1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new source of supply; change temperature coefficient of schematics 8, 11, and 13. Editorial changes throughout. 20 May 88 D. MOORE B Changes in accordance with NOR 5905-R012-93. 28 May 93 D. MOORE C Update and validation of drawing. Editorial changes th
2、roughout. 11 Sep 00 K. COTTONGIM D Add pure tin prohibition paragraph. Editorial changes throughout. 29 Jan 07 M. RADECKI CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item
3、drawing REV STATUS OF PAGES REV D D D D D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Alan R. Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing: CHECKED BY David W. Withrow TITLE RESISTOR NETWORK, FIXED, FILM, 10-PIN SIP,
4、MULTIPLE RESISTANCE VALUES, MULTIPLE 29 December 1987 APPROVED BY David E. Moore SCHEMATICS AND MULTIPLE TOLERANCES. SIZE A CODE IDENT. NO. 14933 DWG NO. 87072 REV D PAGE 1 OF 12 AMSC N/A 5905-E625 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFE
5、NSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 10-pin, single-in-line package (SIP), fixed, film, resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows
6、: 87072 - 01 Drawing number Schematic number (see figure 2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified
7、, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARD
8、S MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Orde
9、r of precedence. In the event of a conflict between the text of this document and the references cited herein, (except for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes appli
10、cable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item Requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physic
11、al dimensions as specified in MIL-PRF-83401 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 3 Inches mm Inches mm Inches mm
12、0.002 0.05 0.019 0.48 0.125 3.17 0.005 0.006 0.12 0.15 0.098 0.100 2.48 2.54 0.320 1.000 8.12 25.40 0.010 0.25 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, dimensional tolerances shall be 0.02 (0.5 mm) for two decima
13、l places and 0.010 (0.25 mm) for three decimal places. 4. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are accepta
14、ble. FIGURE 1. Resistor network. 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance value shall be as specified on figure 2. 3.3.2 Resistance tolerance. The resistance tolerance shall as specified on figure 2. 3.3.3 Resistor power rating. The resistor power rating for individual resist
15、ors shall be 125 milliwatts maximum at 70oC derated to 0 watts at 150oC. 3.3.4 Package power rating. The package power rating shall not exceed the sum of the individual resistance element power rating in the network. 3.3.5 Operating voltage. Each resistor element shall have a maximum operating volta
16、ge of 100 V dc or ac rms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 4 3.3.6 Schematic. Resistor networks are available in schematics listed on fi
17、gure 2. 3.3.7 Resistance temperature characteristic. Unless otherwise specified, the resistance temperature characteristic shall be 100 ppm/oC. 3.4 Characteristic. The characteristic shall be in accordance with MIL-PRF-83401, characteristic K. 3.5 Pure tin. The use of pure tin, as an underplate or f
18、inal finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.6 Environmental requirements. The environmental requirements shall be in accordanc
19、e with MIL-PRF-83401, characteristic K. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, o
20、r environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Certificate of compliance. A certificate of compliance shall be
21、required from manufacturers requesting to be listed as a suggested source of supply. 3.10 Workmanship. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not a
22、pplicable to this document. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections of MIL-PRF-83401. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of complia
23、nce with group B requirements in lieu of performing group B tests (see 6.2d). 4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-83401. 4.4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physica
24、l dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-83401. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD
25、or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military s
26、ervices system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
27、se from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 5 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC. 3. Power rating shall be 25 mW at +120oC. 4. k = kilohms. NOTES: 1. Resista
28、nce tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R1 and R5 power rating shall be 60 mW at +120oC. R2, R3, R4, R6, R7 and R8 power ratings shall be 25 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance.Provided by I
29、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 6 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum
30、. 3. R1 and R6 power rating shall be 60 mW at +120oC. R2, R3, R4, R5, R7, R8 and R9 power ratings shall be 25 mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R3 and R6 power rating shall be 6
31、0 mW at +120oC. R1, R2, R4, R5, and R7 power ratings shall be 25 mW at +120oC. 4. = ohms, k = kilohms FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON,
32、OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 7 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC. 3. Power rating shall be 25 mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor tem
33、perature coefficient shall be 200 ppm/oC. 3. Power rating shall be 25 mW at +120oC. 4. = ohms, k = kilohms FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAY
34、TON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 8 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC. 3. Power rating shall be 25 mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 1 percent. 2. Resisto
35、r temperature coefficient shall be 100 ppm/oC maximum. 3. k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 1493
36、3 DWG NO. 87072 REV D PAGE 9 NOTES: 1. Resistance tolerance shall be 5 percent. NOTES: 1. Resistance tolerance shall be 1percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum; except R4 which shall be 100 ppm/oC maximum. 3. k = kilohms. FIGURE 2. Schematic, resistance and toleranc
37、e - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 10 NOTES: 1. Resistance tolerance shall be 1 percent. 2. Resistor temperature coefficien
38、t shall be 100 ppm/oC maximum. 3. k = kilohms. NOTES: 1. Resistance tolerance shall be 5 percent. 2. k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CEN
39、TER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87072 REV D PAGE 11 NOTES: 1. Resistance tolerance shall be 1 percent. 2. Resistor temperature coefficient shall be 100 ppm/oC maximum. 3. k = kilohms. NOTES: 1. Resistance tolerance shall be 5 percent. 2. Resistor temperature coefficient shall be
40、 200 ppm/oC maximum. 3. Power rating shall be 20 mW per resistor 4. k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDEN
41、T NO. 14933 DWG NO. 87072 REV D PAGE 12 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistor networks are used in surface mounting applications where space is a major concern. 6.2 Ordering data. The cont
42、ract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, and one copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements
43、for packaging and packing. (i.e. ESD sensitive packaging). d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. 6.3 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by ele
44、ctrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 which specifies a preventive packaging procedure. 6.4 Tin whisker growth. The use of alloys with tin content
45、greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-
46、prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 User of record. Coordina
47、tion of this document for future revisions is coordinated only with the suggested source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, O
48、H 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.6 Suggested source of supply. Suggested source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN Vendor similar designation or type num
