1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Ken Bernier DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 21 October 2009 CHECKED BY K
2、en Bernier TITLE CAPACITORS, TANTALUM, HYBRID, HERMETICALLY SEALED APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09021 REV PAGE 1 OF 8 AMSC N/A 5910-E435 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproductio
3、n or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09021 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for tantalum hybrid capacitors, hermetically sealed in welded tantalum case with glas
4、s to metal anode terminal. 1.2 General. The capacitor shall utilize a sintered tantalum anode and ruthenium oxide coated cathodes operating in aqueous electrolyte. The components shall be hermetically sealed in a welded tantalum case with a glass to metal terminal seal. 1.3 Part or Identifying Numbe
5、r (PIN). The complete PIN is as follows: 09021- | | XX | |Drawing Dash number _ number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent spe
6、cified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). STANDARDS DEPARTMENT OF DEFENSE MIL-STD-202 - Test Methods for Electronic and Electrical Components Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (C
7、opies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of
8、 this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
9、e from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09021 REV PAGE 3 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Case. The case shall be tantalum. 3.1.2 M
10、ass. 0 50 volt parts: 104 3 grams; 63 125 volt parts: 128 3 grams. 3.1.3 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a mini
11、mum of 3 percent lead, by mass (see 6.3). 3.1.4 Storage temperature. The storage temperature shall be -62C to +130C. 3.1.5 Operating temperature range. The operating temperature range shall be -55C to +85C, de-rated to +125C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage sha
12、ll be in accordance with Table I at -55C to +85C, de-rated to + 125C. 3.2.2 Surge voltage. The test shall be 1000 cycles of rated surge voltage at 85C. Each cycle shall consist of a 30 second surge voltage application followed by a 330 second discharge period. The part shall be charged and discharge
13、d through a 1000 ohm resistor. The capacitor must not be visible damaged and the electrical characteristics must remain within specification. 3.2.3 Dielectric. The dielectric shall be an aqueous electrolyte. 3.2.4 DC leakage current. The maximum DC leakage current shall be as specified in Table I fo
14、llowing 5 minutes at the working voltage and 25C (see Table II). 3.2.5 Capacitance. Capacitance shall be as specified in Table I at 120Hz and 25C, 20%. 3.2.6 Capacitance tolerance. The capacitance tolerance shall be 20 percent at +25C. 3.2.7 Equivalent series resistance (ESR). The maximum equivalent
15、 series resistance (ESR) shall be as specified in Table I at 1 kHz and 25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09021 REV PAGE 4 NOTES: 1. Dimensions are i
16、n inches. 2. Metric equivalents are given for general information only. FIGURE 1. Case dimensions and configurationInches mm . .002 0.05 .003 0.08 .005 0.13 .010 0.25 .030 0.76 .040 1.02 .064 1.63 .230 5.84 .250 6.35 .400 10.16 .500 12.70 .615 15.62 .700 17.78 1.400 35.56 Provided by IHSNot for Resa
17、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09021 REV PAGE 5 TABLE I. Electrical characteristics. DSCC drawing 09021- Capacitance in (uF) 85C Rated voltage dc 125C Rated voltage dc Surge Vol
18、tage dc ESR max (ohms) Leakage current max (A) 01 02 03 04 05 06 07 08 09 10 11 200,000 130,000 75,000 50,000 30,000 16,000 10,000 9,000 7,000 6,000 4,200 10 16 25 35 50 63 80 85 100 110 125 6 9.5 15 20 30 38 48 51 60 65 75 11 18 28 39 55 69 88 94 110 127 138 0.025 0.025 0.035 0.035 0.035 0.035 0.04
19、0 0.050 0.050 0.065 0.065 400 400 400 400 500 500 600 600 600 600 600 3.3 Environmental characteristics. TABLE II. Environmental testing. Test Test Method Condition Details Shock MIL-STD-202 Method 213 G 11mS 50g Vibration MIL-STD-202 Method 204 D 12 Sweeps/Axis, 20g peak Vibration MIL-STD-202 Metho
20、d 214 I, Letter D 1.5 Hours/Axis, 12g rms Moisture Resistance MIL-STD-202 Method 106 6 V Polarity Thermal Shock MIL-STD-202 Method 107 A Altitude MIL-STD-202 Method 105 D 100,000 ft test 3.3.1 Thermal shock. Thermal shock test shall be as specified in Table II. 3.3.2 Moisture resistance. Moisture re
21、sistance test shall be as specified in Table II. 3.3.3 Hermetic Seal. The capacitor shall be hermetically sealed such that the case does not leak electrolyte or vent any gas when exposed to a vacuum, per MIL-STD-202, method 112, test condition C, procedure IIIa. 3.4 Physical characteristics. 3.4.1 S
22、hock . Shock test shall be as specified in Table II. 3.4.3 Resistance to solder heatMIL-STD-202, method 210, test condition B. The capacitor shall not be visibly damaged and the electrical characteristics shall not be affected. . The capacitor shall withstand solder dipping of the terminals at 260C
23、for 10 seconds per 3.4.4 Terminal strength. The capacitor terminals shall withstand a 5-pound pull test for 30 seconds per MIL-STD-202, method 211, test condition A. The capacitor shall not be visibly damaged and the electrical characteristics shall not be affected. 3.4.5 Solderability. The terminat
24、ions shall be solderable per MIL-STD-202, method 208. 3.4.6 Resistance to solvents. Resistance to solvents shall be in as specified in MIL-STD-202, method 215K. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS,
25、 OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09021 REV PAGE 6 3.4.7 Vibration. Vibration shall be as specified in table II. 3.4.8 Altitude. Barometric pressure (reduced). Capacitors shall be tested using MIL-STD-202, method 105, condition D. 3.4.9 Fungus. The capacitor materials shall not support fungu
26、s growth and shall not be a nutrient to fungus. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance re
27、quirements, and promotes economically advantageous life cycle costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.7 Manufacturer eligibility: To be eligible for listing as an approved source of supply
28、 a manufacturer shall perform all testing specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.8 Marking. Marking shall be in accordance with MIL-STD-1285, except the capacitor shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Comme
29、rcial and Government Entity (CAGE) code, date lot code and polarity. 3.9 Workmanship. The capacitor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2
30、Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of dc leakage, capacitance, and ESR. 4.2.2 Certification. The procuring activity, at its discretion, may accept a certificate of compliance for table II requirements in lieu of perform
31、ing table II tests. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09021 REV PAGE 7 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements s
32、hall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control
33、Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible pac
34、kaging activity. 6. NOTES (This section contains information of a general or explanatory nature, which may be helpful, but is not mandatory.) 6.1 Intended use. Hybrid capacitors covered by this drawing are intended mainly for use in defense electronic systems, avionics, and weapon systems. 6.2 Order
35、ing data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c.
36、 Requirements for packaging and packing. d. Requirements for notification of change of product to procuring activity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers ma
37、y occur anytime from a day to years after manufacturer and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown
38、 to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specifica
39、tion or drawing. 6.5 Similar vendor PINs. See table III. 6.6 Users of record. Coordination of this document for future revisions are coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in wri
40、ting to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdscc.dla.mil also by telephone (614) 692-0563 or DSN 850-0563. 6.7 Approved sources of supplyATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed
41、 to . Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, capacitorfilterdscc.dla.mil also by telephone (614) 692-0563 or DSN 850-0563. Provided by IHSNot for Resa
42、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09021 REV PAGE 8 Table III. Similar vendor PIN. DSCC PIN 09021- 1/ Vendor similar PIN 01 02 03 04 05 06 07 08 09 10 11 THS3010204 THS3016134 THS30
43、25753 THS3035503 THS3050303 THS3063163 THS3080103 THS3085902 THS3100702 THS3110602 THS3125422 1/ Parts must be purchased to this DSCC PIN to assure all performance requirements and tests are met. Vendor CAGE Vendor name Number and address06MN5 Evans Capacitor Company 72 Boyd Avenue East Providence, RI 02914-1202 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
