1、I - - AN106701 THRU AN107000 REV 3 53 = 9777715 O000277 7 9 o FED. SUP CLASS. 5306 MATERIAL IDENTIFICATION PER AM.52800. RAISED OR DEPRESSED .O10 MAX K TO FULL T CHAMFlE .O47 x 45 APPROX .O16 OR CHAW - k SECTION TIIRU THREAD PROFILE .500-2(UW-3A SPEC UIL-s-7742 THIS SURFACE MUST BE SQUARE WITH SHAM
2、WITIIIN .O03 PULL INDICATOR READING CSINK 90 TO DIA BOTH EM -CHAMFER 30. TO -750 DIA (OPPOSITE SIDE OPTIONAL) L 1.000 1.062 1.125 1.188 1.250 1.312 1 - 375 1.438 1.500 1.562 1.625 1.688 1.750 1.812 ,562 AN106919 AN106907 1.938 .688 AN10691 AN106906 1-.875 .625 106920 AN106908 2.000 .750 106922 AN106
3、909 2.062 -812 AN106923 AN106910 2.125 .875 AN106924 AN106911 2 a 188 .938 AN10695 Arfio6912 2.250 1.000 AN106926 .1 8 AN106913 2.375 1.125 AN106927 :250 AN106914 2.500 1.250 AN106928 .312 AN106915 2.625 1.375 AN106929 .375 16916 2.750 1.500 AN106930 .438 106917 2.875 1.625 AN106931 .500 1 AN106918
4、1) 3.000 I 1.750 I AN106932 +. O00 3.125 1.875 3.250 2,000 3.375 2.125 3.500 2.250 3.750 2.500 3625 2.375 3.875 2.625 4.000 2. 50 4.125 2.875 4.250 3.000 4.375 3.125 4.500 3.250 PNIT NO. AN106933 AN106934 ANlCJ6935 AN106936 AN106538 AN136939 ANlu6940 AN106941 AN106942 AN106943 AN106944 AN106945 AN10
5、6946 10697 L K PART NC +.ooo. - .o60 4.875 3.625 AN10694. 5.000 3.750 AN10691 5.125 3.875 AN10694! 5.250 4.000 AN10695i 5.375 4.125 ANi0695: 5.500 4,250 AN10695: 5. 5.875 50 4.500 4.625 AN106955 AN106954 6.000 4.750 A1069S 5.625 4.375 ANlo695: (a) THREAD TO HEAD. HAXIHUH TWO IHPERFECT THREADS. NOTE:
6、 (I) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRrCITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF T9E SHANK IN RELATION TO THE WASHER FACE DIAHETER AND HEXAGON SHALL BE WITHIN ,023 FIR. INACTIVE FOR DESIGN AFTER 27 D
7、EC 1966 NO SUPERSEDJNG STANDARD. HATERIAL: CORROSON RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 HANUFACTURING SPECIFICATION: AUS 7472 BREAK SHARP EDGES .003-.015 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECLFTED: TOLERANCES; LINEAR DIMENSIONS
8、 t.010, ANGULAR 9 INSPECTION: ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE WITH AMS2645. DIHENSIONC 22. DO NOT USE UNASSIGNED PART NUMBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE ANO PROPELLER UTILITY PARTS COMHITTEE OF THE SAE. P.A. Other Cust AIR FORCE-
9、NAVY AERONAUTICAL STANDARD BOLT - CRES HEX HEAD .500-20 AN I0690 I AN I b”7000 USAF - II Navy - AS Army - AV I I Project No. 5306-105 .u .- s- 0I-L islr.i,i.riY,iii THI& DOCUMENT CONTAINS 1- - PAGES. r Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
