1、ASME A112.19.3-2017/CSA B45.4-17Stainless steel plumbing fixturesLegal Notice for Harmonized Standard Jointly Developed by ASME and CSA GroupIntellectual property rights and ownershipAs between American Society of Mechanical Engineers (ASME) and Canadian Standards Association (Operating as “CSA Grou
2、p) (collectively ASME and CSA Group) and the users of this document (whether it be in printed or electronic form), ASME and CSA Group are the joint owners of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions an
3、d trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. The unauthorized use, modification, copying, or disclosure of this document may violate laws that protect the intellectual property of ASME
4、and CSA Group and may give rise to a right in ASME and CSA Group to seek legal redress for such use, modification, copying, or disclosure. ASME and CSA Group reserve all intellectual property rights in this document.Disclaimer and exclusion of liabilityThis document is provided without any represent
5、ations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. ASME an
6、d CSA Group do not warrant the accuracy, completeness, or currency of any of the information published in this document. ASME and CSA Group make no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation.IN NO EVENT SHALL ASME AND CSA GROUP,
7、 THEIR RESPECTIVE VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST
8、 REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF ASME OR CSA GROUP HAVE
9、BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, ASME and CSA Group are not undertaking to render professional or other services for or on behalf of any person or entity or to perform any duty owed by any person or en
10、tity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and ASME and CSA Group accept no responsibility whatsoever arising in any way from any and all use of or reliance on the information co
11、ntained in this document.ASME and CSA Group have no power, nor do they undertake, to enforce compliance with the contents of the standards or other documents they jointly publish.Authorized use of this documentThis document is being provided by ASME and CSA Group for informational and non-commercial
12、 use only. The user of this document is authorized to do only the following:If this document is in electronic form: load this document onto a computer for the sole purpose of reviewing it; search and browse this document; and print this document if it is in PDF format.Limited copies of this document
13、 in print or paper form may be distributed only to persons who are authorized by ASME and CSA Group to have such copies, and only if this Legal Notice appears on each such copy.In addition, users may not and may not permit others to alter this document in any way or remove this Legal Notice from the
14、 attached standard; sell this document without authorization from ASME and CSA Group ; or make an electronic copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document or make any copies of the contents hereof,
15、 and if you do make such copies, you are required to destroy them immediately. Use of this document constitutes your acceptance of the terms and conditions of this Legal Notice.Standards Update ServiceASME A112.19.3-2017/CSA B45.4-17March 2017Title: Stainless steel plumbing fixturesTo register for e
16、-mail notification about any updates to this publication go to shop.csa.ca click on CSA Update ServiceThe List ID that you will need to register for updates to this publication is 2425142.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on
17、 privacy at www.csagroup.org/legal to find out how we protect your personal information.ASME/CSA StandardASME A112.19.3-2017/CSA B45.4-17 Stainless steel plumbing fixturesA trademark of the Canadian Standards Association and CSA America Inc., operating as “CSA Group”CSA Group A not-for-profit privat
18、e sector organization178 Rexdale Boulevard, Toronto, Ontario, Canada M9W 1R3 1-800-463-6727 416-747-4044Visit the CSA Group Online Store at shop.csa.caThe American Society of Mechanical Engineers (ASME) Three Park AvenueNew York, NY 10016-5990, USA1-800-843-2763Visit the ASME Online Store at www.asm
19、e.orgCommitment for AmendmentsThis Standard is issued jointly by the American Society of Mechanical Engineers (ASME) and the Canadian Standards Association (Operating as “CSA Group”). Amendments to this Standard will be made only after processing according to the Standards writing procedures of both
20、 ASME and CSA Group. The American Society of Mechanical Engineers (ASME) Three Park Avenue New York, NY 10016-5990 USA 1-800-843-2763 Visit the ASME Online Store at www.asme.orgPublished in February 2017 by CSA Group A not-for-profit private sector organization 178 Rexdale Boulevard Toronto, Ontario
21、, Canada M9W 1R3 1-800-463-6727 or 416-747-4044 Visit the CSA Group Online Store at shop.csa.caCopyright 2017 by The American Society of Mechanical Engineers (ASME)ISBN 978-1-4883-0739-3 CSA Group 2017The 2017 edition of this Standard is being issued with an automatic addenda subscription service. T
22、he use of addenda allows revisions made in response to public review comments or committee actions to be published as necessary.All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher.ASME A112.19.3-2017/CSA B45.4-17 Sta
23、inless steel plumbing fixturesMarch 2017 The American Society of Mechanical Engineers 2017 CSA Group1ContentsASME A112 Standards Committee on Plumbing Materials and Equipment 3ASME A112.19.3 Project Team on Stainless Steel Plumbing Fixtures 7CSA Technical Committee on Plumbing Fixtures 9CSA/ASME Har
24、monization Task Group on Plumbing Fixtures 14Preface 161 Scope 182 Reference publications 193 Definitions 194 General requirements 214.1 Materials 214.2 Stainless steel thickness 214.2.1 Lavatories and sinks 214.2.2 Other fixtures 214.3 Tolerances 214.4 Waste fitting openings, drainage, and overflow
25、s 224.4.1 Waste fitting openings and drainage 224.4.2 Overflows 224.5 Additional requirements for water closets 224.6 Additional requirements for urinals 234.7 Additional requirements for lavatories, sinks, and bidets 234.7.1 Openings and mounting surfaces for supply fittings 234.7.2 Laundry or util
26、ity sink capacity 234.8 Additional requirements for bathtubs and shower bases 234.8.1 Minimum dimensions for bathtubs 234.8.2 Slope to the waste outlet 234.8.3 Flanges 234.9 Additional requirements for drinking fountains 244.10 Accessible design fixtures 245 Tests 245.1 Surface examination 245.1.1 P
27、rocedure 245.1.2 Performance 245.2 Warpage test 245.2.1 Procedure 245.2.2 Performance 255.3 Field-installed flange test 255.3.1 Procedure 255.3.2 Performance 25ASME A112.19.3-2017/CSA B45.4-17 Stainless steel plumbing fixturesMarch 2017 The American Society of Mechanical Engineers 2017 CSA Group25.4
28、 Overflow test (lavatories, sinks, and bidets) 255.4.1 Procedure 255.4.2 Performance 255.5 Structural integrity tests 265.5.1 Water closets 265.5.2 Lavatories and sinks 265.5.3 Wall-mounted urinals 275.5.4 Bathtubs and shower bases 276 Markings, packaging, and installation instructions and other lit
29、erature 286.1 General 286.2 Non-standard fixtures 296.3 Additional markings for water closets and urinals 296.4 Field-installed flanges 296.5 Packaging and installation instructions and other literature 296.5.1 General 296.5.2 Packaging 296.5.3 Installation instructions 30Annex A (informative) Unit
30、conversion criteria 36ASME A112.19.3-2017/CSA B45.4-17 Stainless steel plumbing fixturesMarch 2017 The American Society of Mechanical Engineers 2017 CSA Group3ASME A112 Standards Committee on Plumbing Materials and EquipmentW.M. Smith American Society of Plumbing Engineers, Montgomery, Alabama, USA
31、ChairS.M. Rawalpindiwala Kohler Co. Plumbing Division, Kohler, Wisconsin, USA Vice-ChairC. McLeod Kohler, Dana Point, California, USA Alternate to: S. RawalpindiwalaAlternateR.K. Adler City of San Jose, San Jose, California, USA J.A. Ballanco JB Engineering however, they should not contain proprieta
32、ry names or information.ASME A112.19.3-2017/CSA B45.4-17 Stainless steel plumbing fixturesMarch 2017 The American Society of Mechanical Engineers 2017 CSA Group17ASME procedures provide for reconsideration of any interpretation when or if additional information that might affect an interpretation is
33、 available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME Committee.Interpretations are published on the ASME Web site under the Committee Pages at http:/www. asme.org/codes/ as they are issued.CSA Notes:1) Use of the singular does not exclude the plural (and vice
34、versa) when the sense allows.2) Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose.3) This publication was developed by consen
35、sus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a member may be included in the Technical
36、Committee list and yet not be in full agreement with all clauses of this publication.4) To submit a request for interpretation of CSA Standards, please send the following information to inquiriescsa.ca and include “Request for interpretation” in the subject line: a) define the problem, making refere
37、nce to the specific clause, and, where appropriate, include an illustrative sketch;b) provide an explanation of circumstances surrounding the actual field condition; andc) where possible, phrase the request in such a way that a specific “yes” or “no” answer will address the issue. Committee interpre
38、tations are processed in accordance with the CSA Directives and guidelines governing standardization and are published in CSAs periodical Info Update, which is available on the CSA website at http:/standardsactivities.csa.ca.5) CSA Standards are subject to periodic review, and suggestions for their
39、improvement will be referred to the appropriate committee. To submit a proposal for change to CSA Standards, please send the following information to inquiriescsa.ca and include “Proposal for change” in the subject line: a) Standard designation (number);b) relevant clause, table, and/or figure numbe
40、r;c) wording of the proposed change; andd) rationale for the change.6) Attention is drawn to the possibility that some of the elements of this Standard may be the subject of patent rights. CSA is not to be held responsible for identifying any or all such patent rights. Users of this Standard are exp
41、ressly advised that determination of the validity of any such patent rights is entirely their own responsibility.ASME A112.19.3-2017/CSA B45.4-17 Stainless steel plumbing fixturesMarch 2017 The American Society of Mechanical Engineers 2017 CSA Group18ASME A112.19.3-2017/CSA B45.4-17Stainless steel p
42、lumbing fixtures1 Scope1.1 This Standard covers plumbing fixtures made of stainless steel alloys and specifies requirements for materials, construction, performance, testing, and markings.Note: The term “corrosion-resisting steel” is also applied to stainless steel.1.2 This Standard covers the follo
43、wing plumbing fixtures:a) bathtubs;b) bidets;c) drinking fountains and water coolers;d) lavatories;e) shower bases;f) sinks: i) kitchen and bar sinks;ii) laboratory sinks;iii) laundry sinks;iv) service sinks; andv) utility sinks;vi) urinals; andvii) water closets.1.3 In this Standard, “shall” is use
44、d to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the
45、 Standard.Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.Notes to tables and figures are considered part of the table or figure and may be written as requ
46、irements.Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.1.4 SI units are the units of record in Canada. In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application
47、; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.ASME A112.19.3-2017/CSA B45.4-17 Stainless steel plumbing fixturesMarch 2017 The American Society of Mechanical Engineers 2017 CSA Group19All referen
48、ces to gallons are to U.S. gallons.For information on the unit conversion criteria used in this Standard, see Annex A.2 Reference publicationsThis Standard refers to the following publications, and where such reference is made, it shall be to the edition listed below, including all amendments publis
49、hed thereto.CSA GroupB125.3-12 Plumbing fittingsB651-12 Accessible design for the built environmentC22.2 No. 0.15-15 Adhesive labelsASME (American Society of Mechanical Engineers)/CSA GroupASME A112.18.1-2012/CSA B125.1-12 Plumbing supply fittingsASME A112.18.2-2015/CSA B125.2-15 Plumbing waste fittingsASME A112.19.2-2013/CSA B45.1-13 Ceramic plumbing fixturesASTM International (American Society for Testing and Materials)A240/A240M-16 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and
