1、 ANLOBOOL THRU ANLOBLOO REV 3 53 m 7797935 O000290 8 m FED. SUP CLASS 5306 HATERIAL IDENTIFICATION AHS 2800 RAISED OR DEPRESSED .O10 HAX DRILL .I88 TO “ DEPTH SHOWN .I90 TO POINT .O16 OR CHAHFER IHPERFECT SECTION THRU THREAD PROFILE THIS SURFACE MUST BE SQUARE WITH SHANK WITHIN .O03 FULL INDICATOR
2、N0.50(.070) CSINK 90 TO +.o00 -.O60 .375 .625 (a) .688 1 .I88 .750 .250 2: I : .IO0 DIA 6 HOLES SPACED AS SHOWN WITHIN .O20 OF TRUE POSITION PART NO AN108006 AN108007 AN108008 AN108009 AN 1080 1 O ANI0801 1 AN108012 AN108013 AN 1080 14 AN 108015 AN1080 16 L I. 938 2.000 2.062 2.125 2,188 2,250 2.312
3、 2.375 2.438 2.500 2.625 2.750 2.875 3.000 K +.ooc -.Oh( - .438 .500 .562 .625 ,688 .750 ,812 .875 .938 1 .o00 1.125 1.250 1.375 1.500. PART NO AN 1080 17 AN 1080 18 AN 1 O80 19 AN108020 AN108021 AN108022 AN 108023 AN 1 ORO 24 AN108025 AN108026 AN108027 AN108028 AN LO802 9 AN108030 L - 3.L25 3.250 3
4、375 3.500 3.625 3.750 3.875 4. DOO 4.125 4,250 4.375 4.500 4.625 4.750 +.O00 PART NO. -. O60 1.625 AN108031 1.750 AN108032 1.875 AN108033 2.000 AN108034 2.125 AN108035 + 2.250 AN108036 2.375 AN108037 2.500 AH108038 2.625 AN108039 2.750 AN108040 2.875 AN108041 3.000 AN108042 L I +.:o0 -. 060 5.250 3
5、750 5.375 3.875 5.500 4.000 5.625 4.125 5.750 4.250 5.875 4.375 6.000 4.500 L PARI NO. AN108045 AN I08046 AN108047 AN 108048, AN108049 AN108050 AN108051 AN 1 O8 O 5 2 AN1 0805 3 AN108054 (a) THREAD TO HEAD. HAXIHUH TWO IHPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH O
6、F BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASIIER FACE DIAMETER ANO HEXAGON SHALL BE WITHIN .O28 FIR-. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. HATERIAL: CORROSION R
7、ESISTANT STEEL - SEE HANUPACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 HANUFACTURING SPECIFICATION: AUS 7472 INSPECTION: ALL PARTS SNALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE YITH AHS2645. BREAK SHARP EDGES .O03 - .O15 UNLESS OTHERWISE SPECIFIED. DIKENSIONS IN INCNES. UNLESS OTHE
8、RWISE SPECIFIED: DIHENSIONS t2 TOLERANCES: LINEAR DIHENSIONS f.010. ANGULAR DO NOT USE UNASSIGNED PART NUMBERS. THIS STANDARD YAS DEVELOPED COOPERATIVELY YITH THE ENGINE AND PROPELLER UTILITY PARTS COHHITTEE OF THE SAE. AN I0800 I P.A. USAF - II Other Cust AIR FORCE-NAVY AERONAUTICAL STANDARD ANIBIW Navy - AS BOLT - CRBS DRILLED HEX HEAD, 6 HOLES, .625-18 Army - AV I I oI-oIIEL ImQI4IumI* Project No. 5306-1064 / THIS DOCUMENT CONTAINS -h- .- PAGE. I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
