1、INCH-POUND AA59789/20 2 May 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .250 X .270 INCH (6.35 x 6.86 mm) BODY SIZE, WITH CAPTIVE REAR WEDGE AND VISUAL LOCK INDICATION, SCREW ACTUATED The General Services Admini
2、stration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). Th
3、is commercial item description (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES). AA59789 CID number /20 Applicable CID sheet * Configuration (see table I) * Finish (see table I) * * Length (see table II) * Mounting (see
4、 table I) Example: AA59789/20LE40T is the PIN for an electroless nickel finished, 3.8 inch (96.5 mm) long card holder. The card holder also features two tapped mounting holes for use with 080 UNF 2B fasteners and a screw selflocking element for added resistance to loosening. SALIENT CHARACTERISTICS.
5、 Performance. Card holders shall hold the circuit card firmly in place providing high resistance to shock and vibration while providing maximum thermal transfer. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein and meet the gen
6、eral requirements specified in CID AA59789. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “M“, “R“, “S“, “T“,
7、 and “U“. Cold plate slot width. The recommended cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installati
8、on torque is follows: 6 inch-pounds (0.7 N-m) for card holders of configuration “C“ or “E“ and 7 to 8 inch-pounds (0.8 to 0.9 N-m) for assemblies of configurations “L“ or “D“. Configuration. The configuration of a card holder shall be as specified in table I. The details of a particular configuratio
9、n consist of those on figures 1 and 2, and may include those on figures 3 and 4. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/20 2table I tables I TABLE I. Configurations. Configuration Applicable figures Hardware options
10、 C 1 and 2 No added options L 1, 2 and 3 Screw self-locking element E 1, 2 and 4 Additional mounting hole D 1, 2, 3 and 4 Screw self-locking element and additional mounting hole figure 1 figures 1 1 Inches mm Inches mm Inches mm Inches mm .227 .23 5.77 5.84 .250 .270 6.35 6.86 .325 .35 8.26 8.9 .80
11、20.32 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for information only. 2. Unless otherwise specified, tolerances are for .02 inch (0.51 mm) for two place decimals and .010 (0.25 mm) for three place decimals. 3. Tolerance for the hole spacing is .005 inch (0.13 mm). 4. The a
12、cross flats dimension for hex drive socket shall be .094 inch (2.38 mm). FIGURE 1. Relaxed and expanded dimensions. Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (chemical film), “E“ (e
13、lectroless nickel), or “H“ (hard black anodize). Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59789 and the lengths available for this CID specification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on f
14、igure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/20 3Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the card holder is in its relaxed (unlocked) state. When the card holder is in the unlo
15、cked (relaxed) state, the end of the actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened (assembly expanded) so that the assembly is in the locked position, this red band shall be concealed. FIGURE 2. Visual lock indicator
16、. table II TABLE II. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “length“ .02 (0.5 mm) Dimension “M“ .005 (0.13 mm) Dimension “M/2“ .005 (0.13mm) 30 2.80 (71.1) .90 (22.9) .45 (11.4) 40 3.80 (96.5) 1.90 (48.3) .95 (24.1) 50 4.80 (121.9) 2.90 (73.7) 1.45 (36.8) 1
17、/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Mounting. The mounting designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “M“ (tapped metric M2.5 x 0.45 holes), “R“ (rivet mount holes
18、with counterbore and countersink), “S“ (tapped 2-56 holes), “T“ (tapped 0-80 holes), or “U“ (tapped metric M2 x 0.4 holes). See figure 1 for mounting hole spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .068/.073 inch (1.73/1.85 mm) diameter, countersunk 100 de
19、grees by .060 inch (1.52 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59789 when rivet mounting is used. Configuration hardware options. Card holders can have the following options. See table I for the correct PIN configuration identifier. Screw self-locking element (see fi
20、gure 3). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock vibration. Card holders requiring a screw self-locking element shall include configuration identifier “L“ in the PIN (see table I). FIGURE 3. Screw self-locking element details. Pro
21、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/20 4Additional mounting hole (see figure 4). Card holders requiring an additional mounting hole shall include configuration identifier “E“ in the PIN (see table I). FIGURE 4. Additional mounting ho
22、le details. Screw self-locking element and additional mounting hole. Card holders requiring a screw self-locking element and an additional mounting hole options shall include configuration identifier “D“ in the PIN (see table I). NOTES. PIN. The PIN should be used for Government purposes to buy comm
23、ercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are av
24、ailable online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Other Publications AEROSPACE INDUSTRIES ASSOCIATION (AIA) AIA/NAS 1283 Fasteners, Male Threaded, Selfl
25、ocking. (Application for copies should be addressed to the Aerospace Industries Association, 1250 Eye Street, NW, Suite 1200, Washington, DC 200053924 or at URL: http:/www.aia-aerospace.org.) Ordering data. Ordering data is as specified in AA59789. Commercial products. As part of the market analysis
26、 and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID spe
27、cification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 5BG68 Card Locks Unlimited, Inc. 2310 E. Orange
28、thorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/20 5Part number supersession data. These CID specification sheet PINs supersedes the followin
29、g manufacturers part numbers as shown in table III and on DESC Drawing 89024 (table IV) as shown. The CID PINs listed in table III are only for length designator “50“. See table V for CID PIN construction using other available lengths for this CID specification sheet. This information is being provi
30、ded to assist in reducing proliferation in the Government inventory system. Table III table III III TABLE III. Commercial part number supersession data. PIN designator AA59789/20 Vendor similar designator or type part number 1/ CAGE 5BG68 PIN designator AA59789/20 Vendor similar designator or type p
31、art number 1/ CAGE 5BG68 CB50M 5260VBA-4.80TM2.5 EB50M 5260VBA-4.80ETM2.5 CB50R 5260VBA-4.80H EB50R S260VBA-4.80EH CB50S 5260VBA-4.80T2 EB50S 5260VBA-4.80ET2 CB50T 5260VBA-4.80T0 EB50T 5260VBA-4.80ET0CB50U 5260VBA-4.80TM2 EB50U 5260VBA-4.80ETM2 LB50M 5260VBA-4.80TM2.5L DB50M 5260VBA-4.80ETM2.5L LB50
32、R 5260VBA-4.80HL DB50R 5260VBA-4.80EHL LB50S 5260VBA-4.80T2L DB50S 5260VBA-4.80ET2L LB50T 5260VBA-4.80T0L DB50T 5260VBA-4.80ET0L LB50U 5260VBA-4.80TM2L DB50U 5260VBA-4.80ETM2L CC50M 5260VCG-4.80TM2.5 EC50M 5260VCG-4.80ETM2.5 CC50R 5260VCG-4.80H EC50R 5260VCG-4.80EH CC50S 5260VCG-4.80T2 EC50S 5260VCG
33、-4.80ET2 CC50T 5260VCG-4.80T0 EC50T 5260VCG-4.80ET0CC50U 5260VCG-4.80TM2 EC50U 5260VCG-4.80ETM2 LC50M 5260VCG-4.80TM2.5L DC50M 5260VCG-4.80ETM2.5L LC50R 5260VCG-4.80HL DC50R 5260VCG-4.80EHL LC50S 5260VCG-4.80T2L DC50S 5260VCG-4.80ET2L LC50T 5260VCG-4.80TOL DC50T 5260VCG-4.80ETOL LC50U 5260VCG-4.80TM
34、2L DC50U 5260VCG-4.80ETM2L CE50M 5260VEN-4.80TM2.5 EE50M 5260VEN-4.80ETM2.5 CE50R 5260VEN-4.80H EE50R 5260VEN-4.80EH CE50S 5260VEN-4.80T2 EE50S 5260VEN-4.80ET2 CE50T 5260VEN-4.80T0 EE50T 5260VEN-4.80ET0CE50U 5260VEN-4.80TM2 EE50U 5260VEN-4.80ETM2 See footnote at end of table. Provided by IHSNot for
35、ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/20 6TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/20 Vendor similar designator or type part number 1/ CAGE 5BG68 PIN designator AA59789/20 Vendor similar designator or type part
36、 number 1/ CAGE 5BG68 LE50M 5260VEN-4.80TM2.5L DE50M 5260VEN-4.80ETM2.5L LE50R 5260VEN-4.80HL DE50R 5260VEN-4.80EHL LE50S 5260VEN-4.80T2L DE50S 5260VEN-4.80ET2L LE50T 5260VEN-4.80T0L DE50T 5260VEN-4.80ET0L LE50U 5260VEN-4.80TM2L DE50U 5260VEN-4.80ETM2L CH50M 5260VBH-4.80TM2.5 EH50M 5260VBH-4.80ETM2.
37、5 CH50R 5260VBH-4.80H EH50R 5260VBH-4.80EH CH50S 5260VBH-4.80T2 EH50S 5260VBH-4.80ET2 CH50T 5260VBH-4.80T0 EH50T 5260VBH-4.80ET0CH50U 5260VBH-4.80TM2 EH50U 5260VBH-4.80ETM2 LH50M 5260VBH-4.80TM2.5L DH50M 5260VBH-4.80ETM2.5L LH50R 5260VBH-4.80HL DH50R 5260VBH-4.80EHL LH50S 5260VBH-4.80T2L DH50S 5260V
38、BH-4.80ET2L LH50T 5260VBH-4.80T0L DH50T 5260VBH-4.80ET0L LH50U 5260VBH-4.80TM2L DH50U 5260VBH-4.80ETM2L 1/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforemention
39、ed commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. table IV TABLE IV. DESC Drawing PIN supersession information. Superseded (old) PIN in accordance with DESC Drawing 89024 Superseding (new) CID
40、PIN Superseded (old) PIN in accordance with DESC Drawing 89024 Superseding (new) CID PIN 8902411BH AA59789/20CB30R 8902411CH AA59789/20CC30R 8902414BH AA59789/20CB40R 8902414CH AA59789/20CC40R 8902417BH AA59789/20CB50R 8902417CH AA59789/20CC50R 8902411BS AA59789/20CB30T 8902411CS AA59789/20CC30T 890
41、2414BS AA59789/20CB40T 8902414CS AA59789/20CC40T8902417BS AA59789/20CB50T 8902417CS AA59789/20CC50T 8902411BT AA59789/20CB30S 8902411CT AA59789/20CC30S 8902414BT AA59789/20CB40S 8902414CT AA59789/20CC40S 8902417BT AA59789/20CB50S 8902417CT AA59789/20CC50S Provided by IHSNot for ResaleNo reproduction
42、 or networking permitted without license from IHS-,-,-AA59789/20 7table V TABLE V. Example of PIN with available length designators. PIN designator AA59789/20 Vendor similar designator or type part number 1/ 2/ CAGE 5BG68 LE30T 5260VEN2.80T0L LE40T 5260VEN3.80T0L LE50T 5260VEN4.80T0L 1/ The manufact
43、urers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements,
44、see the marking paragraph in AA59789. 2/ Other lengths are available on request. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FSS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Project 59982008020 Review activity: Air Force 99 NOTE: The activities listed ab
45、ove were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
