1、 REVISION SLT DESCRIPTION DATE APPROVED A Deleted all references to military standards. Editorial changes throughout. 18 May 90 David E. Moore B Updated suggested source of supply. Editorial changes throughout. 28 June 00 James A. Crum C Updated suggested source of supply. Updated manufacturers part
2、 numbers. Corrected error in Table ll. Editorial changes throughout. 18 April 2006 Michael A. Radecki Prepared in accordance with ASME Y14.100 Selected item drawingREV STATUS OF PAGES REV C C C C C C PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY ROBERT E. GRILLOT DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY
3、CENTER, DAYTON, OH 45444-5000 Original date of drawing 20 MARCH 1989 CHECKED BY PATRICK G. KYNE TITLE CAPACITORS, FIXED, PAPER (OR PAPER-PLASTIC) DIELECTRIC APPROVED BY EDWARD H. BACK SIZE A CODE IDENT. NO. 14933 DWG NO. 88028 REV C PAGE 1 OF 6 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTI
4、CS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 AMSC N/A 5910-E359 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88028 REV C PAGE 2 1.
5、SCOPE 1.1 Scope. This drawing describes the requirements for paper (or paper-plastic) dielectric capacitors. 1.2 Part or Identifying Number (PIN) The complete PIN is as follows: 88028 -XX Drawing number Dash number (see table I) 2. APPLICABLE DOCUMENTS This section is not applicable to this drawing.
6、 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1 and table I). 3.1.1 Termination blades. See figure 1. 3.1.2 Case material. Aluminum. 3.1.3 Operating temperature range. The operating temperature range shall be -4
7、0C to +75C. 3.1.4 Storage temperature. -55C to +90C. 3.2 Electrical characteristics. The electrical characteristics shall be as follows. 3.2.1 Dielectric type. Paper or paper-plastic. 3.2.2 Rated voltage. See table I. 3.2.3 Ripple voltage. The ripple voltage should not exceed the following percentag
8、es of the rated voltage for these frequencies: Frequency Percent of rated voltage60 Hz 30 120 Hz 20 400 Hz 14 1,000 Hz 8 10,000 Hz 1 3.2.4 Capacitance (+25C). When capacitors are tested in accordance with 4.1.3, the capacitance value shall be in accordance with table I. 3.2.5 Dissipation factor (+25
9、C). When capacitors are tested in accordance with 4.1.4, the dissipation factor shall be in accordance with table I. 3.2.6 Capacitance tolerance. 10 percent. 3.2.7 Capacitance variation with temperature. 5 percent over range -40C to +75C. 3.2.8 Operating life. 60,000 hours with 94 percent survival.
10、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Inches mm .03 0.8 .06 1.5 .12 3.0 .52 13.2 .75 19.0 .81 20.6 1.31 33.3 1.91 48.5 1.97 50.0 2.16 54.9 2.91 73.9 3.66 93.0 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 1
11、4933 DWG NO. 88028 REV C PAGE 3 Dimensions Case style A D A 2.16 1.31C 2.91 1.91 D 3.66 1.97NOTES: 1. Dimensions are in inches (see figure 1 and table I). 2. Metric equivalents are given for general information only. FIGURE 1. Case dimensions and configuration. Provided by IHSNot for ResaleNo reprod
12、uction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88028 REV C PAGE 4 3.3 Marking. Marking shall be as specified in 1.2 with the manufacturers name or CAGE code. 3.4 Recycled, recovered, or environ
13、mentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.5 Certificate
14、 of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.6 Workmanship. Capacitors shall be free of burrs and sharp edges (see 4.1.2). 4. VERIFICATION 4.1 Conformance inspection. 4.1.1 Inspection of product for delivery. Inspec
15、tion of product for delivery shall consist of the group A inspection. 4.1.1.1 Group A inspection. Group A inspection shall consist of the inspections specified in table II in the order shown. 4.1.2 Criteria for defectives. All dimensional characteristics are considered defective when out of toleranc
16、e. All physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. All workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival. 4.
17、1.3 Capacitance (see 3.2.4). Unmounted capacitors shall be tested as follows: a. Test frequency: 60 Hz 10 Hz. b. Test voltage: 50 - 70 volts rms. 4.1.4 Dissipation factor (see 3.2.5). Dissipation factor shall be measured with a bridge or other suitable equipment at the frequency and voltage specifie
18、d in 4.1.3. The capacitors shall be unmounted. TABLE I. Electrical characteristics. Case height “C” DSCC drawing 88028- Capacitance F Volts peak dc Dissipation factor Case style Inches mm 01 1.00 2000 .3% maximum A 3.12 79.25 02 2.00 2000 .3% maximum A 3.88 98.60 03 3.00 2000 .3% maximum C 3.12 79.2
19、5 04 4.00 2000 .3% maximum C 3.50 88.90 05 5.00 2000 .3% maximum C 4.25 107.95 06 6.00 2000 .3% maximum C 4.75 120.70 07 8.00 2000 .3% maximum D 4.75 120.70 08 10.00 2000 .3% maximum D 5.75 146.05 09 0.10 2500 .3% maximum A 2.12 53.85 10 0.25 2500 .3% maximum A 2.12 53.85 11 0.50 2500 .3% maximum A
20、2.12 53.85 12 1.00 2500 .3% maximum A 3.12 66.55 13 2.00 2500 .3% maximum A 4.25 107.95 14 4.00 2500 .3% maximum C 4.25 107.95 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT
21、 NO. 14933 DWG NO. 88028 REV C PAGE 5 TABLE II. Group A inspection. Inspection Requirement paragraph Test method paragraph Lot criteria Capacitance 3.2.4 4.1.3 100 percent inspection Visual and mechanical inspections Material 3.1.2 Workmanship 3.6 4.1.2 100 percent inspection Dimensions 3.1 4.1.2 10
22、0 percent inspection 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packa
23、ging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Milita
24、ry Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to th
25、is drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings,
26、 and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN
27、 (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing (see 5.1). 6.3 Replaceability. Capacitors cove
28、red by this drawing will replace the same commercial device covered by a contractor-prepared specification or drawing. 6.4 Users of record. Coordination of this document for future revisions is coordinated only with the suggested sources of supply and the users of record of this document. Requests t
29、o be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus (DSCC), ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. 6.5 Suggested sources of supply. Suggeste
30、d sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil, or by telephone (6
31、14) 692-4709 or DSN 850-4709. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88028 REV C PAGE 6 DSCC drawing 88028- Vendor Similar Designation or Type Numb
32、er 1/ Vendor CAGE Vendor Name and Address 01 02 03 04 05 06 07 08 09 10 11 12 13 14 A26F7575 A26F7508 A26F7509 A26F7510 A26F7511 A26F7512 A26F7513 A26F7514 A26F7515 A26F7516 A26F7517 A26F7576 A26F7519 A26F7520 01002 GE Capacitor & Power Quality Products 381 Broadway Fort Edward, NY 12828-1000 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
