1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-0557, or facsimile (FAX) (614)
2、692-6939. AMSC N/A FSC 5950 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-59696 1 October 2001 COMMERCIAL ITEM DESCRIPTION COIL, RF, CHIP, FIXED, LOW PROFILE, SURFACE MOUNT The General Services Administration has authorized the use of this commercia
3、l item description (CID) for all federal agencies. 1. SCOPE. This CID covers the general requirements for a radio frequency coil. Coils covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION. This CID uses a classification system which is included in the Part Iden
4、tification Number (PIN) as shown in the following example (see 7.1). AA59696 - 001 F CID number Dash number (see table I) Inductance Tolerance (see table II) 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Coils supplied to this CID shall be as specified herein. (see figure 1). 3.
5、2. Electrical characteristics. The electrical characteristics shall be as specified in table I. 3.3 Weight. The weight shall be no greater than 0.5 gram maximum. 3.4 Operating temperature range. The operating temperature range is 40C to +125C. 3.5 Temperature rise. DC current rating for a 15C rise.
6、3.6 Altitude. The maximum altitude is 70,000 feet. 3.7 Marking. Coils supplied to this CID shall be marked with the manufacturers standard commercial PIN. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59696 2 Dimension INCHES MM A B C D E F G H
7、 .076 - .084 .095 - .105 .055 Max. .115 Max. .110 Max. .010 - .025 .015 - .025 .020 Ref. 1.93 2.13 2.41 2.67 1.40 Max. 2.92 Max. 2.79 Max. 0.25 0.64 0.38 0.64 0.508 Ref. NOTES: 1. Dimensions are in Inches. 2. Metric equivalents are listed for general information only. FIGURE 1. Configuration and dim
8、ensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59696 3 TABLE I. Electrical characteristics. CID dash number AA59696- Inductance (nH) ( 50 MHz) Tolerance (%) Q min ( 500MHz) SRF min (MHz) DCR Max (Ohms) IDCMax (mA) 001 4.7 20, 10, 5 42 7
9、500 .15 600 002 8.2 20, 10, 5 50 5000 .22 600 003 15 20, 10, 5 57 3000 .22 600 004 20 20, 10, 5 72 2400 .33 600 005 30 20, 10, 5, 2 69 2400 .38 600 006 40 20, 10, 5, 2 67 2000 .43 600 007 50 10, 5, 2 72 1900 .48 600 008 60 10, 5, 2, 1 75 1800 .52 600 009 70 10, 5, 2, 1 68 1700 .55 510 010 80 10, 5,
10、2, 1 75 1400 .56 510 011 90 10, 5, 2 85 1400 .61 500 012 100 10, 5, 2 60 1000 .63 480 TABLE II. Inductance tolerances Code Tolerance (percentage) F G J K M 1 2 5 10 20 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in ac
11、cordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance pra
12、ctices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the product to be provided under this CID: Provi
13、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59696 4 a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b. The company must have sold 1,000 units meeting this CID in the c
14、ommercial marketplace over the past 2 years. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Commercial
15、 and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these inductors to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.3 Ordering data. The contract or order should specify the following: a
16、 CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.4 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation an
17、d coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs name and a
18、ddress 02113 Coilcraft Inc1102 Silver Lake Road Cary, Illinois 60013-1658 Phone number (847) 639-2361 Uniform Resource Locator (URL): Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59696 5 7.5 Part number (P/N) supersession data. This CID super
19、sedes the following manufacturers P/Ns as shown. This information is being provided to assist in reducing proliferation in the government inventory system. TABLE III. P/N supersession data. 1/ CID dash number (see table I) AA59696- Vendor commercial PIN 2/ CAGE 02113 001* 1008CT-040-X*B* 002* 1008CT
20、080-X*B* 003* 1008CT-150-X*B* 004* 1008CT-200-X*B* 005* 1008CT-300-X*B* 006* 1008CT-400-X*B* 007* 1008CT-500-X*B* 008* 1008CT-600-X*B* 009* 1008CT-700-X*B* 010* 1008CT-800-X*B* 011* 1008CT-900-X*B* 012* 1008CT-101-X*B* 1/ When “*“ is used for coded values, its the contractors responsibility to sele
21、ct those options allowed by the CID. 2/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. 7.6 Government users. To acquire i
22、nformation on obtaining these coils from the Government inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-CPAA, Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-7741. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Custodians: Navy - EC Preparing Activity: DLA - CC Project 5950-1064 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
