1、 INCHPOUND AA59935/3 2 October 2013 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET CONICAL SEALS, CRUSH, 37 DEGREE FLARED TUBE FITTING, NICKEL The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procu
2、ring conical seal, crush, 37 degree flared tube fitting, nickel described herein shall consist of this document and the issue in effect of A-A-59935. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) uses a classification system which is included in the PIN a
3、s shown in the following example (see NOTES). AA59935/3 -04 N CID number Size code (see figure 1) Material and finish code (see table I) SALIENT CHARACTERISTICS. Interface and physical dimensions. Conical seals, crush, 37 degree flared tube fitting, nickel supplied to this CID specification sheet sh
4、all be as specified herein (see figure 1 and table I). Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432180-3990, or fluidflowdla.mil. Since
5、 contact information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil/. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/3 2 Dash size code T
6、ubing OD Ref. A +.005 -.000 B +.000 -.015 C +.005 -.000 D +.015 -.000 T inch -02 1/8 .240 .060 .245 .103 .005 -03 3/16 .302 .307 .166 -04 1/4 .354 .075 .359 .213 -05 5/16 .416 .421 .275 -06 3/8 .471 .476 .338 -08 1/2 .649 .095 .654 .446 .010 -10 5/8 .762 .105 .767 .562 -12 3/4 .933 .938 .687 -16 1 1
7、.183 .125 1.188 .936 -20 1-1/4 1.496 1.501 1.375 -24 1-1/2 1.745 1.750 1.410 -28 1-3/4 2.120 2.125 1.680 -32 2 2.370 2.375 1.913 -40 2 1/2 2.877 .055 2.882 2.500 .015 -44 2 3/4 3.127 3.125 2.742 -48 3 3.377 3.382 2.990 NOTES: 1. Dimensions are in inches. 2. Dimensioning and tolerancing in accordance
8、 with ASME Y14.5. Unless otherwise specified, tolerances for decimals .005 inch (0.13 mm), angles .5. 3. Break sharp edges and remove burrs and slivers. 4. Surface texture shall be .005 inches in accordance with ASME B46.1. 5. These parts are soft and easily deformed dimensions B, C, and D shall be
9、verified by installing the seal on a standard fitting of the appropriate size. 6. An out-of-round-seal that does not interfere with installation shall not be cause for rejection. FIGURE 1. 37 Flared crush seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
10、 IHS-,-,-A-A-59935/3 3 TABLE I. Material and finish code. Material and finish code Material and finish N Nickel strip 201, annealed, in accordance with ASTM B162 or SAE-AMS5553 NT Nickel strip 201, annealed, in accordance with ASTM B162 or SAE-AMS5553 Tin plated in accordance with ASTM B545 or SAE-A
11、MS2408 NS Nickel strip 201, annealed, in accordance with ASTM B162 or SAE-AMS5553 Silver plated in accordance with SAE-AMS2410 Tubing material and fluids or gases to be sealed, see table II. TABLE II. Tubing material and fluids or gases. Tubing and fitting material Assembly temperature range Fluids
12、or gases Steel -420F to +1500F (-251C to 816C) Hydraulic oil JP-4 JP-5 Liquid hydrogen Liquid Nitrogen Oxygen Pneumatics Water Torque technique. These seals require a second torque technique; see A-A-59935 for torqueing procedure. NOTES. PIN. The PIN should be used for Government purposes to buy com
13、mercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Other Publications COMMERCIAL ITEM DESCRIPTIONS A-A-59935 - Conical Seal, Crush, 37 Degree Flared Tube Fitting, General Requirements For (Copies of these documents are availa
14、ble online at http:/quicksearch.dla.mil/ or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/3 4 ASME INTERNATIONAL ASME Y14.5 - Dimensi
15、oning and Tolerancing ASME B46.1 - Surface Texture (Surface Roughness, Waviness, and Lay) (Copies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park Avenue, New York, NY 10016-5990.) ASTM INTERNATIONAL ASTM B162 - Standard Specification for Nicke
16、l Plate, Sheet, and Strip ASTM B545 - Standard Specification for Electrodeposited Coatings of Tin (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) SAE INTERNATIONAL SAE-AMS24
17、08 - Plating, Tin SAE-AMS2410 - Plating, Silver Nickel Strike, High Bake SAE-AMS5553 - Nickel, Sheet and Strip Low (0.02 max) Carbon Annealed - UNS N02201 (Copies of these documents are available on line at www.sae.org from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, and Te
18、l: 877-606-7323 inside USA and Canada or 724-776-4970 outside USA, email at CustomerServicesae.org.) Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID speci
19、fication sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only th
20、e manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/3 5 MFRs CAGE number MFRs name and address 33447 SECO Seals Inc. 1370 Logan Ave. Unit K Costa Mesa, CA 92626 714-546-3778 E-mail: 64162. Del Aerospace, Inc. 921 Mounta
21、in View Ave A Oxnard, CA 93030-7227 E-mail: 66776 Alcoa Global Fasteners Inc. Div Rosan / Eagle Products DBA Alcoa Fastening Systems 800 S State College Blvd Fullerton, CA 92831-5334 01673 SPS Technologies LLC DBA Airdrome Precision Components Div SPS Technologies LLC 3251 E Airport WY Long Beach,
22、CA 90806-2407 Part number (P/N) supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system (see table III). Provided by IHSNot for ResaleNo reproduction or
23、 networking permitted without license from IHS-,-,-A-A-59935/3 6 TABLE III. P/N supersession data. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02N 33447 SECO7N-02 64162 DY90-N-2 -03N 33447 SECO7N-03 64162 DY90-N-3 -04N 33447 SECO7N-04 64162 DY90-N-4 -05N 33447 SECO
24、7N-05 64162 DY90-N-5 -06N 33447 SECO7N-06 64162 DY90-N-6 -08N 33447 SECO7N-08 64162 DY90-N-8 -10N 33447 SECO7N-10 64162 DY90-N-10 -12N 33447 SECO7N-12 64162 DY90-N-12 -16N 33447 SECO7N-16 64162 DY90-N-16 -20N 33447 SECO7N-20 64162 DY90-N-20 -24N 33447 SECO7N-24 64162 DY90-N-24 -28N 33447 SECO7N-28 6
25、4162 DY90-N-28 -32N 33447 SECO7N-32 64162 DY90-N-32 -40N 33447 SECO7N-40 64162 DY90-N-40 -44N 33447 SECO7N-44 64162 DY90-N-44 -48N 33447 SECO7N-48 64162 DY90-N-48 Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02N 66776 VSF1015N2 01673 AP50A2 -03N 66776 VSF1015N3 0167
26、3 AP50*3 -04N 66776 VSF1015N4 01673 AP50*4 -05N 66776 VSF1015N5 01673 AP50*5 -06N 66776 VSF1015N6 01673 AP50*6 -08N 66776 VSF1015N8 01673 AP50*8 -10N 66776 VSF1015N10 01673 AP50*10 -12N 66776 VSF1015N12 01673 AP50*12 -16N 66776 VSF1015N16 01673 AP50*16 -20N 66776 VSF1015N20 01673 AP50*20 -24N 66776
27、VSF1015N24 01673 AP50*24 -28N 66776 VSF1015N28 01673 AP50*28 -32N 66776 VSF1015N32 01673 AP50*32 -40N 66776 VSF1015N40 01673 AP50*40 -44N 66776 VSF1015N44 01673 AP50*44 -48N 66776 VSF1015N48 01673 AP50*48 See note at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted
28、without license from IHS-,-,-A-A-59935/3 7 TABLE III. P/N supersession data - Continued. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02NT 33447 SECO7NT-02 64162 DY90-NT-2 -03NT 33447 SECO7NT-03 64162 DY90-NT-3 -04NT 33447 SECO7NT-04 64162 DY90-NT-4 -05NT 33447 SECO
29、7NT-05 64162 DY90-NT-5 -06NT 33447 SECO7NT-06 64162 DY90-NT-6 -08NT 33447 SECO7NT-08 64162 DY90-NT-8 -10NT 33447 SECO7NT-10 64162 DY90-NT-10 -12NT 33447 SECO7NT-12 64162 DY90-NT-12 -16NT 33447 SECO7NT-16 64162 DY90-NT-16 -20NT 33447 SECO7NT-20 64162 DY90-NT-20 -24NT 33447 SECO7NT-24 64162 DY90-NT-24
30、 -28NT 33447 SECO7NT-28 64162 DY90-NT-28 -32NT 33447 SECO7NT-32 64162 DY90-NT-32 -40NT 33447 SECO7NT-40 64162 DY90-NT-40 -44NT 33447 SECO7NT-44 64162 DY90-NT-44 -48NT 33447 SECO7NT-48 64162 DY90-NT-48 Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02NT 66776 VSF1015NT
31、2 01673 AP50A2 -03NT 66776 VSF1015NT3 01673 AP50*3 -04NT 66776 VSF1015NT4 01673 AP50*4 -05NT 66776 VSF1015NT5 01673 AP50*5 -06NT 66776 VSF1015NT6 01673 AP50*6 -08NT 66776 VSF1015NT8 01673 AP50*8 -10NT 66776 VSF1015NT10 01673 AP50*10 -12NT 66776 VSF1015NT12 01673 AP50*12 -16NT 66776 VSF1015NT16 01673
32、 AP50*16 -20NT 66776 VSF1015NT20 01673 AP50*20 -24NT 66776 VSF1015NT24 01673 AP50*24 -28NT 66776 VSF1015NT28 01673 AP50*28 -32NT 66776 VSF1015NT32 01673 AP50*32 -40NT 66776 VSF1015NT40 01673 AP50*40 -44NT 66776 VSF1015NT44 01673 AP50*44 -48NT 66776 VSF1015NT48 01673 AP50*48 See note at end of table.
33、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/3 8 TABLE III. P/N supersession data - Continued. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02NS 33447 SECO7NS-02 64162 DY90-NS-2 -03NS 33447 SECO7NS-03 6
34、4162 DY90-NS-3 -04NS 33447 SECO7NS-04 64162 DY90-NS-4 -05NS 33447 SECO7NS-05 64162 DY90-NS-5 -06NS 33447 SECO7NS-06 64162 DY90-NS-6 -08NS 33447 SECO7NS-08 64162 DY90-NS-8 -10NS 33447 SECO7NS-10 64162 DY90-NS-10 -12NS 33447 SECO7NS-12 64162 DY90-NS-12 -16NS 33447 SECO7NS-16 64162 DY90-NS-16 -20NS 334
35、47 SECO7NS-20 64162 DY90-NS-20 -24NS 33447 SECO7NS-24 64162 DY90-NS-24 -28NS 33447 SECO7NS-28 64162 DY90-NS-28 -32NS 33447 SECO7NS-32 64162 DY90-NS-32 -40NS 33447 SECO7NS-40 64162 DY90-NS-40 -44NS 33447 SECO7NS-44 64162 DY90-NS-44 -48NS 33447 SECO7NS-48 64162 DY90-NS-48 Dash number (see table I) AA5
36、9935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02NS 66776 VSF1015NS2 01673 AP50A2 -03NS 66776 VSF1015NS3 01673 AP50*3 -04NS 66776 VSF1015NS4 01673 AP50*4 -05NS 66776 VSF1015NS5 01673 AP50*5 -06NS 66776 VSF1015NS6 01673 AP50*6 -08NS 66776 VSF1015NS8 01673 AP50*8 -10NS 66776 VSF1015NS10 01673 AP50*
37、10 -12NS 66776 VSF1015NS12 01673 AP50*12 -16NS 66776 VSF1015NS16 01673 AP50*16 -20NS 66776 VSF1015NS20 01673 AP50*20 -24NS 66776 VSF1015NS24 01673 AP50*24 -28NS 66776 VSF1015NS28 01673 AP50*28 -32NS 66776 VSF1015NS32 01673 AP50*32 -40NS 66776 VSF1015NS40 01673 AP50*40 -44NS 66776 VSF1015NS44 01673 A
38、P50*44 -48NS 66776 VSF1015NS48 01673 AP50*48 1/ The manufacturers P/N shall not be used for procurement to the requirements of this specification sheet. At the time of preparation of this specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN s
39、hown. For actual part marking requirements, see the marking paragraph of A-A-59935. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/3 9 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FAS Army - AV Navy - AS Air Fo
40、rce - 99 Preparing activity: DLA - CC DLA - CC Review activities: Army - AT, MI Project 4730-2013-078 Navy - MC, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
