1、AN105501 THRU AN105600 REV 3 53 W 7777715 00002b5 7 K +.o00 -.o60 3.062 3.312 3.188 CSINK BTH ENDS HOLIS ON AXIS OF 60- TO ,100 DIA . PART AO. AN10591 AN105543 AN105542 L - 3% .500 .562 .625 .688 -750 .a12 * 875 .938 1,000 1.062 1.125 1.188 - 2.10 2.375 2.500 2.625 2.875 2.250 2.750 3.000 3.125 3.25
2、0 3.500 3.375 .1501 .OW 2.015 2.265 2.390 2.515 2. 65 2.140 2.640 2.&0 3.015 3.140 3.390 3.265 A - .265 .328 390 .452 -515 - 578 .640 ,702 .765 .828 .890 a952 1.015 1.078 - 1: +.o00 - .o60 8 Irl .125 .188 .250 .312 .375 .438 .500 ,562 .625 - THIS SWFACE MST BE SQMRE WITH S“K WITiiIR .O03 FULL IIIDIC
3、AT3 READIBO PART. HO. AN105506 AN105507 AN105508 AN105509 AN105s O AN105511 AN105512 AN105513 AN105514 AN105515 AN105517 AN105518 AN105519 Ai(i05516 t -CHAWE23 30aT0 .375 DU (OPPOSITE SIDE OpTIONLL) 1.250 1.140 1.312 1.202 1.375 1.265 X +.o00 - ,060 .688 :E . ti75 938 1.062 1.188 1.312 1.438 1.562 1
4、688 1.812 1.938 2.062 2.188 :G 2.562 2.688 2.812 2.938 - PART AO. Ml05520 AN105521 AN105522 AN105523 AN105524 AN105525 AN105527 AN105528 AN105519 AN105530 AN105531 AN 1 O 5 5 3 2 AN105533 AN105534 AN105535 AN105536 AN105537 U105538 AN1055 9 AN1055Z0 105526 L - 3.625 3.750 3.875 - A - 3.515 3.640 3
5、765 - THD WITHIN .005. ANGULAR LOCATION MAY VARY FREELY (a) THREAD TO HEAD. HAXIUUH TWO IHPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O04 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN ,006 FIR. (3) THE CONCENTRICITY OF THE SH
6、ANK IN RELATION TO THE WASHER FACE DIAHETER AND HEXAGON SHALL BE WITHIN .O11 FIR. INACTIVE FOR DESIGN AFTER 27 DEG i966 NO SUPERSEDING STANDARD. HATERIAL: CORROSION RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 HANUFACTURING SPECIFICATION: AHS 7472 BREAK SHARP EDGES .OD3
7、015 UNLESS OTHERWISE SPECIFIED. OIUEHSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES: LINEAR DIHENSIONS I.010. ANGULAR DO NOT USE UNASSIGNED PART NUHBERS. THrS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COHHITTEE OF THE SAE. 3 INSPECTION: ALL PARTS SHA
8、LL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE WITH AHS2645. DIHENSIONS t2. P.A. Ocher Cust USAF - II Navy - AS Army - AV I AIR FORCE-NAW AERONAUTICAL STANDARD BOLT - CRES HEX HEAD, DRILLED SHANK, .190-32 I AN IO5501 AN I8560 001- SimDC. 0.m.: III.111-IIUHII Project No. 5306-1039 / THIS DOCUMENT CONTAINS I PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
