1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Revised drawing to reflect MIL-D-83532 requirements. Editorial changes throughout. 14 Sep 1987 Randy Larson B Added minimum pulse width requirement. Added three suggested supply sources. Added notes 5 and 6 to figure 1. Changed several values in table II. E
2、ditorial changes throughout. 3 Apr 1989 Randy Larson C Add paragraph 3.5.1. Added tolerance to pin diameters on figure 1. Changed flat pin dimension in note 5. Editorial changes throughout. 13 Jan 1992 Randy Larson D Changes in accordance with NOR 5999-R004-92 9 Sep 1992 David Moore E Incorporated b
3、oilerplate update. Updated vendor addresses. Editorial changes throughout. 26 Sep 2000 Kendall A. Cottongim F Editorial changes and boilerplate updates made throughout. 14 May 2009 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV F F F F F F
4、F F F PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Dan McGrath DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 9 Oct 1985 CHECKED BY Dan McGrath TITLE DELAY LINE, THREE DELAY LINE UNITS, 14 PIN DIP COMPATIBLE, TTL INTERFACED APPROVED BY Ivan R. Jones
5、SIZE A CODE IDENT. NO. 14933 DWG NO. 85151 REV F PAGE 1 OF 9 AMSC N/A 5999-E207CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-D
6、EFENSE ELECTRONICS SUPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85151 REV F SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of active 14-pin DIP compatible TTL delay lines with three delay line units per package. 1.2 Part or Identifying Number (PIN).
7、 The complete PIN shall be as follows: 85151 -01 | | | | Drawing number Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this
8、 specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they a
9、re listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or co
10、ntract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-M-38510 - Microcircuits, General Specification for. MIL-PRF-38535 - Integrated Circuits (Microcircuits) Manufacturing, General Specification for. MIL-PRF-83532 - Delay Lines, Active, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1
11、285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of preced
12、ence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUI
13、REMENTS 3.1 Materials. Materials shall be as specified in MIL-PRF-83532. 3.1.1 Cases. Cases shall be molded diallyl phthalate or encapsulated epoxy and shall be in accordance with MIL-PRF-83532. 3.1.2 Solder and soldering flux. Solder and soldering flux shall be in accordance with MIL-PRF-83532. 3.2
14、 Interface and physical dimensions. See figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTORNICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85151 REV F SHEET 3 3.3 Terminal type. Terminals shall be printed-cir
15、cuit pin type in accordance with MIL-M-38510 and may be round or flat (see figure 1). 3.4 Operating temperature range. Operating temperature range shall be -55C to +125C. 3.5 Delay time. See table I. 3.5.1 Check for internal shorts. When a test signal is applied to any input, a delay signal should b
16、e detected at the output for that line only. For example, when input 1 is tested, there shall be no signals detected at outputs 2 and 3. All three inputs shall be checked in this manner. 3.6 Delay tolerance. At +25C, the delay tolerance shall be 2.0 ns or 5 percent, whichever is greater. At -55C or
17、+125C the delay tolerance shall be 3 ns or 8 percent, whichever is greater. 3.7 Rise time. The rise time shall be 4 ns maximum. 3.8 Pulse width. Minimum input pulse width shall be 100 percent of the total delay time. 3.9 Integrated circuits. Integrated circuits shall be tested to and meet the screen
18、ing requirements of MIL-PRF-38535. 3.10 DC characteristics. DC characteristics shall be in accordance with table II. 3.11 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided
19、 that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.12 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-83532 Qualified Products
20、 List for at least one part, or perform the Group A inspection specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.13 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.14 Pure
21、tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.15 Marking. Delay lines shall be ma
22、rked on the top of the case in accordance with method I of MIL-STD-1285, except the delay line shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, date lot codes, and an index mark next to pin 1 (see figure 1). 3.16 Work
23、manship. The delay line shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTORNICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 1
24、4933 DWG NO. 85151 REV F SHEET 4 FIGURE 1. Interface and physical dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTORNICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85151 REV F SHEET 5 NOTES: 1. Dimensions
25、are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. Location and shape of standoffs are optional within the dimensional limits specified. 5. Flat pins are optional. If used, the .020 (0.46 mm) side shall be paral
26、lel to the case length. 6. Circuit diagram depicts general characteristics and is not intended to limit standard vendor designs. 7. Leads shall be free of case meniscus and other foreign material and shall be solderable for a minimum of .010 inch (0.25 mm) above the seating plane of the delay line.
27、8. The pictorial view of alternative standoff is representative of the envelope item. Slight deviations from the outline shown, which are contained within the envelope, and do not alter the functional aspect of the device are acceptable. FIGURE 1. Interface and physical dimensions - Continued. LTR I
28、nches Millimeters Min Max Min Max A - .800 - 20.32 B - .400 - 10.16 C - .260 - 6.60 D .055 .065 1.40 1.65 E .025 .035 0.64 0.89 F .110 .150 2.79 3.81 G .018 DIA .022 DIA 0.46 DIA 0.56 DIA H .095 .105 2.41 2.67 J .295 .305 7.49 7.75 K .018 .022 0.46 0.56 L .008 .012 0.20 0.30 M .145 .155 3.68 3.94 N
29、.295 .305 7.49 7.75 R .142 .158 3.61 4.01 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTORNICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85151 REV F SHEET 6 4. VERIFICATION 4.1 Conformance inspection. 4.1.1 Samplin
30、g and inspection. Inspection of product for delivery shall consist of the group A, level A inspection in MIL-PRF-83532. Individual tests shall be performed in the order listed therein. 4.1.2 Certification. The acquiring activity, at its discretion, may accept a statement of compliance with the group
31、 A requirements in lieu of the manufacturer performing the group A tests (see 6.2c). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor
32、personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands
33、. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. TABLE I. PINs and delay times. DSCC drawing PIN 85151- Total delay per line (ns) 01 02 03 04 05 06 07 08
34、09 10 11 12 13 14 15 16 17 18 5 10 15 20 25 30 35 40 45 50 75 100 125 150 175 200 225 250 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTORNICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85151 REV F SHEET 7 TABLE II.
35、 DC characteristics. Test Symbol Conditions -55C TC +125C Limits Unit Min Max High level output voltage VOHVCC= 4.5 V, VIH= 2.0 V IOH= -1 mA 2.5 - V Low level output voltage VOLVCC= 4.5 V, VIL= 0.8 V IOL= 20 mA - 0.5 V Input clamp voltage VIKVCC= 4.5 V, TC= +25C - -1.5 V High level input current IIH
36、1VCC= 5.5 V, VIH= 2.7 V - 50 A IIH2VCC= 5.5 V, VIH= 5.5 V - 1,000 A Low level input current IILVCC= 5.5 V, VIL= 0.5 V - -2.00 mA Short-circuit output current IOSVCC= 5.5 V, VOS= 0.0 V Not more than one output shorted at a time -40 -150 mA Low level supply current I VCC= 5.5 V, VI= 0.0 V - 115 mA Out
37、put rise time (applied to leading edge only) TROVCC= 5.0 V, TRI 3 ns CL= 15 pF, RL= 1 megohm - 4 ns 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Delay lines conforming to this drawing are intended for us
38、e when military specifications do not exist and qualified military devices that will perform the required function are not available for the OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, and o
39、ne copy of the conformance inspection data or the certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group A inspection tests or provides a statement of compliance with group A requirements
40、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTORNICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85151 REV F SHEET 8 d. Requirement for the manufacturer to notify the acquiring activity in the event of a change in
41、product. e. Requirements for packaging and packing. 6.3 Tin whisker growth6.4 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawin
42、g may be achieved online at . The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use
43、such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification fo
44、r Electrodeposited Coatings of Tin). mailto:relaydla.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. 6.5 Approved source(s) of supply. Approved source(s) of supply are listed herei
45、n. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at mailto:relaydla.mil, or by contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850
46、-4481. Vendor CAGE Vendor name and address Vendor CAGE Vendor name and address 22519 Data Delay Devices, Inc. 3 Mount Prospect Avenue Clifton, NJ 07013-1915 (973) 772-2299 16714 Rhombus Industries, Inc. 313 N Birch Street Santa Ana, CA 92701-5263 (714) 898-0960 00222 ESC Electronics Inc. 33 Comac Lo
47、op Ronkonkoma, NY 11779-6858 (614) 467-5328 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTORNICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85151 REV F SHEET 9 DSCC drawing PIN 85151- Similar vendor designation or t
48、ype number 1/ CAGE 00222 CAGE 16714 CAGE 22519 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 95-31-005 95-31-010 95-31-015 95-31-020 95-31-025 95-31-030 95-31-035 95-31-040 95-31-045 95-31-050 95-31-075 95-31-100 95-31-125 95-31-150 95-31-175 95-31-200 95-31-225 95-31-250 DSP151-01 DSP151-02 DSP151-03 DSP151-04 DSP151-05 DSP151-06 DSP151-07 DSP151-08 DSP151-09 DSP151-10 DSP151-11 DSP151-12 DSP151-13 DSP151-14 DSP151-15 DSP151-16 DSP151-17 DSP151-18 MDU3-8547-5 MDU3-8547-10 MDU3-8547-15 MDU3-8547-20 MDU3-8547-25 MDU3-8547-30 MDU3-8547-
