 6.8 oz./sq. yd. ASTM-D 3776 Option C Yarns per inch (min.) Warp Filling 116 47 ASTM-D 3775 ASTM-D 3775 Colorfastness to: Laundering (after 3 cycles) Class 4 Cla
8、ss 4 “Good“ 2/ A/ S/ i/ A/ 5/ - AATCC 61 Test 3A AATCC 15 AATCC 16A Perspiration Light Breaking strength (lbs. min.) Warp Filling 170 lbs. (min.) 120 lbs. (min.) ASTM-D 5034 II Tearing strength (min.) Warp Filling 5.0 4.5 ASTM-D 1424 II Dimensional stability +2% in either direction any spot or stain
9、 (outside); raw edges, open seams, thread ends not removed or loose tension resulting in loose seams; any material defects, distorted parts or poor workmanship; any component part omitted; label missing, incorrect, or illegible; measurement of item not as specified; bar code omitted or not readable
10、by scanner; human- readable interpretation (HRI) omitted or illegible; not visible or folded, package item; causes damage to the item. Dimensional examination. The finished slacks shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classifie
11、d as a defect. The sample unit shall be one pair of slacks. Packauinu examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. EXAMINE DEFECT Marking Omitted; incorrec
12、t; illegible; (exterior and interior) of improper size, location, or method of application Materials Workmanship Content Palletization Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper t
13、aping, or inadequate stapling Number of items in container is more or less than required NSN shown on one or more items is not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified 6 Provided by IH
14、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55230 W 9999974 O356084 82T A-A-55 2 3 O Preservation, Packinq, and markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government documents. Copies of Milita
15、ry and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of non-Government documents ASTM-D 1424 - Standard Test Method for Tearing Strength ASTM-D 2165 - Standard Test Method for pH ASTM-D 3776 - Standard Test
16、Method for Mass per Unit Area (Weight) of Woven Fabric ASTM-D 3787 - Standard Test Method for Bursting Strength of Knitted Goods-Constant-Rate-of-Traverse (CRT) Ball Burst Test ASTM-D 5034 - Standard Test Method for Breaking Strength (Applications for copies should be addressed to American Society F
17、or Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) 0 AATCC 15 - Colorfastness to PersDiration AATCC 16 AATCC 61 - Colorfastness to Laundering, Home, and Commercial: Accelerated AATCC 124 - Appearance of Fabrics after Repeated Home Launderings AATCC 135 - Dimensional Changes in
18、 Automatic Home Laundering of Woven and Knit Fabrics - Colorfastness to Ligh; (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215.) Custodian: Air Force - 99 Army - GL Review Activity: Air Force - 82 Army - MD Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT Project No. 8410-0804 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
