1、REVISIONS LTR DESCRIPTION DATE APPROVED A Add source CAGE 91506. 19 October 1987 R. Marbais B Change marking requirement. Add caution note. 22 November 1988 R. Marbais C Change marking requirement. Change 86103 wire size from 36 AWG to 32 AWG. 15 May 1990 R. Marbais D Remove CAGE 22526 and add CAGE
2、8N187. Remove reference to DESC and change to DSCC. Remove 91506. 26 August 1998 C. W. Koeller E Change CAGE 14933 to 037Z3. Editorial changes throughout. 3 October 2002 R. Heber F Updating CAGE (8N187) PINs. Editorial changes throughout. 17 May 2010 Abdo Abdouni Prepared in accordance with ASME Y14
3、.100 Source control drawing REV PAGE REV STATUS OF PAGES REV F F F F PAGE 1 2 3 4 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-39900 Gail Willis Original date of drawing 19 September 1986 CHECKED BY TITLE Carl Dello-Stritto CONNECTORS, RECEPTACLE, ELECTRICAL, LATCH HOUSI
4、NGS, SINGLE ROW, .025 POSTS APPROVED BY Richard Marbais SIZE CAGE CODE DWG. NO. 86060 A 037Z3 REV F PAGE 1 OF 4 AMSC N/A 5935-E831-003 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-3990 SIZE CAGE C
5、ODE DWG NO. A 037Z3 86060 REV F PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, all tolerances are .005 (0.13 mm). FIGURE 1. Dimensions and configurations. Inches mm .005 0.13 .010 0.25 .038 0.97 .100 2.54 .215 10.16 .55
6、0 13.97 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86060 REV F PAGE 3 REQUIREMENTS: Shall meet the requirements of drawing number 86037. Design and constructi
7、on: Dimensions and configuration: See figure 1 and table I. Interface: Drawing number 86103 receptacle contacts crimped to 22 AWG through 32 AWG wire, .100 inch (2.54 mm) centers, .025 inch (0.64 mm) round or square posts. Polarization pin see drawing 87121. Temperature range: -40C to +105C. Materia
8、ls: Housing: Polyphenylene oxide-based resin and shall meet the flammability requirements of UL 94 V-0. Dielectric withstanding voltage: 1,000 volts rms, 60 Hz, sea level. Contact retention: 6.5 pounds (3 Kg), minimum per position. Marking: The Part or Identifying Number (PIN) shall be marked on the
9、 housing and package in accordance with MIL-STD-1285. If size, surface conditions, or other design considerations dont allow for full marking on the part, marking on the package is only required. The PIN shall include the complete DSCC PIN, manufacturers name or CAGE code, and date code. The marking
10、 shall be permanent and legible in accordance with method 215 of MIL-STD 202. The PIN shall be constructed using the follow format: 86060 - XX DSCC drawing Number of positions number (see table I) TABLE I. Number of positions. Number of positions Dimension A (mm) Number of positions Dimension A (mm)
11、 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 .100 (2.54 .200 (5.08) .300 (7.62) .400 (10.16) .500 (12.70) .600 (15.24) .700 (17.78) .800 (20.32) .900 (22.86) 1.000 (25.40) 1.100 (27.94) 1.200 (30.48) 1.300 (33.02) 1.400 (35.56) 1.500 (38.10) 1.600 (40.64) 1.700 (43.18) 1.800 (45.72) 19 20
12、21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 1.900 (48.26) 2.000 (50.80) 2.100 (53.34) 2.200 (55.88) 2.300 (58.42) 2.400 (60.96) 2.500 (63.50) 2.600 (66.04) 2.700 (68.58) 2.800 (71.12) 2.900 (73.66) 3.000 (76.20) 3.100 (78.74) 3.200 (81.28) 3.300 (83.82) 3.400 (86.36) 3.500 (88.90) 3.600 (91.44)
13、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86060 REV F PAGE 4 Approved sources of supply are listed herein. Additional sources will be added as they become av
14、ailable. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ 86060-01 8N187 65039-036LF-MIL 86060-02 8N187 65039-035LF-MIL 86060-03 8N187 65039-034LF-MIL 8
15、6060-04 8N187 65039-033LF-MIL 86060-05 8N187 65039-032LF-MIL 86060-06 8N187 65039-031LF-MIL 86060-07 8N187 65039-030LF-MIL 86060-08 8N187 65039-029LF-MIL 86060-09 8N187 65039-028LF-MIL 86060-10 8N187 65039-027LF-MIL 86060-11 8N187 65039-026LF-MIL 86060-12 8N187 65039-025LF-MIL 86060-13 8N187 65039-0
16、24LF-MIL 86060-14 8N187 65039-023LF-MIL 86060-15 8N187 65039-022LF-MIL 86060-16 8N187 65039-021LF-MIL 86060-17 8N187 65039-020LF-MIL 86060-18 8N187 65039-019LF-MIL 86060-19 8N187 65039-018LF-MIL 86060-20 8N187 65039-017LF-MIL 86060-21 8N187 65039-016LF-MIL 86060-22 8N187 65039-015LF-MIL 86060-23 8N1
17、87 65039-014LF-MIL 86060-24 8N187 65039-013LF-MIL 86060-25 8N187 65039-012LF-MIL 86060-26 8N187 65039-011LF-MIL 86060-27 8N187 65039-010LF-MIL 86060-28 8N187 65039-009LF-MIL 86060-29 8N187 65039-008LF-MIL 86060-30 8N187 65039-007LF-MIL 86060-31 8N187 65039-006LF-MIL 86060-32 8N187 65039-005LF-MIL 86
18、060-33 8N187 65039-004LF-MIL 86060-34 8N187 65039-003LF-MIL 86060-35 8N187 65039-002LF-MIL 86060-36 8N187 65039-001LF-MIL 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 8N187 T.T.I 2601 SYLVANIA CROSS DR FORT WORTH, TX 76137 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
