1、A-A-59284 9018054 0004483 932 E INCH-POUND A-A-5 9284 17 March 1999 SUPERSEDING W-S-570B 19 October 1990 COMMERCIAL ITEM DESCRIPTION SOLDEWG IRON, ELECTRIC The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commerci
2、al item description (CID) covers electrically powered hand soldering irons which are intended to be used for manual soldering operations. 2. CLASSIFICATION. The soldering iron shall be of the following types, styles, and sizes. The type and size to be furnished shall be as specified (see 7.2(b). Typ
3、e I - Wattage controlled Style A - Fixed wattage output Style B - Variable wattage output Size 25 - 25 watts Size 30 - 30 watts Size 35 - 35 watts Size 40 - 40 watts Size 50 - 50 watts Size 60 - 60 watts Size 80 - 80 watts Type II - Temperature controlled Style C - Fixed temperature output Style D -
4、 Variable temperature output Size 100 - 100 watts Size 200 - 200 watts Size 300 - 300 watts Size 400 - 400 watts Size 500 - 500 watts Size 600 - 600 watts Size 700 - 700 watts _ _ I Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other I I data which may impr
5、ove this document should be sent to: Defense Supply Center Richmond, ATTN: DSCR-VCA, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610. AMSC N/A FSC 3439 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesProvided by IHSNot
6、for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59284 3. SALIENT CHARACTERISTICS 3.1 General requirements. Unless otherwise specified (see 7.2(c), the soldering iron shall operate from a 120-volt, single-phase, 60-hertz circuit. The leakage voltage measured fiom th
7、e soldering iron tip to the ground shall not exceed 0.002 volts RMS. Resistance between the tip of a hot soldering iron and the ground shall not exceed 5 ohms. Unless otherwise specified (see 7.2(d), a stand assembly and tip wiping sponge shall be provided. The soldering iron shall be equipped with
8、a 4 1/2 to 8-foot flexible 3-conductor power cord. The power cord ground plug shall meet the requirements of figure 5- 1 5 of National Electrical Manufacturers Association (NEMA) WD-6. 3.2 Twe I, wattage controlled outriut. The type I soldering iron shall supply a controlled wattage to the tip. The
9、wattage shall correspond to the required size. The style A soldering iron shall supply a fixed wattage to the tip. The style B soldering iron shall have a dial or slide switch for adjusting wattage output. Unless otherwise specified (see 7.2(e), the wattage supplied to the tip shall be variable fiom
10、 at least 30 to 100 percent of soldering iron wattage capacity. 3.3 Type II, temperature controlled output. The type II soldering iron shall regulate the tip at a constant temperature to within +lo degrees Fahrenheit of the setpoint. Unless otherwise specified (see 7.2(f), the type II style C solder
11、ing iron shall have a setpoint of not less than 600 degrees Fahrenheit. The type II style D soldering iron shall allow the tip temperature to be controlled over a continuous range. Unless otherwise specified (see 7.2(g), the soldering iron shall allow the tip temperature setpoint to be controlled ov
12、er a temperature range from at least 350 to 850 degrees Fahrenheit. 3.4 Soldering; tin Unless otherwise specified (see 7.2(h), the tip shall be iron plated. If required, the tip shall additionally be nickel or chrome plated as specified (see 7.2(i). The shank diameter shall be 1/8, 3/16, 1/4, 5/16,3
13、/8, 1/2,5/8,7/8, or 1 inch as specified (see 7.2 u). The tip shape shall be a pencil, pyramid, chisel, screwdriver, conical or conical bevel as specified (see 7.2( k). 3.5 Performance. The soldering iron shall meet the performance requirements of Underwriters Laboratories (UL) 499. 4. REGULATORY REQ
14、UIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 or the Federal Acquisition Regulation (FAR). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
15、e from IHS-,-,- A-A-59284 9018054 0004485 i05 II A-A-59284 , 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this comercial item description; conform to the producers own drawings, specifications, standards, and quality assuran
16、ce practices; and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.1.1 Verification of conforrnance. Suitable verification of conformance to the performance requirements of UL499 shall be either the UL label or c
17、ertification of such conformance by an accredited testing laboratory satisfactory to the Government. 5.2 Warranty. Unless otherwise specified (see 7.2(1), the manufacturers standard commercial warranty, terms, and conditions shall apply. 6. PACKAGING. Preservation, packing, and marking shall be as s
18、pecified (7.2(m) in the contract or purchase order. 7. NOTES 7.1 Sources of documents. 7.1.1 Government documents. Copies of paragraph 24.403 of the FAR may be obtained fiom the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. 7.1.2 Nongovernment documents. Copies
19、of industry standards referenced in this CID may be obtained fiom the following addresses: National Electrical Manufacturers Association (NEMA) NEMA WD-6 Wiring Devices - Dimensional Requirements Applications for copies should be sent to the National Electrical Manufacturers Association, 1300 North
20、17th Street, Suite 1847, Rsslyn, VA 22209. Underwriters Laboratories (UL) UL 499 Standard for Safety for Electric Heating Appliances Applications for copies should be sent to the Underwriters Laboratories, Inc., 333 Pfingsten Rd., Northbrook, Illinois 60062-2096. 3 Provided by IHSNot for ResaleNo re
21、production or networking permitted without license from IHS-,-,-A-A-57284 9038054 0004486 643 A-A-59284 7.2 Ordering data. Acquisition documents must speci& the following: a. Title, number, and date of this document. b. Type, style, and size of soldering iron required (see 2). c. Electric power requ
22、irements, if different (see 3.1). d. Stand assembly and sponge, if different (see 3.1). e. Soldering iron wattage, if different (see 3.2). f. Soldering iron setpoint, if different (see 3.3). g. Soldering iron tip temperature setpoint range, if different (see 3.3). h. Iron plating, if different (see
23、3.4). i. Additional plating, as specified (see 3.4). j. Tip shank size, as specified (see 3.4). k. Tip shape, as specified (see 3.4). 1. Warranty, if different (see 5.2) m. Packaging requirements, as specified (see 6). 7.3 Part identification number (PIN). The following part identification numbering
24、 procedure is for Government purposes and does not constitute a requirement for the contractor. I CIDnumber MILITARY INTERESTS: Custodians Army-AR Air Force - 99 Navy - SH PREPARING ACTIVITY: DLA - GS (Project 3439-0884) Reviewers Air Force - 84 Navy - MC, YD 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
