1、 NOTICE OF REVISION (NOR) This revision described below has been authorized for the document listed. 1. DATE (YYMMDD) 25 August 2006 Form Approved OMB No. 0704-0188 Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions
2、, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department
3、of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. PLEASE DO NOT RETURN YOUR C
4、OMPLETED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMENT ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM.2. PROCURING ACTIVITY NO. 3. DODAAC 4. ORIGINATOR b. ADDRESS (Street, City, State, Zip Code)Defense Supply Center
5、Columbus 3990 East Broad Street Columbus, Ohio 43218-3990 5. CAGE CODE037Z3 6. NOR NO.5935-R042-003 a. TYPED NAME (First, Middle Initial, Last) Ron Gary 7. CAGE CODE037Z3 8. DOCUMENT NO.04026 9. TITLE OF DOCUMENT Connector, Concentric Twinaxial, Radio Frequency, (Threaded Receptacle, Socket Contact)
6、 Jamnut Mounted, Solder Pocket, Series DBA 10. REVISION LETTER 11. ECP NO.N/A a. CURRENTb. NEWA 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIESALL 13. DESCRIPTION OF REVISIONSheet 1: Revisions Ltr. Column; add “A” Revisions rev status of pages, blocks 1 and 6, add “A”. Revisions rev status o
7、f sheet 1, add “A”. Sheet 6: Revisions rev status of sheet, add “A”. Sheet 6: Delete and substitute the following: “ DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 14949 BJ 3150 04026ZBN-2 91836 2804-2-9 “ 14. THIS SECTION FOR GOVERNMENT USE ONLY a. (X one) X (1) Existing document suppl
8、emented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Custodian of master document shall make above revision and furnish revised document. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENTDSCC-VAI c. TYPED NAME
9、 (First, Middle Initial, Last)Richard L. Taylor d. TITLECHIEF, INTERCONNECTION DEVICES e. SIGNATURERichard L. Taylor f. DATE SIGNED (YYMMDD) 25 August 2006 15a. ACTIVITY ACCOMPLISHING REVISIONDSCC-VAI b. REVISION COMPLETED (Signature)Ron Gary c. DATE SIGNED (YYMMDD) 25 August 2006 DD Form 1695, APR
10、92 Previous editions are obsolete Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-REVISIONS LTR DESCRIPTION DATE APPROVED Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAG
11、E 1 2 3 4 5 6 PREPARED BY PMIC G Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS P.O. BOX 3990, COLUMBUS, OHIO 43218-3990 CHECKED BY Mary McWilliams APPROVED BY Richard Taylor TITLE CONNECTOR, CONCENTRIC TWINAXIAL, RADIO FREQUENCY, (THREADED RECEPTACLE, SOCKET CONTACT) JAMNUT MOUNTED, SOLDER POCKET, SERIES
12、 DBA SIZE CAGE CODE 037Z3 DWG. NO. 04026 Original date of drawing 22 May 2006 A REV PAGE 1 OF 6 AMSC N/A 5935-E750 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FIGURE 1. General configuration. SIZE CAGE CODE DWG NO. 037Z3 04026 DEFENSE SUPPLY CENT
13、ER, COLUMBUS P.O. BOX 3990, COLUMBUS, OHIO 43218-3990 A REVPAGE2 Part or Identifying Number (PIN) 04026ZB*-1 Inches mm Inches mm .020 0.51 .187 4.75 .027 0.68 .317 8.05 .034 0.86 .321 8.15 .039 0.99 .375 9.52 .093 2.36 .393 9.98 .094 2.39 .437 11.10 .128 3.25 .480 12.20 .131 3.33 .780 19.81 .148 3.7
14、6 1.0550 26.67 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Wrench flats ar
15、e to accommodate standard wrench openings in accordance with FED-STD-H28. 5. Interface shall be in accordance with MIL-STD-348, series DBA, socket contact. 6. Maximum panel thickness .187 inch (4.75 mm). 7. Orientation from the flat to the solder pocket shall be as shown. FIGURE 1. General configura
16、tion - Continued. SIZE CAGE CODE DWG NO. 037Z3 04026 DEFENSE SUPPLY CENTER, COLUMBUS P.O. BOX 3990, COLUMBUS, OHIO 43218-3990 A REVPAGE3 PIN 04026ZB*-2 Inches mm Inches mm .022 0.56 .562 14.27 .034 0.86 .615 15.62 .087 2.21 .740 18.79 .096 2.44 1.080 27.43 .187 4.75 .190 4.83 .439 11.15 .443 11.25 .
17、547 13.89 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MATERIALS: Connector body, hex nut, clamp nut and cone: Brass in accordance with ASTM B16/B16M, ASTM B36/B36M or ASTM B121/B121M. Nickel plated, 50 microinches (1.27 mm), minimum, in accordanc
18、e with SAE-AMS-QQ-N-290, class 1 or Silver plated in accordance with MIL-PRF-49142. Center contact: Beryllium copper in accordance with ASTM B194, ASTM B196/B196M or ASTM B197/B197M. Gold plated a minimum thickness of 50 microinches (1.27 mm) in accordance with ASTM B488, type II, code C, class 1.27
19、, over 50 microinches (1.27 mm) of nickel in accordance with SAE-AMS-QQ-N-290, class 1. Intermediate contact: Brass in accordance with ASTM B16/B16M, ASTM B36/B36M or ASTM B121/B121M. Gold plated a minimum thickness of 50 microinches (1.27 mm) in accordance with ASTM B488, type II, code C, class 1.2
20、7, over 50 microinches (1.27 mm) of nickel in accordance with SAE-AMS-QQ-N-290, class 1. Crimp sleeve: Brass in accordance with ASTM B16/B16M, ASTM B36/B36M or ASTM B121/B121. Nickel plated 50 microinches (1.27 mm), minimum, in accordance with SAE-AMS-QQ-N-290, class 1. Insulators and dielectrics: P
21、TFE in accordance with ASTM D1710 or ASTM D4895, or FEP in accordance with ASTM D2116. Lock washer: Phosphor Bronze in accordance with CDA 425, C42500, ASTM B591 and ASTM B888 or equivalent. Sealing gasket: Silicone rubber in accordance with A-A-59588. ENGINEERING DATA: (Metric equivalents are in pa
22、rentheses and given for general information only) Nominal impedance: Non-constant. Frequency range: 0 to 500 MHz. Voltage rating: 400 V rms at sea level, maximum. 100 V rms at 70,000 feet (4.437 kPa), maximum. Temperature rating: -65C to +200C. REQUIREMENTS: Requirements of drawing 84148 is applicab
23、le. Dimensions and configuration: See figures 1 and MIL-STD-348. Force to engage and disengage: Longitudinal force: 4 pounds (17.8 N), maximum. Torque: 2.5 inch-pounds (0.28 Nm), maximum. Mating characteristics: All test pins steel, with 16 microinches (0.405 m) finish. Center contact (socket); Over
24、size test pin: .0190 +.0001 inch (0.48 + 0.002 mm) diameter. Insertion depth: .030 to .045 inch (0.76 to 1.14 mm). Number of insertions - 1 Insertion force test: Test pin diameter : .0185 +.0001 inch (0.47 +0.002 mm). Insertion depth: .050 to .075 inch (1.27 to 1.90 mm) Insertion force: 1 pound (4.4
25、 N), maximum. SIZE CAGE CODE DWG NO. 037Z3 04026 DEFENSE SUPPLY CENTER, COLUMBUS P.O. BOX 3990, COLUMBUS, OHIO 43218-3990 A REVPAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Withdrawal force test: Test pin diameter: .0170 -.0001 inch (0.43 0.0
26、02 mm). Insertion depth: .100 to .125 inch (2.54 to 3.17 mm). Withdrawal force: 0.5 ounces (0.14 N), minimum. Coupling proof torque - Not applicable. Permeability of non-magnetic materials: In accordance with ASTM A342/A342M. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not appli
27、cable. Insulation resistance: In accordance with MIL-PRF-49142, 5,000 megohms. Points of measurement: 1. Between center conductor and intermediate conductor. 2. Between intermediate conductor and outer conductor. Center contact retention: Axial force: 2 pounds (8.9 N), minimum. Moisture resistance:
28、In accordance with MIL-PRF-49142. Contact resistance (in milliohms, maximum): Initial After environment Center contact: 6.0 8.0 Intermediate contact 3.0 5.0 Outer contact: 1.0 3.0 Dielectric withstanding voltage at sea level: In accordance with MIL-PRF-49142. At sea level, 750 V rms, measured betwee
29、n center and intermediate contact. 350 V rms, measured between intermediate contact and outer contact. Thermal shock: In accordance with MIL-PRF-49142. Except high temperature shall be +200C when using +200C cables. Salt spray: In accordance with MIL-PRF-49142. Vibration: In accordance with MIL-PRF-
30、49142. Shock (specified pulse): In accordance with MIL-PRF-49142. Corona: In accordance with MIL-PRF-49142. Altitude: 70,000 feet (4.437 kPa). Voltage: 125 V rms, minimum. RF high potential withstanding voltage: In accordance with MIL-PRF-49142. Test frequency: 5 to 7.5 MHz 500 V rms, between center
31、 contact and intermediate contact. 125 V rms, between intermediate contact and outer contact. Risetime degradation: 800 picoseconds, maximum. Cable retention force: Not applicable. SIZE CAGE CODE DWG NO. 037Z3 04026 DEFENSE SUPPLY CENTER, COLUMBUS P.O. BOX 3990, COLUMBUS, OHIO 43218-3990 A REVPAGE5
32、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Connector durability: 500 cycles minimum, at 12 cycles per minute maximum. Connectors must meet force to engage and disengage after cycling. Coupling mechanism retention force: Not applicable. PIN: 0402
33、6ZB*-1 and 04026ZB*-2 Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE nu
34、mber Vendor reference PIN 04026ZBN-2 14949 BJ 3150 04026ZBS-2 91836 2804-2-9 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor Name and Number address14949 Trompeter Electronics 5550 E. McDowell Rd. Mesa, Arizona 85215 91836 Kings Electronics 1685 Overview Dr. SIZE CAGE CODE DWG NO. 037Z3 04026 DEFENSE SUPPLY CENTER, COLUMBUS P.O. BOX 3990, COLUMBUS, OHIO 43218-3990 A REVPAGE6 Rock Hill, SC 29730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
