1、INCHPOUND AA55563/25A 25 June 2013 Superseding AA55563/25 10 May 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, OPEN ENDED, WITH 2 MOUNTING HOLES, FOR USE WITH HEAT SINKS The General Services Administration has authorized the use of this commercial it
2、em description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of commercial item description (CID) AA55563. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item
3、description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA55563 CID number /25 Applicable CID specification sheet Material H Card holder width/ board thickness XX Length formerly 1/4 H
4、), “B“ (beryllium copper of temper TH01; formerly 1/4 HT) or “D“ (stainless steel). The material type designator and shall be included in the PIN. Material thickness. The beryllium copper thickness shall be .008 .002 inch (0.20 0.05 mm). Card holder width/board thickness. The card holder width/board
5、 thickness is variable and based on the distance the card guide is mounted from the heat sink side wall (see figure 1). To obtain optimum clamping force, the centerline of the card guide installation holes in the heat sink shall be spaced .093 inch (2.36 mm) plus the thickness of the circuit card as
6、sembly printed board thickness from the side wall. The applicable card holder width/board thickness designator for this CID specification sheet is “H“. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/25A 2 Inches mm Inches mm
7、 Inches mm Inches mm .005 .02 .070 0.13 0.51 1.78 .093 .105 .125 2.36 2.67 3.18 .156 .180 .198 3.96 4.57 5.03 .250 .310 .520 6.35 7.87 13.21 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two
8、 place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 1. Card holder design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/25A 3 Overall length. Overall length is shown on figure 1 as dimension “L“, and is
9、displayed in table I herein. Applicable overall length designator “10“, “15“, “20“, “25“, “30“, “35“, “40“, “45“, “50“, “55“, or “60“ shall be included in the PIN. Finish. Finish types shall be defined in AA55563. Applicable finish materials designator “C“ (copper plate), “D“ (black ebonal) “E“ (gol
10、d plate), “F“ (nickel plate), “H“ (silver plate), “J“ (zinc, yellow chromate), or “K“ (no finish) or “R“ (zinc, clear chromate) are available for material type designators “A“ (beryllium copper of temper TD01) and “B“ (beryllium copper of temper TH01)“. Finish designator “G“ (passivate) is the only
11、finish available for material type designator “D“ (stainless steel). The finish designator shall be included in the PIN. Mounting hole spacing. Mounting hole spacing is shown on figure 1 as dimension “M“. Dimension “M“ is displayed in table I herein. TABLE I. Length and hole spacing. 1/ 2/ PIN desig
12、nator for overall length Dimension “L“ .020 (0.51) Dimension “M“ .005 (0.13) Inch mm Inch mm 10 1.0 25 .750 19.1 15 1.5 38 1.25 31.8 20 2.0 51 1.75 44.5 25 2.5 64 2.25 57.2 30 3.0 76 2.75 69.9 35 3.5 89 3.25 82.6 40 4.0 102 3.75 96.3 45 4.5 114 4.25 108.0 50 5.0 127 4.75 120.7 55 5.5 114 5.25 133.4
13、60 6.0 152 5.75 146.1 1/ Dimensions are in inches. Millimeters are given for general information only. 2/ Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 (0.25 mm) for three place decimals. NOTES. PIN. The PIN should be used for Government purposes to buy
14、 commercial products to this CID specification sheet. See the classification/part identification number for PIN format example. AA55563 Source of documents. Commercial Item Description AA55563 Holder, Electrical Card, Metal Card Guide, General Requirements for. (Copies of these documents are availab
15、le online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA55563. Provided by IHSNot for ResaleNo reproduction or networking per
16、mitted without license from IHS-,-,-AA55563/25A 4 Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these
17、manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufactu
18、rer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: Part number (P/N) supersession data. These CID specificati
19、on sheet PINs supersedes the following manufacturers P/Ns as shown in table II. The CID PINs listed in table II cover the different lengths available. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE II. Commercial part number supersess
20、ion data. CID PIN: AA55563/25HXX& 1/ Manufacturers 2/ Material type Card holder width/board thickness Overall length designator Finish 3/ CAGE 18915 4/ A H 10 3/ 371B2P A H 15 3/ 371B3P A H 20 3/ 371B4P A H 25 3/ 371B5P A H 30 3/ 371B6P A H 35 3/ 371B7P A H 40 3/ 371B8P A H 45 3/ 371B9P A H 50 3/ 37
21、1B10P A H 55 3/ 371B11P A H 60 3/ 371B12P B H 10 3/ 371BH2P B H 15 3/ 371BH3P B H 20 3/ 371BH4P B H 25 3/ 371BH5P B H 30 3/ 371BH6P B H 35 3/ 371BH7P B H 40 3/ 371BH8P B H 45 3/ 371BH9P B H 50 3/ 371BH10P B H 55 3/ 371BH11P B H 60 3/ 371BH12P See footnotes at end of table.Provided by IHSNot for Resa
22、leNo reproduction or networking permitted without license from IHS-,-,-AA55563/25A 5 TABLE II. Commercial part number supersession data Continued. CID PIN: AA55563/25HXX& 1/ Manufacturers 2/ Material type Card holder width/board thickness Overall length designator Finish 3/ CAGE 18915 4/ D H 10 G 37
23、1CR2 D H 15 G 371CR3 D H 20 G 371CR4 D H 25 G 371CR5 D H 30 G 371CR6 D H 35 G 371CR7 D H 40 G 371CR8 D H 45 G 371CR9 D H 50 G 371CR10 D H 55 G 371CR11 D H 60 G 371CR12 1/ See classification/part identification number for symbol representation. 2/ The manufacturers part number shall not be used for p
24、rocurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/
25、 Finish materials designator “C“, “D“, “E“, “F“, “H“, “K“, “J“, or “R“ are available for this material type. 4/ Manufacturer CAGE 18915 superseded part number suffix letter “P“ denotes finish material. Guidance on use of alternative parts with less hazardous or nonhazardous materials. This CID speci
26、fication sheet provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. Changes from previous issue. The margins of this specification are marked with ve
27、rtical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the e
28、ntire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/25A 6 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS: Army CR Navy
29、EC Preparing activity: Air Force 85 DLA CC DLA CC Review activity: Project: 59982012055 Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
