1、 A-A-55441 W 9999974 0369703 8T4 m SIZE 1 2 3 4 5 6 A-A-5544 1 21 December 1995 COMMERCIAL ITEM DESCRIPTION WASHER-EXTRACTOR, COMMERCIAL FOR DECONTAMINATION OF PROTECTIVE EQUIPMENT AND CLOTHING CAPACITY CYLINDER CYLINDER diameter X depth (ins.) (cubic feet) 35 30 X 15 6 50 30 X 20 8 75 36 X 20 12 95
2、 36 X 24 14 125 . 42x26 20 250 50 X 30 34 MINIMUM LOAD (lb.) DIMENSIONS (min.) VOLUME (min.) The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE 1.1 Description. This document covers washer-extractors with capacities rangi
3、ng from 35 pounds to 250 pounds dry weight of soiled items. Machines are electrically operated and micro-processor controlled, with single compartment, end loading, cylinders. 1.2 Intended use. Washer-extractors described in this CID are for use in decontaminating protective clothing and other prote
4、ctive equipment worn by firemen, emergency response teams, and hazardous materials clean up crews. 2. CLASSIFICATION 2.1 m. Sizes of Washer-extractors shall be in accordance with Table I. Each size shall conform to the capacities and cylinder dimensions and volumes as stated in Table I. TABLE 1. 2.2
5、 lyp-e. The washer-extractors shall be of the following spes as determined by supply chemical dispensing method. Type 1 = Liquid supply. Type 2 = Dry (powder or flake) supply. Type 3 = Combination liquid and dry. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and an
6、y data which may improve this document should be sent to: Defense Supply Center Richmond(DSCR), AT“: DSCR-VCA, 8000 Jefferson Davis Highway, Richmond, VA 23297-5768. AMSC NIA FSC 3510 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling S
7、ervicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55441 = 9999974 03a9702 730 A-A-55441 3. SALIENTCH ARACTERIS TICS 3.1 Standard product . Washer-extractors hished under this CID shall be the manufacturers current standard product including
8、accessories and optional components that are offered to the commercial market. All accessories and options shall be identified with proposals tendered to the government in response to solicitations citing this document. 3.2 Desim and construction. The washer-extractors shall be single compartment, e
9、nd loading designs employing shell and cylinder design configuration. Sizes and capacities shall be as stated in paragraph 2.1 and shall be based on not more than six pounds of soiled linen per cubic foot of cylinder volume (gross). Self-diagnostic, programmable, microprocessor controls shall be use
10、d for all sizes of washer-extractors to store field programmable wash formulas for automatically monitoring and controlling, water temperature, water level, wash cycles, cylinder reversals, automatic chemical injection, load distribution prior to extraction, and extraction. A minimum of 10 pre- prog
11、rammed wash formulas shall be provided for decontaminating protective clothing and gear. The microprocessor shall be capable of storing no fewer than 30 wash programs. 3.2.1 Codes and standards. Washer-extractors shall conform to the applicable requirements of the codes and standards specified in 3.
12、2.1.1 through 3.2.1.4. 3.2.1.1 NFPA. Wiring shall conform to National Fire Protection (NFPA) Standard No. 70, The National Electrical Code. 3.2.1.2 lVF,MA. Motor controllers, switches, relays, and time delays shall conform to performance requirements of National Electrical Manufacturers Association
13、(NEMA) Standard Publications No. ICs 1-1993, Industrial Controls , General Requirements, and No. ICs 3-1993, Industrial Control and Systems Factory-built Assemblies. 3.2.1.3 ANSI. Washer-extractors shall conform to the requirements of American National Standards institute (ANSI) Standard 28.1 , Safe
14、ty Requirements for Commercial Laundry and Dry Cleaning Equipment and Operations. 3.2.1.4 OSHA. Washer-extractors shall conform to Occupational Safety and Health Standards Act (OSHA) 29 CFR 1910. 3.2.2 Mated.s. Materials not definitely specified herein shall be of the quality specified by the manufa
15、cturer and shall conform to the manufacturers own drawings, specifications, standards, and quality assurance procedures. 3.2.2.1 &d&ins and electn c wire. Ele&cal conduit shall be liquid tight flexible conduit with matching fittings and connectors. Electric wire shall be stranded copper, heat-resist
16、ant grade, thermoplastic insulated. Solid (nonstranded) wire shall not be used. 3.2.2.2 Fasteners. Threaded fasteners and rivets shall be made of types 304,304L or 3 16 corrosion resistant alloy steel conforming to compositions stated in ASTM A 167, Stainless and Heat-Resisting Chromium-Nickel Steel
17、 Plate, Sheet and Strip. 3.2.2.3 -. The cylinder shall be constructed of type 304,304L7 or 3 16 stainless steel conforming to compositions stated in ASTM A 167. 3.2.2.4 Finish and CO lor. The washer-extractors shall be finished according to the manufacturers standard commercial practice. 3.3 Perform
18、ance . The washer-extractors shall conform to performance requirements expressed in paragraphs 3.3.1 Page 2 through 3.3.4. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-554411 m 9999974 O1169703 b77 m A
19、-A-55441 3.3.1 Vibration. Washer-extractors shall be designed to isolate and minimize vibration transmitted to the floor and surrounding building structure during the extraction cycle. The amplitude of the vibration at the base of the washer- extractor which is in contact with the floor shall not ex
20、ceed 0.005 inch total indicator reading taken with a mass vibrometer when the washer-extractor is operating in the extraction cycle at full rated load and maximum extraction speed with a five percent load unbalance in one pocket of the cylinder. Vibration isolation design shall not require unusual o
21、r special foundation construction materials. Anchor bolts shall be selected from readily available materials, grades and sizes to handle anticipated dynamic loads. 3.3.2 m. Noise level shall not exceed 85 decibels (A scale), when measured at the operators position (in front of and within 36 inches o
22、f the control panel). 3.3.3 Cylinder reversing . Cylinder revolutions in one direction shall not vary by more than five percent fkom cylinder revolutions in the opposite direction between reversals. 3.3.4 Pre-extract load distribution. Pre-extract load distribution shall be automatic and continue at
23、 distribution speed until any unbalance situation is reduced to an acceptable level for high speed centrifuging of the wash load. 3.4 Order of precedence. In the event of a conflict between the text of this CID and the referenced documents cited herein, the text of this CID shall take precedence. No
24、thing in this CID, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3.5 Data. Each machine shall include a copy of the manufacturers standard “owner/operator manual“ applicable to the machine. The manual shall include instructions for operating
25、the machine, safety precautions, preventative and routine maintenance instructions, and installation instructions which identi utility interface and machine foundation details. This data shall be the same information that is normally provided with similar machines sold in the commercial market. 3.6
26、Metric moduct. Products manufactured to metric (SI) dimensions shall be considered on an equal basis with those manufactured using inch-pound units of measure, provided they fall within the specified tolerances using conversion tables contained in the latest revision of ASTM E 380, Standard Practice
27、 for Use of the International System of Units (SI), and all other requirements of this Commercial Item Description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in inch-pound units, a request should be made to the contracting officer
28、to determine if the product is acceptable. 4. REGULATORY REOUIREMENTS 4.1 OccuDational Safety. Washer-extractors shall conform to Occupational Safety and Health Act (OSHA), 29 CFR 1910 (see 3.2.1.4). 4.2. Recovered materials. The offeror/contractor is encouraged to use recovered materials in accorda
29、nce with Public Law 94-580 to the maximum practical extent. Recycled or reclaimed materials may be used in the construction of the equipment described herein. Recycled and reclaimed materials shall consist of previously used material which has been reprocessed to become a source of new raw materials
30、. Under no conditions or circumstances shall the contractor submit to the Government for acceptance reconditioned or rebuilt components as a part of the equipment described herein. 5. DUALITYASSURA NCE PROVISIONS 5.1 Contractor certification. The contractor shall certifi and maintain substantiating
31、evidence that the product Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55 441 m 9999974 0169704 503 A-A-55441 offered meets the salient characteristics of this Commercial Item Description, and that the
32、 product conforms to the producers own drawings, specifications, standards, and quaiity assurance practices and is the same as the product offered for sale in the commercial marketplace. When specific quality assurance provisions are specified for any commercial characteristic the contractor shall m
33、aintain records resulting from his inspection(s) conducted in accordance with the specific quality assurance provisions. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided under the provisions of the contract. Th
34、e government reserves the right to audit the contractors quality assurance records. 5.2 Successful commercial operation, No item of equipment offered under this CID shall be acceptable unless the manufacturer has marketed equipment of the same size (similar capacity) and type in a commercial environ
35、ment for a minimum period of one year. Equipment installed for test purposes in a manufacturers plant or test laboratory shall not be considered as complying with this requirement. 5.3 p. Each machine shall bear an alpha-numeric code to indicate the manufacturers plant where produced and the date th
36、at production occurred. This encoded information shall be permanently stamped or affixed to the machine. 5.4 Warrany. Unless otherwise specified in the contract, the manufacturers standard commercial warranty terms shall apply. The warranty shall become effective with the date of startup of the equi
37、pment after installation is complete. 6. PACKAGING 6.1 Packapins pack&!, alletization and marking. Unless otherwise specified (see 7.2) packaging, packing, and pailetization shall be in accordance with ASTM D 3951. Washer-extractors shall be shipped fully assembled. Blocking or special shipping stra
38、ps to protect the cylinder or other sensitive components may be used at the manufacturefs discretion. 6.2 Overseas m ilitary shipment !?oveniment unique requirement). When specified in the contract or purchase order, washer-extractors shall be preserved, packed, and marked for Levels A, B, or C of p
39、rotection in accordance with the applicable requirements of MIL-L-3 153, Laundry and Dry Cleaning Machinery and Equipment, Packaging of (see 7.2). 7. NOTES 7.1. Commercialem cert ification. When this CID is used for procurement, the commercial item certification clause must appear in the solicitatio
40、n. 7.2 Orderinw Data . The following information is required when ordering items covered in this CID: a. Title, number, and date of this document. b. Packing and packaging required (see 6.1 and 6.2). c. Quantity. d. Size and Type (see 2.1 and 2.2). e. Electrical requirements (voltage, phase and hert
41、z). f. PIN (see 7.3). Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55 441 9999974 0369705 44T A-A-5544 1 7.3 Pari or Identieing Number PIN) . The following PIN procedure is for government purposes and
42、does not constitute a requirement for the contractor. A CID based PIN to identi the item(s) procured to this CID shall be constructed as follows: A-XXXXX-X-X-XXXXXX Phase (1 or 3) Hertz (50 or 60) Voltage (3 digits) Type (1,2, or 3) Size (1 - 6) CID Number A Indicates CID 7.4 Referenced documents. C
43、opies of referenced documents are available fiom the following sources: 7.4.1 Government Docum ents. Standardization Documents Order Desk 700 Robbins Avenue Building 4, Section D Philadelphia, PA 191 11-5094 7.4.2 Non-governmen t documents. American National Standards Institute (ANSI) American Natio
44、nal Standards Institute 11 West 42nd Street New York, NY 10036 National Electrical Manufacturers Association NEMAJ National Electrical Manufacturers Association 2101 L Street, NW, Suite 300 Washington, DC 20037 ASTM (formerly American Society for Testing and Materials) ASTM 100 Ban Harbor Drive West
45、 Conshohocken, PA 19428-2959 National Fire Protection Association NFPAJ National Fire Protection Association One Batterymarch Park QUCY, MA 02269-9 1 O 1 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-554
46、41 7.5 Sub-iect term kev w ord) I is t. Washer extractor Bunker gear Decontamination Protective equipment Protective clothing Firemen Hazardous materials 7.6 Sources of supplv. A partial list of manufacturers of washer-extractors described herein follows: UNIMAC CO. INC. 3595-T, Industrial Park Driv
47、e Marianna, FL 32446-9458 PELLERIN-MILNOR COW. Dept. TR Kenner, LA 70063-0400 PRIMUS, INC. 28 Mitchel Road, Bldg. B Ipswich, MA O1938 G. A. BRAUN, INC. 461 E. Brighton Ave, P. O. Box 70 Syracuse, NY 13205-0070 AMERICAN LAUNDRY MACHINERY, INC. 5050 Section Avenue Cincinnati, OH 45212-2099 MILITARY IN
48、TEREST Custodians Air Force - 99 Navy - YDl Army - GL Beview activities Army-MD CIVIL AGENCY COORDINATING ACTIVITY: GSAESS-6FET-CO PREPARING ACTIVITY: DLA-GS (Project 35 10-0341) Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
