1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS REV OF PAGES PAGES PMIC N/A PREPARED BY John Bonitatibus DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 8 January 2013 CHECKED BY Yeasvina Afroz
2、 TITLE CAPACITORS, FIXED, MULTIPLE ANODE TANTALUM, CHIP, CONFORMAL COATED CASE APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 13008 SCALE N/A REV PAGE 1 OF 8 AMSC N/A 5910-2013-E04Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-D
3、LA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13008 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the complete requirements for tantalum chip capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 13008 -001 K E S A Drawing Dash Capa
4、citance Termination Reliability Surge current number number tolerance finish grade option (see table I) (see 1.2.1) (see 1.2.2) (see 1.2.3) (see 1.2.4) 1.2.1 Capacitance tolerance. The capacitance tolerance is identified by a single letter as follows: K = 10 percent, M = 20 percent. 1.2.2 Terminatio
5、n finish. The termination finish is identified by a single letter as follows: E = solder plated. 1.2.3 Reliability grade. The reliability grade is identified by a single letter as follows: S = Voltage Aging 1.2.4 Surge current option. The optional surge current testing is identified by a single lett
6、er as described in MIL-PRF-55365 and as follows: A, B, C, or Z. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for
7、additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government do
8、cuments. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENS
9、E SPECIFICATIONS MIL-PRF-55365 - Capacitor, Fixed, Electrolytic (Tantalum), Chip, Established Reliability, Nonestablished Reliability, and High Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts, Test Methods for. (Copies o
10、f these documents are available online at https:/assist.dla.mil/quicksearch or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between th
11、e text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo
12、reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13008 REV PAGE 3 Case code L (max.) W H A B D (ref.) J (max.) V .299 .173 .016 .079 max. .051 .012 .181 .024 .252 .004 (7.6) (4.4 0.4) (2.0 max.) (1.3 0.3) (4.6
13、0.6) (6.4) (0.1) D .299 .173 .016 .138 max. .051 .012 .181 .024 .252 .004 (7.6) (4.4 0.4) (3.5 max.) (1.3 0.3) (4.6 0.6) (6.4) (0.1) E .299 .173 .016 .157 .016 .051 .012 .181 .024 .252 .004 (7.6) (4.4 0.4) (4.0 0.4) (1.3 0.3) (4.6 0.6) (6.4) (0.1) R .299 .238 .016 .142 .016 .051 .012 .181 .024 .244
14、.004 (7.6) (6.0 0.4) (3.6 0.4) (1.3 0.3) (4.6 0.6) (6.2) (0.1) F .299 .238 .016 .185 .016 .055 .016 .181 .024 .244 .004 (7.6) (6.0 0.4) (4.7 0.4) (1.4 0.4) (4.6 0.6) (6.2) (0.1) Z .299 .238 .016 .236 .016 .055 .016 .181 .024 .244 .004 (7.6) (6.0 0.4) (6.0 0.4) (1.4 0.4) (4.6 0.6) (6.2) (0.1) M .315
15、.260 + .016/- .024 .142 .016 .051 .012 .197 .024 .260 .004 (8.0) (6.6 + 0.4/- 0.6) (3.6 0.4) (1.3 0.3) (5.0 0.6) (6.6) (0.1) H .315 .260 + .016/- .024 .205 .016 .055 .016 .197 .024 .260 .004 (8.0) (6.6 + 0.4/- 0.6) (5.2 0.4) (1.4 0.4) (5.0 0.6) (6.6) (0.1) N .315 .260 + .016/- .024 .252 .016 .055 .0
16、16 .197 .024 .260 .004 (8.0) (6.6 + 0.4/- 0.6) (6.4 0.4) (1.4 0.4) (5.0 0.6) (6.6) (0.1) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given in parenthesis for general information only. 3. These capacitors are designed for mounting by dip soldering, reflow soldering, or other convent
17、ional means. 4. The anode termination (D less B) shall be a minimum of .012 inch (0.3 mm). 5. These capacitors shall have a minimum of two bonding pads (top and bottom), on the major (width) dimension. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking
18、 permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13008 REV PAGE 4 TABLE I. Electrical characteristics. DLA Land and Maritime drawing PIN 13008- 1/ Capacitance F DC leakage (max) A Dissipation factor (max) % Max ESR 100 kHz +25C Ohms Cas
19、e code +25C +85C +125C +25C +85C +125C -55C 4 VDCat + 85 C, 2.7 VDCat + 125 C, 5.2 VDCsurge at + 85C 001-ES- 470 18.8 188 225.6 8 10 12 60 V 002-ES- 680 27.2 272 326.4 6 8 10 25 E 003-ES- 1000 40.0 400 480 8 10 12 20 E 004-ES- 1000 40.0 400 480 8 10 12 18 R 005-ES- 1500 60.0 600 720 8 10 12 24 R 6.3
20、 VDCat + 85 C, 4 VDCat + 125 C, 8 VDCsurge at + 85C 010-ES- 330 20.8 208 249.6 8 10 12 56 V 011-ES- 470 29.6 296 355.2 6 8 10 30 E 012-ES- 680 42.8 428 513.6 6 8 10 25 E 013-ES- 1000 63.0 630 756 8 10 12 31 R 10 VDCat + 85 C, 7 VDCat + 125 C , 13 VDCsurge at + 85C 020-ES- 330 33.0 330 396 6 8 10 35
21、E 021-ES- 470 47.0 470 564 6 8 10 28 E 022-ES- 680 68.0 680 816 6 8 10 28 R 023-ES- 1000 100.0 10000 12000 20 24 30 120 F 16 VDCat + 85 C, 10 VDCat + 125 C, 20 VDCsurge at + 85C 030-ES- 220 35.2 352 422.4 8 10 12 60 E 031-ES- 330 52.8 528 633.6 10 12 15 100 F 032-ES- 470 75.2 752 902.4 14 17 21 100
22、H 20 VDCat + 85 C, 13 VDCat + 125 C, 26 VDCsurge at + 85C 040-ES- 220 44.0 440 528 8 10 12 80 R 041-ES- 330 66.0 660 792 10 12 15 100 F 042-ES- 330 66.0 660 792 10 12 15 100 H 25 VDCat + 85 C, 17 VDCat + 125 C, 32 VDCsurge at + 85C 050-ES- 68 17.0 170 204 6 8 10 100 R 051-ES- 100 25.0 250 300 8 10 1
23、2 100 F 052-ES- 150 37.5 375 450 8 10 12 80 F 053-ES- 220 55.0 550 660 8 10 12 100 M 35 VDCat + 85 C, 23 VDCat + 125 C, 46 VDC surge at + 85C 060-ES- 47 16.5 165 198 6 8 10 100 R 061-ES- 68 23.8 238 285.6 6 8 10 100 F 062MES- 100 35.0 350 420 8 10 12 100 F 50 VDCat + 85 C, 33 VDCat + 125 C, 60 VDC s
24、urge at + 85C 070-ES- 15 7.5 75 90 6 8 10 350 E 071-ES- 15 7.5 75 90 6 8 10 250 R 072-ES- 22 11.0 110 132 6 8 10 220 R 073-ES- 33 16.5 165 198 6 8 10 150 F 074-ES- 47 23.5 235 282 6 8 10 240 Z 075-ES- 47 23.5 235 282 6 8 10 150 N 63 VDC at + 85 C, 42 VDC at + 125 C, 76 VDC surge at + 85C 080-ES- 10
25、10.0 100 120 6 8 10 400 D 081-ES- 15 9.5 95 114 6 8 10 400 R 082-ES- 22 13.9 139 166.8 6 8 10 250 F 1/ Complete PIN shall include additional symbols to indicate capacitance tolerance, and surge current option. If surge current is not required, the last “-“ shall be replaced with the letter Z (see 1.
26、2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13008 REV PAGE 5 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as spe
27、cified herein (see figure 1). 3.1.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6
28、.3). 3.1.2 Operating temperature range. The capacitors are rated for their given voltages from -55C to +85C. They are derated two thirds of their given voltages at +125C. See table I. 3.2 Electrical characteristics. 3.2.1 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-20
29、2. Maximum dc bias shall be 2.2 volts for all ac measurements. The frequency of the ac voltage shall be 120 5 Hz and the magnitude shall be limited to 1.0 volt rms. 3.2.2 Capacitance tolerance. K = 10 percent, M = 20 percent. 3.2.3 Rated voltage. The rated voltage shall be in accordance with table I
30、. Above +85C, voltage derating is required. De-rate linearly from rated voltage at +85C to 0.67 x rated voltage at +125C. 3.2.4 DC leakage (DCL). In accordance with MIL-PRF-55365 and table I. 3.2.5 Dissipation factor (DF). In accordance with MIL-PRF-55365 and table I. 3.2.6 Equivalent series resista
31、nce (ESR). In accordance with MIL-PRF-55365 and table I. 3.3 Surge current (optional). Surge current (when specified, see 1.2) shall be performed on a 100 percent basis either before or after Voltage Aging as indicated in 3.3b. The following details shall apply: a. Number of cycles: 10 at each tempe
32、rature. b. Temperature: Option A: (+25C 5C; after voltage aging). Option B: (-55C -5C, +0C and +85C 5C; after voltage aging). Option C: (-55C -5C, +0C and +85C 5C; before voltage aging). Option Z: No test required. c. Applied voltage: Rated dc voltage 2 percent from a power source having an energy s
33、torage bank of 50,000 F (minimum) across the output terminals. d. Charge cycle: 4 seconds 1 second. e. Discharge cycle: 4 seconds 1 second to a voltage below 1 percent of rated voltage. f. The total dc resistance (excluding the capacitor) including the wiring, fixturing, and output impedance of the
34、regulated power supply to each test position during the charging cycle shall be a maximum of 1.2 ohm. g. Upon completion of the test, the capacitors shall meet the following requirements: (1) DCL: See table I. (2) Capacitance: Shall meet the initial measured value. (3) DF: See table I. Provided by I
35、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13008 REV PAGE 6 3.4 Voltage Aging. Capacitors shall be subjected to a minimum of 100 percent of dc rated voltage for 40 hours, minimum, at a
36、temperature of +85C 5C in accordance with MIL-PRF-55365. 3.5 Additional tests. The capacitors specified herein are designed to meet the following requirements. Whether the tests are actually performed or not shall be at the option of the acquiring activity (see 6.2b) and shall be negotiable with the
37、 manufacturer. 3.5.1 Vibration, high frequency. Vibration, high frequency shall be in accordance with MIL-PRF-55365. 3.5.2 Thermal shock. Thermal shock shall be in accordance with MIL-PRF-55365, except the number of cycles shall be five. 3.5.3 Solderability. Solderability shall be in accordance with
38、 MIL-PRF-55365. 3.5.4 Surge voltage. Surge voltage shall be in accordance with MIL-PRF-55365. 3.5.5 Moisture resistance. Moisture resistance shall be in accordance with MIL-PRF-55365. 3.5.6 Stability at low and high temperatures. Stability at low and high temperatures shall be in accordance with MIL
39、-PRF-55365. 3.5.7 Resistance to soldering heat. Resistance to soldering heat shall be in accordance with MIL-PRF-55365. 3.5.8 Life. A minimum of dc rated voltage at +85C or a minimum of derated voltage at +125C for 2000 hours. 3.6 Recycled, recovered, or environmentally preferable materials. Recycle
40、d, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Marking. Marking shall be in accordance with MIL-
41、PRF-55365, except the “JAN“ or “J“ brand does not apply. The PIN shall be in accordance with 1.2. Marking is not required on the individual parts. 3.8 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-55365 Qualified P
42、roduct List for at least one part. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply. 3.10 Workmanship. Capacitors shall be uniform in quality and free from defects that will affect life, serviceabi
43、lity, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection (exponential distribution), subgroups 1 and 3,
44、of MIL-PRF-55365. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packagin
45、g activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military
46、Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 1
47、3008 REV PAGE 7 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will
48、perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for
