1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added an additional source of supply. Made standoffs optional. Correction to table I. 10 Nov 87 Randy Larson B Added additional source of supply. Added assistance paragraph. Changed the requirements for inspection of product for delivery. 5 Aug 88 Randy Lar
2、son C Added note 6 to figure 1. Expanded 3.29. Deleted vendors 56289 and 92912. Added vendors 20933 and 16714. Editorial changes throughout. JW 2 Oct 92 D. Moore D Incorporated editorial and boilerplate updates. 23 Jun 08 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control dra
3、wing REV D D D D D D D D D D REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Dan McGrath DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 CHECKED BY Dan McGrath APPROVED BY Ivan R. Jones TITLE DELAY LINES, ACTIVE, PROGRAMMABLE 3 BIT, 16 PIN DIP COMPATIBLE,
4、EMITTER-COUPLED LOGIC (ECL) SIZE A CODE IDENT. NO. 14933 DWG NO. 85078 Original date of drawing 6 Nov 85 REV D PAGE 1 OF 10 AMSC N/A 5999-E215CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo repr
5、oduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85078 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of programmable 3 bit, 16 pin compatible, emitter-coupled logi
6、c (ECL) delay lines. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example: 85078 -01 Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section
7、 does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in se
8、ctions 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues o
9、f these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-31000 - Technical Data Packages. MIL-PRF-83532 - Delay Lines, Active, General Specification For. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ o
10、r http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of
11、 these documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR TESTING AND MATERIALS INTERNATIONAL (ASTM) ASTM-B339 - Pig Tin. ASTM-B545 - Electrodeposited Coatings of Tin. (Copies of this document are available on www.astm.org or from American Society for Testing and Materia
12、ls International (ASTM), 100 Barr Harbor Drive, P. O. Box C700, West Conshohocken, PA, 19428-2959.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, su
13、persedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85078 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 3 3. REQUIREM
14、ENTS 3.1 Drawing precedence. This drawing takes precedence over documents referred to herein and shall be interpreted in accordance with MIL-DTL-31000. 3.2 Case material. The case material shall be molded diallyl phthalate or encapsulated epoxy and shall be in accordance with MIL-PRF-83532. 3.3 Dime
15、nsions and configuration. The dimensions and configuration shall be in accordance with figure 1. 3.4 Terminal material. The terminal material shall be copper-nickel or alloy 42, tin plated in accordance with ASTM - B339 and ASTM -B545. 3.5 Temperature coefficient of delay. The temperature coefficien
16、t of delay shall be +150 ppm/C maximum. 3.6 Maximum delay time. The maximum delay time shall be in accordance with table I. 3.7 Delay tolerance. The delay tolerance shall be in accordance with table I. 3.8 Rise time. The rise time shall be 5 ns maximum when measured from 20 percent to 80 percent pul
17、se amplitude. 3.9 Pulse width. For dash numbers 01 through 05, the pulse width shall be 20 ns. For all other dash numbers, the pulse width shall be 150 ns. 3.10 Supply voltage (VEE). The supply voltage shall be -5.2 V 5 percent. 3.11 Supply current. The supply current shall be 120 mA maximum. 3.12 L
18、ogic 1 input at +25C. The voltage shall be -0.98 V minimum and the current shall be 25 mA maximum. 3.13 Logic 0 input at +25C. The voltage shall be -1.63 V maximum and the current shall be 0.5 A minimum. 3.14 Logic 1 output at +25C. The voltage shall be -0.96 V minimum. 3.15 Logic 0 output at +25C.
19、The voltage shall be -1.65 V maximum. 3.16 Delay line fan-out. The delay lines are capable of driving 70 emitter-coupled logic dc loads. 3.17 Thermal shock. Thermal shock test shall be as specified in MIL-PRF-83532. 3.18 Sealing. The sealing test shall be in accordance with MIL-PRF-83532. 3.19 Termi
20、nal strength. Terminal strength test shall be as specified in MIL-PRF-83532. 3.20 Vibration. The vibration test shall be in accordance with MIL-PRF-83532. 3.21 Shock. Shock test shall be as specified in MIL-PRF-83532. 3.22 Immersion. The immersion test shall be in accordance with MIL-PRF-83532. Prov
21、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85078 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 4 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking perm
22、itted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85078 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 5 NOTES: Inches mm 1. Dimensions are in inches. .010 0.25 2. Metric equivalents are given for general information only. .012 0.30 3. Unless otherwise specified, tol
23、erance is .010 (0.25 mm). .018 0.46 4. Orientation dot appears over pin 1. .025 0.64 5. Location and shape of standoffs are optional. Height shall be as indicated. .030 0.76 6. Leads shall be free of case meniscus and other foreign material and shall .150 3.81 be solderable for a minimum of .010 inc
24、h above the seating plane of the .250 6.35 delay line. .300 7.62 .350 8.89 .360 9.14 .400 10.16 .900 22.86 FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85078 DEFENSE
25、ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 6 TABLE I. PINs and delay times. 1/ PIN 85078- 2/ Step zero delay time (ns) Maximum delay time (ns) Delay change per step (ns) 3/ Maximum deviation from programmed delay (ns) 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 3.0 2.0 “ “ “
26、 “ “ “ “ “ “ “ “ “ “ “ “ “ “ 10 17 24 31 38 45 52 59 66 73 108 143 178 213 248 283 318 353 1 0.3 2 0.4 3 0.5 4 0.5 5 0.5 6 0.6 7 0.7 8 0.8 9 0.9 10 1 15 1 20 1.5 25 1.5 30 2 35 2 40 2.5 45 2.5 50 2.5 0.5 or 5% (whichever is greater) “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ 1/ For maximum delay time, tabula
27、tion and truth table examples, a step zero delay time of 3 ns is assumed. 2/ Delay at step zero is referenced to the input pin. 3/ All delay times after step zero are referenced to step zero. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT
28、 NO. 14933 DWG NO. 85078 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 7 TABLE II. Truth table. Programming pins PIN 85078- 3 0 2 0 1 0 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 01 3 1 2 3 4 5 6 7 02 3 2 4 6 8 10 12 14 03 3 3 6 9 12 15 18 21 04 3 4 8 12 16 20 24 28 05 3 5 10 15 2
29、0 25 30 35 06 3 6 12 18 24 30 36 42 07 3 7 14 21 28 35 42 49 08 3 8 16 24 32 40 48 56 09 3 9 18 27 36 45 54 63 10 3 10 20 30 40 50 60 70 11 3 15 30 45 60 75 90 105 12 3 20 40 60 80 100 120 140 13 3 25 50 75 100 125 150 175 14 3 30 60 90 120 150 180 210 15 3 35 70 105 140 175 210 245 16 3 40 80 120 1
30、60 200 240 280 17 3 45 90 135 180 225 270 315 18 3 50 100 150 200 250 300 350 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85078 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 8 3.23 Moisture resista
31、nce. The moisture resistance test shall be as specified in MIL-PRF-83532. 3.24 Solderability. The solderability test shall be as specified in MIL-PRF-83532. 3.25 Truth table. See table II. 3.26 Operating temperature range. The operating temperature range shall be -55C to +125C. 3.27 Recycled, recove
32、red, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.
33、 3.28 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-83532 Qualified Product List for at least one part, or perform the Group A and Group B inspections specified herein on a sample of parts agreed upon by the manufa
34、cturer and DSCC-VA. 3.29 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.30 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resist
35、or components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.31 Marking. Marking shall be in accordance with MIL-PRF-83532, except that the military PIN shall be as specified in 1.2. 3.32 Workmanship. Delay lines shall be
36、processed in such a manner as to be uniform in quality and shall be free from defects that could affect life, serviceability or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, sampling and inspection procedures shall be performed in accordance with Inspection of
37、product for delivery shall consist of compliance with the group A inspection for level A of MIL-PRF-83532. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD o
38、r in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military se
39、rvices system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. Devices conforming to this drawing are intended for use
40、when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy
41、of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85078 DEFENSE
42、ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV D SHEET 9 c. Whether the manufacturer performs the group A inspection tests or provides a statement of compliance with group A requirements. d. Requirement for the manufacturer to notify the acquiring activity in the event of a change in product. e.
43、Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating
44、 conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to AS
45、TM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing m
46、ay be achieved online at mailto:relaydla.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. 6.5 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additiona
47、l sources will be added as they become available. Assistance in the use of this drawing may be obtained online at mailto:relaydla.mil, or by contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. Simil
48、ar vendor PIN and CAGE 1/ DESC drawing PIN 85078- 00222 16714 22519 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 96-88-1 96-88-2 96-88-3 96-88-4 96-88-5 96-88-6 96-88-7 96-88-8 96-88-9 96-88-10 96-88-11 96-88-12 96-88-13 96-88-14 96-88-15 96-88-16 96-88-17 96-88-18 DSP078-01 DSP078-02 DSP078-03 DSP078-04 DSP078-05 DSP078-06 DSP078-07 DSP078-08 DSP078-09 DSP078-10 DSP078-11 DSP078-12 DSP078-13 DSP078-14 DSP078-15 DSP078-16 DSP078-17 DS9078-18 PDU108H-8542-1 PDU108H-8542-2 PDU108H-8542-3 PDU108H-8542-4 PDU108H-8542-5 PDU108H-8542-
