1、AMSC N/A FSC 5340 AN665 REV 6 31 August 2011 SUPERSEDING AN665 REV 5 8 APRIL 2009 DETAIL SPECIFICATION SHEET TERMINAL THREADED CLEVIS TYPE TIE ROD This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product des
2、cribed herein shall consist of this specification sheet and procurement specification MIL-DTL-5683. FIGURE I. Tie Rod. INCH-POUND Inactive for new design after 4 April 1998. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AN665 REV 6 2 TABLE I. Dash
3、numbers and dimensions. Dash No. Rated tie rod strength MIN (LB) Tap T Drill A B .015 D +.003 -.000 F +.010 -.005 G +.010 -.000 H I +.010 -.000 M +.010 -.000 S U Y .047 Z 10L 10R 1200 6-40 .147 1.313 .190 +.002 -.000 .250 .109 .375 .031 .250 .375 .625 .250 .313 21L 21R 2400 10-32 .199 1.531 .313 .15
4、0 .469 .281 .500 .719 .313 .375 34L 34R 4200 1/4-28 .261 1.813 .250 .438 .625 .047 .375 .625 .875 .438 .500 46L 46R 4600 (3) 5/16-24 .323 1.875 .313 .500 .203 .656 .438 .688 .938 .563 .625 61L 61R 6900 2.000 .563 .844 .453 .750 1.000 80L 80R 10000 3/8-24 .386 2.250 .375 .266 .875 .063 .547 .875 1.12
5、5 .688 .750 80LA 80RA .625 115L 115R 13700 7/16-20 .453 2.500 .438 .719 .344 1.000 .078 .625 1.063 1.250 .750 .813 155L 155R 18500 1/2-20 .516 2.813 .500 .813 .406 1.188 .703 1.188 1.438 .875 .938 202L 202R 24000 9/16-18 .578 3.125 .563 .922 .453 1.375 .094 .796 1.375 1.625 1.000 1.063 247L 247R 295
6、00 5/8-18 .640 3.375 .625 1.032 .516 1.500 .875 1.500 1.750 1.125 1.188 430L 430R 42000 3/4-16 .766 4.125 .750 1.250 .656 1.938 .109 1.063 1.813 2.250 1.375 1.438 580L 580R 58000 7/8-14 .891 4.875 .875 1.500 .781 2.313 1.250 2.125 2.688 1.625 1.688 760L 760R 76000 1-14 1.016 5.750 1.000 1.750 .906 2
7、688 .125 1.438 2.438 3.125 1.875 1.938 780L 780R 76000 1-12 1.016 5.750 1.000 1.750 .906 2.688 .125 1.438 2.438 3.125 1.875 1.938 Notes: 1. Material: Steel in accordance with procurement specification, MIL-DTL-5683. 2. Dimensions in inches. Unless otherwise specified, tolerances: Dimensions .010, A
8、ngles 3. 3. Special, for use with 6900 lb. rod with 4600 lb. rating. 4. Remove all burrs and sharp edges. 5. Example of part number: AN665-10L - left hand thread AN665-10R - right hand thread 6. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate
9、 where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespecti
10、ve of the marginal notations and relationship to the last previous issue. Custodians: Preparing Activity: Army - MI DLA -IS Navy - AS Air Force - 99 (Project 5340-2011-003) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
