1、REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Jesus V. Garcia III DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 Original date of drawing 17 December 2009 CHECKED BY
2、Andrew R. Ernst TITLE RESISTOR NETWORK, FIXED FILM, 10 PAD, BALL GRID ARRAY APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09013 REV PAGE 1 OF 8 AMSC N/A 5905-E710 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CE
3、NTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09013 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a fixed, film, resistor network with 10 pad ball grid array. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 09013 - * * * Drawing
4、number Resistance value designator (see 3.3.1) Resistance tolerance (see 3.3.3) Schematic (see 3.3.6) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handbooks form a part of this document to the extent specified herei
5、n. Unless otherwise specified, the issues of these documents are those listed in the cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Specificat
6、ion for. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict bet
7、ween the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirem
8、ents shall be in accordance with MIL-PRF-55342 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-55342 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted w
9、ithout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09013 REV PAGE 3 mm Inch mm Inch mm Inch mm Inch 0.100 0.004 0.350 0.014 0.640 0.025 1.200 0.047 0.270 0.010 0.380 0.015 0.650 0.026 3.200 0.126 NOTES: 1. Dimensions are in Metric. Inches e
10、quivalents are given for general information only. 2. The pictorial view of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable
11、. 3. The bottom view shown above represents the mounting side. FIGURE 1. Resistor network. 3.3 Electrical characteristics 3.3.1 Resistance. The four-digit resistance designation is applicable to all resistance tolerances. The nominal resistance is identified by four digits; the first three digits re
12、present significant figures and the last digit specifies the number of zeros to follow. When the value of resistance is less than 100 ohms, or when a fractional value of an ohm is required, the “R” will be substituted for one of the significant digits to represent the decimal point. When the letter
13、“R” is used, succeeding digits of the group represent significant figures. The resistance values designations are shown in table I. Standard values for every decade will follow the sequence demonstrated for “10 to 100” decade in table II. Resistance values not listed in table II for the appropriate
14、resistance tolerance will be considered as not conforming to the specification. TABLE I. Designation of resistance values for resistance Designation Resistance ohms 10R0 to 98R8 incl. 10.0 to 98.8 incl. 1000 to 9880 incl. 100 to 988 Incl. 1001 to 9881 incl. 1,000 to 9,880 incl. 1002 incl. 10,000 inc
15、l. 3.2 mm 0.1 mm B A 0.27 mm 0.1 mm 1 2 3 4 5.65 mm 0.65 mm 1.2 mm 0.1 mm 0.38 mm 0.1 mm 0.1 mm 0.64 mm 0.35 mm diameter solder bump Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO.
16、037Z3 DWG NO. 09013 REV PAGE 4 TABLE II. Standard resistance values for the 10 to 100 decade. 1/ (B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J) 10.00 10.00 10.00 18.40 33.20 33.20 58.30 10.10 18.70 18.70 33.60 59.00 59.00 10.20 10.20 18.90 34.00 3
17、4.00 59.70 10.40 19.10 19.10 34.40 60.40 60.40 10.50 10.50 19.30 34.80 34.80 61.20 10.60 19.60 19.60 35.20 61.90 61.90 10.70 10.70 19.80 35.70 35.70 62.00 10.90 20.00 20.00 20.00 36.00 62.60 11.00 11.00 20.30 36.10 63.40 63.40 11.10 20.50 20.50 36.50 36.50 64.20 11.30 11.30 11.00 20.80 37.00 64.90 6
18、4.90 11.40 21.00 21.00 37.40 37.40 65.70 11.50 11.50 21.30 37.90 66.50 66.50 11.70 21.50 21.50 38.30 38.30 67.30 11.80 11.80 21.80 38.80 68.0012.00 12.00 22.00 39.00 68.10 68.10 12.10 12.10 22.10 22.10 39.20 39.20 69.00 12.30 22.30 39.70 69.80 69.80 12.40 12.40 22.60 22.60 40.20 40.20 70.60 12.60 22
19、.90 40.70 71.50 71.50 12.70 12.70 23.20 23.20 41.20 41.20 72.30 12.90 23.40 41.70 73.20 73.20 13.00 13.00 13.00 23.70 23.70 42.20 42.20 74.10 13.20 24.00 24.00 42.70 75.00 75.00 75.00 13.30 13.30 24.30 24.30 43.00 75.90 13.50 24.60 43.20 43.20 76.80 76.80 13.70 13.70 24.90 24.90 43.70 77.70 13.80 25
20、.20 44.20 44.20 78.70 78.70 14.00 14.00 25.50 25.50 44.80 79.60 14.20 25.80 45.30 45.30 80.60 80.60 14.30 14.30 26.10 26.10 45.90 81.60 14.50 26.40 46.40 46.40 82.0014.70 14.70 26.70 26.70 47.00 47.00 82.50 82.50 14.90 27.00 47.50 47.50 83.50 15.00 15.00 15.00 27.10 48.10 84.50 84.50 15.20 27.40 27.
21、40 48.70 48.70 85.60 15.40 15.40 27.70 49.30 86.60 86.60 15.60 28.00 28.00 49.90 49.90 88.70 88.7015.80 15.80 28.40 50.50 89.80 16.00 16.00 28.70 28.70 51.00 90.90 90.90 16.20 16.20 29.10 51.10 51.10 91.0016.40 29.40 29.40 51.70 92.00 93.10 16.50 16.50 29.80 52.30 52.30 93.10 16.70 30.00 53.00 94.20
22、 95.30 16.90 16.90 30.10 30.10 53.60 53.60 95.30 17.20 30.50 54.20 96.50 97.60 17.40 17.40 30.90 30.90 54.90 54.90 97.60 17.60 31.20 55.60 98.8017.80 17.80 31.60 31.60 56.00 18.00 18.00 32.00 56.20 56.20 18.20 18.20 32.40 32.40 56.9032.80 57.60 57.60 33.00 1/ Resistance values not listed in table II
23、 for the appropriate resistance tolerance will be considered as not conforming to the specification. The resistance values for tolerances B, C, and D may be any value within the limits specified in 3.3.2, but it is preferred that values be chosen from “B”, “C” and “D” column of table II. Provided by
24、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09013 REV PAGE 5 3.3.2 Resistance temperature characteristic. Unless otherwise specified, the resistance temperature characteristi
25、c shall be 100 ppm/OC. 3.3.3 Resistance tolerance. Networks are available in resistance tolerances as specified in table III. TABLE III Resistance tolerance. Symbol Resistance tolerance percent Available resistance range (in ohms) Schematic A Schematic B F 1.0 10 to 4.7K 10 to 2.2K G 2.0 J 5.0 10 to
26、 10K 10 to 4.7K 3.3.4 Resistor power rating. The resistor power rating for individual resistors shall be 100 milliwatts (.1 Watt) maximum at 70OC derated to zero watts at 85OC. 3.3.5 Package power rating. The package power rating shall be 600 milliwatts (.6 Watt) maximum at 70OC derated to zero watt
27、s at 85OC (see figure 2). FIGURE 2. Derating curve. 3.3.6 Schematic. The schematics of the resistor network are identified by a single letter in accordance with figure 3. Schematic A Schematic B FIGURE 3. Schematic. Percent of rated power-60 -40 -20 0 20 40 60 80 100 120 150 Temperature (OC) 100 80
28、60 40 20 0 70OC -40OC 85OC Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09013 REV PAGE 6 3.3.7 Pure tin. The use of pure tin, as an underplate or final finish, is p
29、rohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.4 Thermal shock. When networks are tested as specified in MIL-PRF-55342, for thermal shock the cha
30、nge in resistance shall not exceed 0.1 percent 0.01 ohm. 3.5 Low temperature operation. When networks are tested as specified in MIL-PRF-55342, for low temperature operation the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.6 Short time overload. When networks are tested as specifie
31、d in MIL-PRF-55342, for short time overload the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.7 High temperature exposure. When networks are tested as specified in MIL-PRF-55342, for high temperature exposure the change in resistance shall not exceed 0.1 percent 0.01 ohm. 3.8 Resist
32、ance to soldering heat. When networks are tested as specified in MIL-PRF-55342, for resistance to soldering heat the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.9 Moisture resistance. When networks are tested as specified in MIL-PRF-55342, for moisture resistance the change in res
33、istance shall not exceed 0.02 percent 0.01 ohm. 3.10 Resistance temperature characteristic. When networks are tested as specified in MIL-PRF-55342, the RTC shall not exceed the values specified (see 3.3.2). 3.11 Marking. Marking is not required on this resistor; however, each waffle pack and each un
34、it package shall be marked with the PIN assigned herein (see 1.2), the manufacturers identification code, the date code, and the lot code. At the option of the manufacturer, the resistor may be marked (i.e., laser, color dot, etc.). The marking shall remain legible after all tests. 3.12 Manufacturer
35、 eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-55342 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA
36、. 3.12.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as approved sources of supply. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used t
37、o the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. 3.14 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and be free from defects that wi
38、ll affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09013 REV PAGE 7 4. VERIFICATION 4.1 Qualification inspection. Qualifica
39、tion inspection in accordance with MIL-PRF-55342 is not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A and B inspections of MIL-PRF-55342. 4.2.1.1 Group A inspection. Group A inspectio
40、n shall be in accordance with MIL-PRF-55342 with the following exceptions. 4.2.1.1.1 Visual Inspection. The visual inspection of Subgroup 1 is not required. 4.2.1.1.2 Solderability. The method for solderability test for Subgroup 4 shall be conducted per manufacturers standard practice. All terminati
41、ons shall exhibit a continuous solder coating free from defects for a minimum of 95 percent of the critical surface area of any individual termination. Anomalies other than dewetting, non-wetting, and pinholes are not cause for rejection. 4.2.1.2 Group B inspection. Group B inspection shall be in ac
42、cordance with MIL-PRF-55342. 4.2.1.2.1 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 5. PACKAGING 5.1 Packaging. For acquisition purpose, the packaging requirements shall be a
43、s specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Contro
44、l Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible p
45、ackaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will
46、 perform the required function are not available for the OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery; One copy of the conformance inspection data or a certificate of compliance that parts hav
47、e passed conformance inspection with each shipment of parts by the manufacturer. c. Packaging requirements (see 5.1). (i.e. Electrostatic discharge sensitive packaging). d. Whether the manufacturer performs the group B tests or provides certificate of compliance with group B (see 4.2.1.2.1). Provide
48、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09013 REV PAGE 8 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coating
