1、REVISIONS LTR DESCRIPTION DATE APPROVED A Delete “part number“ and substitute “Part or Identifying Number (PIN)”. Vendor CAGE 60563, PINs, delete and substitute new PINs. Editorial changes throughout. 01-01-22 Robert M. Heber B Add Vendor CAGE SW884, delete MIL-STD-1344 test methods, add EIA-364 tes
2、t procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV B A A B B REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ralph Antonelli DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Charles W. Koeller C
3、ONNECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, TWENTY FIVE SIZE 20 SIGNAL CONTACTS, WITH TWO SIZE 8 CONTACT CAVITIES SIZE CAGE CODE 037Z3 DWG. NO.89081 Original date of drawing 31 July 1990 A REV B PAGE 1 OF 5 AMSC N/A 5935-E776-000 Provided by IHSNot for ResaleNo reproduction or networking pe
4、rmitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm Inches mm .055 .056 .109 .112 .163 .218 .272 1.40 1.42 2.77 2.84 4.14 5.54 6.41 .326 .381 .435 .489 .544 .598 .652 8.28 9.68 11.05 12.42 13.81 15.19 16.56 NOTES: 1. Dimensions are in inches. 2. Metric equivalen
5、ts are given for information only. 3. Unless otherwise specified, tolerance for three place decimals is .005 inch (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a .005 inch (0.13 mm) diameter circle. 6. Markings are shown for the pin ins
6、ert front. Socket inserts are the opposite. 7. Reference documents shall be of the issue in effect on date of invitations for bid. 037Z3 89081 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE2 FIGURE 1. Insert arrangement, twenty five size 20 signal contacts, with two size 8 conta
7、ct cavities. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C to +125C. REQUIREMENTS: Requirements of drawing 85039 and MIL-DTL-24308 are
8、applicable. Dimensions and configurations: See figure 1. Signal contact specifications: Style A (crimp removable signal contacts): Socket: M39029/63-368. Pin: M39029/64-369. Style B (solder fixed signal contacts): Socket: MIL-DTL-24308, Appendix B, figure B-1. Pin: MIL-DTL-24308, Appendix B, figure
9、B-2. Shell size: Four. Shell specifications: Style A: Socket: MIL-DTL-24308/2, figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be designated for contact insertion and re
10、moval with the applicable military tool as follows: Contact size Tool PIN20 M81969/39 - 01 with plastic tip M81969/1-02 with metal tip 037Z3 89081 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license
11、 from IHS-,-,-SIZE CAGE CODE DWG NO. Mating and unmating forces (with signal contacts only installed): See table I. TABLE I. Mating and unmating forces. Mating force (pounds) Unmating force (pounds) Contact type Minimum Maximum Minimum Maximum Signal 0.962 28.0 0.962 17.0 Contact resistance: See tab
12、le II. TABLE II. Contact resistance (millivolts maximum). 1/ Contact classes G, D, M, N Contact Size AWG wire Size Test current (amperes) After salt spray All others 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstanding voltage: See table III. TABLE II
13、I. Dielectric withstanding voltage. Altitude Humidity condition All other conditions Sea level 600 1,000 70,000 - 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature shall be -55C to +125C. 037Z3 89081 D
14、EFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Approved sources of supply are listed herein. Additional sources will be added as they become available. The ve
15、ndors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 60563 CAGE 28198 SW884 89081GBEPT 89081GBEST 89081GBEPR 89081GBESR P272PSA2D P272RSA2D P272PSA2 P272RSA2 CBM27W
16、2M02F00C-0 CBM27W2F02F00C-0 CBM27W2M02000C-0 CBM27W2F02000C-0 PCMMH27W2P PCMMH27W2S PCMM27W2P PCMM27W2S 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall in
17、clude a full complement of signal contacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap-in and removable. 5/ For size 8 contacts, see DSCC drawings 89046 through 89061. Vender CAGE Vendor name number and address 28198 Positronics Industries, Incorporated 423 North Ca
18、mpbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 89081 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
