1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Pages 1-10, twenty parts added to drawing parts list and associated configurations added. 13 AUG 1986 Ivan Jones B Added dimension C to dash numbers 15-17 and 32-34 and changed marking requirements. Added black anodize finish option. Added dash numbers 35-4
2、4. 30 SEP 1987 Randy Larson C Added 5 additional part numbers. 1 DEC 1987 Clarence Brizius D Corrected dimensions on figure 1 and configurations E and F. Added an additional source of supply. 8 JUL 1988 Randy Larson E Corrected hole requirements on figure 1. 24 MAR 1989 Randy Larson F Changes in acc
3、ordance with NOR 5998-R004-95 15 MAY 1996 John Raye G Changes to Figure 1 in accordance with NOR 5998-R001-98 17 AUG 1998 Monica Poelking H Replaced canceled documents and corrected title. Editorial changes throughout. 31 MAR 2003 Thomas Hess J Added new sources of supply. 4 DEC 2013 Thomas Hess REV
4、 J J J PAGE 16 17 18 REV STATUS OF PAGES REV J J J J J J J J J J J J J J J PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PMIC N/A PREPARED BY DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 454445000 Christopher A Rauch Original date of drawing 27 August 1984 CHECKED BY TITLE Randy Larson H
5、OLDER, ELECTRICAL CARD, WEDGE RETAINER,3-PIECE, SCREW ACTUATED APPROVED BY Randy Larson SIZE CAGE CODE DWG. NO. 84103 A 14933 REV J PAGE 1 OF 18 AMSC N/A 5998E058CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DLA LAND AND MARITIME, COLUMBUS, OHIO 432183990 PINs 01 through 17 and 35
6、 through 44 are INACTIVE FOR NEW DESIGN AFTER 31 MARCH 2003 FOR NEW DESIGN USE CID A-A-59590 (see 6.5) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84103 RE
7、V J PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of metal card holders for use with printed circuit boards and circuit card assemblies in moderate shock and vibration environments. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 84103 Dr
8、awing number 49 Dash number (see table I) C Finish (B or C) (see 3.3 and 6.6) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or
9、 recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are liste
10、d. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (
11、see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MILDTL5002 Surface Treatments and Inorganic Coatings for Metal Surfaces of Weapon Systems. MILDTL5541 Chemical Conversion Coatings On Aluminum And Aluminum Alloys. MILA8625 Anodic Coatings For Aluminum And Aluminum Alloys. STANDARDS DEPARTMENT OF DEFENS
12、E MILSTD1285 Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Philadelphia, PA 191115094.) 2.3 Non-Government publications. The follow
13、ing documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS
14、 are the issues of the documents cited in the solicitation (see 6.2). AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. AIA/NAS NAS 620 Washer, Flat-Reduced Outside Diameter. AIA/NAS NAS 1676 Washer, Lock-Spring, Helical, Hi-Collar. AIA/NAS NASM35338 Washer, Lock-Spring, Helical, Regular (Medium) Se
15、ries. AIA/NAS NASM122116-122155 Insert, CRES Helical Coil, Coarse Thread, 1-1/2 Dia. Nominal Length. AIA/NAS NASM21043 Nut, Self-Locking, 800 F, Reduced Hexagon, Reduced Height, Ring Base, CRES. AIA/NAS NASM39086 Pin, Spring, Tubular, Coiled, Heavy Duty. (Copies of these documents are available onli
16、ne at http:/www.aiaaerospace.org or from the Aerospace Industries Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 222093901.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CO
17、DE IDENT NO. DWG NO. A 14933 84103 REV J PAGE 3 ASTM INTERNATIONAL (ASTM) ASTM A313/A313M Standard Specification for Stainless Steel Spring Wire. ASTM A484/A484M Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings. ASTM A580/580M Standard Specification for
18、 Stainless Steel Wire. ASTM A582/582M Standard Specification for Free-Machining Stainless Steel Bars. ASTM A666 Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. ASTM B194 Standard Specification for Copper-Beryllium Alloy Plate, Sheet, S
19、trip, and Rolled Bar. ASTM B221 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles and Tubes. (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 1942
20、82959.) SAE INTERNATIONAL (SAE) SAE AMS-QQ-A-200/8 Aluminum Alloy 6061, Bar, Rod, Shapes, Tube, and Wire, Extruded. SAE AMS-QQ-S-763 Steel, Corrosion Resistant, Bars, Wire, Shapes, and Forgings. SAE AMS 5525 Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 15Cr - 25.5Ni - 1.2Mo - 2.1Ti -
21、 0.006B - 0.30V 1800 F (982 C) Solution Heat Treated. SAE AMS 5643 Steel, Corrosion Resistant, Bars, Wire, Forgings, Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb - 4.0Cu Solution Heat Treated, Precipitation Hardenable. SAE AMS 5904 Steel, Corrosion-Resistant, Sheet and Strip 18Cr - 9.0Ni (SAE 30302) Cold
22、 Rolled 1/2 Hard, 150ksi (1034 MPa) Tensile Strength. (Copies of these documents are available online at http:/www.sae.org or from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 150960001.) (Non-Government standards and other publications are normally available from the organizations
23、 which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references
24、 cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. 3.1.1 Recommended torque. The recommended installation torque
25、 for the card holder assembly is 6 inch-pounds (0.7 N-m). 3.1.2 Locking feature. Dash numbers 18 through 34 and 45 through 49 are supplied with a locknut which prevents the disassembly of card holder once installed onto the circuit card assembly. 3.1.3 Mounting to circuit card assembly. These card h
26、olders are fastened to the circuit card assembly using either rivets or by brazing. Some card holders conforming to this drawing may be supplied in a unassembled condition. See 6.7 for additional information. 3.2 Materials. 3.2.1 Body and wedges. The body and wedge material shall be aluminum alloy i
27、n accordance with SAE AMS-QQ-A-200/8 or ASTM B221. 3.2.2 Captive nut (when applicable). The captive nut material shall stainless steel in accordance with ASTM A582/582M (CRES 303). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS S
28、UPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84103 REV J PAGE 4 3.2.3 Cup. The cup material for visual indicators shall stainless steel in accordance with ASTM B194 or SAE AMS 5904. 3.2.4 Flat washer. The flat washer (included with the locking feature) shall comply with AIA/
29、NAS NAS 620 or equivalent. 3.2.5 Locknut. The lock nut material shall be stainless steel in accordance with SAE AMS 5525 (A286). 3.2.6 Lockwasher. The lockwasher (included with the locking feature) shall comply with AIA/NAS NASM35338, AIA/NAS NAS 1676, or equivalent. 3.2.7 Screw. The screw material
30、for dash numbers 01 through 17 and 35 through 44 shall be stainless steel in accordance with SAE AMS-QQ-S-763, ASTM A484/A484M or ASTM A582/582M (303 CRES). The screw material for dash numbers 18 through 34 and 45 through 49 shall be stainless steel in accordance with SAE AMS 5643 (17-4PH, CRES) wit
31、h 155,000 pounds per square inch (1068 MPa) minimum yield strength. 3.2.8 Screw retention. 3.2.8.1 Captive nut. When a captive nut is used, the captive nut material shall be stainless steel, type 303, in accordance with ASTM A582/582M. 3.2.8.2 Helical insert. When a helical insert is used, the helic
32、al insert shall be in accordance with AIA/NAS NASM122116. 3.2.9 Spring. The spring material for visual indicators shall be stainless steel in accordance with ASTM A313/A313M or ASTM A580/580M. 3.3 Finish. 3.3.1 Bodies and wedges. The bodies and wedge finish shall be chemical finish in accordance wit
33、h MILDTL5541, class 1A or black anodize in accordance with MILA8625, type I or II, class 2. Card holders with a chemical film finish shall include a suffix “C“ in the PIN. Card holders with a black anodize finish shall include a suffix “B“ in the PIN (see 1.2). 3.3.2 Captive nut and cup (when applic
34、able). The captive nut and cup shall be passivate in accordance with MILDTL5002. 3.3.3 Flat washer and lockwasher The flat washer and lockwasher, captive nut, helical insert, and screw shall be passivate in accordance with MILDTL5002. 3.3.4 Screw and spring. The screw and spring shall be passivate i
35、n accordance with MILDTL5002. 3.4 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in 6.7. The certificate of compliance submitted to DLA Land and Maritime VAC, prior to listing as an suggested source o
36、f supply in 6.7, shall state that the manufacturers product meets the requirements herein. 3.5 Optional statement of compliance in lieu of performing conformance inspections. The acquiring activity, at its discretion, may accept from the manufacturer a statement of compliance in lieu of the manufact
37、urer performing the inspection of product for delivery tests (see 4.2.2 and 6.2.b). 3.6 Marking. Marking of the card holder is not required; however, each unit package shall be marked in accordance with MILSTD1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercia
38、l and Government Entity (CAGE) code, and date lot codes. 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and mainte
39、nance requirements, and promotes economically advantageous life cycle costs. 3.8 Workmanship. Card holders shall be free from surface and finish flaws that affect life or serviceability. Card holders shall be finished smooth and shall have rounded edges with no evidence of chipping, cracking, deteri
40、oration, disintegration, or burrs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84103 REV J PAGE 5 TABLE I. Configurations and di(0.8 mm)mensions. PIN 84103
41、 Dimension “L“ .03 inch (0.8 mm) Dimension “A“ +.03 / .09 inch (+0.8 / 2.9 mm) Dimension “B“ 0.03 inch (0.8 mm) Dimension “C“ 0.005 inch (0.13mm) Configuration Inches mm Inches mm Inches mm Inches mm 01 2.80 71.1 3.00 76.2 2.30 58.4 .90 22.9 A and B 1/ 02 3.00 76.2 3.20 81.3 2.50 63.5 1.10 27.9 03 3
42、.50 88.9 3.70 94.0 3.00 76.2 1.60 40.6 04 3.80 96.5 4.00 101.6 3.30 83.8 1.90 48.3 05 4.80 121.9 5.00 127.0 4.30 109.2 2.90 73.7 06 5.30 134.6 5.50 139.7 4.80 121.9 3.40 86.4 07 5.80 147.3 6.00 152.4 5.30 134.6 3.90 99.1 08 2.80 71.1 3.20 81.3 2.30 58.4 .90 22.9 A, B, and C 1/ 09 3.00 76.2 3.40 86.4
43、 2.50 63.5 1.10 27.9 10 3.50 88.9 3.90 99.1 3.00 76.2 1.60 40.6 11 3.80 96.5 4.20 106.7 3.30 83.8 1.90 48.3 12 4.80 121.9 5.20 132.1 4.30 109.2 2.90 73.7 13 5.30 134.6 5.70 144.8 4.80 121.9 3.40 86.4 14 5.80 147.3 6.20 157.5 5.30 134.6 3.90 99.1 15 2.80 71.1 3.00 76.2 1.95 49.5 .90 22.9 D 1/ 16 3.80
44、 96.5 4.00 101.6 2.95 74.9 1.90 48.3 17 4.80 121.9 5.00 127.0 3.95 100.3 2.90 73.7 18 2.80 71.1 3.10 78.7 2.30 58.4 .90 22.9 A B and E 19 3.00 76.2 3.30 83.8 2.50 63.5 1.10 27.9 20 3.50 88.9 3.80 96.5 3.00 76.2 1.60 40.6 21 3.80 96.5 4.10 104.1 3.30 83.8 1.90 48.3 22 4.80 121.9 5.10 129.5 4.30 109.2
45、 2.90 73.7 23 5.30 134.6 5.60 142.7 4.80 121.9 3.40 86.4 24 5.80 147.3 6.10 154.9 5.30 134.6 3.90 99.1 25 2.80 71.1 3.30 83.8 2.30 58.4 .90 22.9 A B C and E 26 3.00 76.2 3.50 88.9 2.50 63.5 1.10 27.9 27 3.50 88.9 4.00 101.6 3.00 76.2 1.60 40.6 28 3.80 96.5 4.30 109.2 3.30 83.8 1.90 48.3 29 4.80 121.
46、9 5.30 134.6 4.30 109.2 2.90 73.7 30 5.30 134.6 5.80 147.3 4.80 121.9 3.40 86.4 31 5.80 147.3 6.30 160.0 5.30 134.6 3.90 99.1 See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 4
47、54445000 SIZE CODE IDENT NO. DWG NO. A 14933 84103 REV J PAGE 6 TABLE I. Dash numbers and dimensions Continued. PIN 84103 Dimension “L“ .03 inch (0.8 mm) Dimension “A“ +.03 / .09 inch (+0.8 / 2.9 mm) Dimension “B“ .03 inch (0.8mm) Dimension “C“ .005 inch (0.13mm) Configuration Inches mm Inches mm In
48、ches mm Inches mm 32 2.80 71.1 3.00 76.2 1.95 49.5 .90 22.9 D and F 33 3.80 96.5 4.00 101.6 2.95 74.9 1.90 48.3 34 4.80 121.9 5.00 127.0 3.95 100.3 2.90 73.6 35 5.50 139.7 5.70 144.8 5.00 127.0 3.60 91.4 A and B 1/ 36 6.10 154.9 6.30 160.0 5.60 142.2 4.20 106.7 37 6.70 170.2 6.90 175.3 6.20 157.5 4.80 121.9 38 2.80 71.1 3.00 76.2 2.24 56.9 .90 22.9 G and H 1/ 39 3.00 76.2 3.20 81.3 2.44 62.0 1.10 27.9 40 3.50 88.9 3.70 94.0 2.94 74.7 1.60 40.6 41 3.80 96.5 4.00 101.6 3.24 82.3 1.90 48.3 42 4.80 121.9 5.00 127.0 4.24 107.7 2.90 73.7 43 5.30 134
