1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC N/A Jeffery Tunstall DEFENSE SUPPLY CENT
2、ER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Abdo Abdouni APPROVED BY Robert Heber CONNECTOR, ELECTRICAL, CIRCULAR, RECEPTACLE WALL MOUNTING FLANGE, REMOVABLE CRIMP CONTACTS, SERIES III, HYBRID CONSTRUCTION SIZE CAGE CODE 037Z3 DWG. NO. 89093 Original date of drawing 21 Sept 89 A REV A PA
3、GE 1 OF 6 AMSC N/A 5935-E664 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
4、HS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89093 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 3 FIGURE 1. Receptacle, wall mounting. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89093 DEFENSE SUPPLY CE
5、NTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 4 Shell size Shell size code P dia R1 (see note 4) S V W Z 9 A .136 .120 .719 .949 .925 .823 .098 .083 1.240 11 B .136 .120 .812 1.043 1.020 .823 .098 .083 1.240 13 C .136 .129 .906 1.138 1.114 .823 .098 .083 1.240 15 D .136 .120 .969 1.232 1.209 .
6、823 .098 .083 1.240 17 E .136 .120 1.062 1.323 1.299 .823 .098 .083 1.240 19 F .136 .120 1.156 1.449 1.425 .823 .098 .083 1.240 21 G .136 .120 1.250 1.575 1.551 .823 .098 .083 1.240 23 H .162 .146 1.375 1.701 1.677 .823 .098 .083 1.240 25 J .162 .146 1.500 1.823 1.799 .823 098 .083 1.240 Inches mm I
7、nches mm Inches mm Inches mm .060 1.52 .719 18.26 1.062 26.97 1.375 34.92 .070 1.78 .791 20.09 1.114 28.30 1.425 36.20 .083 2.11 .812 20.62 1.138 28.91 1.449 36.80 .098 2.48 .823 20.90 1.156 29.36 1.500 38.10 .120 3.05 .906 23.01 1.209 30.71 1.551 39.40 .126 3.20 .925 23.50 1.232 31.29 1.575 40.00 .
8、136 3.45 .949 24.10 1.240 31.50 1.677 42.60 .146 3.71 .969 24.61 1.250 31.75 1.701 43.21 .162 13.21 1.020 25.91 1.299 32.99 1. 799 45.69 .520 13.21 1.043 26.49 1.323 33.60 1.823 46.30 NOTES: 1. Dimensions are inches. 2. Metric equivalents are given for general information only. 3. Metallic material
9、inner shell must have solid surface through the length Z and inner circumference of the shell. 4. Front and rear panel mount. Use type A for back panel mounting and type B for front panel mounting. See MIL-DTL-38999 for recommended panel dimensions. 5. For details of connector front and rear end con
10、figuration, see MIL-DTL-38999, series III. 6. Metallic surfaces required for conductivity between receptacle plug: receptacle rear accessories panel. FIGURE 1. Receptacle, wall mounting Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE
11、CAGE CODE DWG NO. 037Z3 89093 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 5 SCOPE This is an extended environment-resisting hybrid construction (metal sleeve in nonmetallic shell) connector. Metallic surfaces indicated on figure 1 are finished with olive drab cadmium plate o
12、ver a suitable underplate. Other Surfaces are uncoated nonmetallic for corrosion resistance. REQUIREMENTS: Connectors shall meet the requirements of MIL-DTL-38999, series III, class W, with the following exceptions and additions. Dimension and configurations: See figure 1. Interface dimensions shall
13、 confirm to MIL-DTL-38999. For insert arrangements: See MIL-STD-1560. Salt spray (corrosion): The wired, assembled connectors shall meet the dynamic salt spray requirements of MIL-DTL-38999, with the following exceptions: The connectors shall be tested 1052 hours mated, followed by 48 hours unmated.
14、 Hydorlytic stability: Unmated, unwired connectors shall be subjected to the following tests: a. Measure connector weight. b. Boil in distilled water until no further weight gain is observed. c. Connector may be dried with filtered compressed air. d. When connector weight has stabilized, measure per
15、cent total weight gain, mating dimensions and length. e. Mate the connector and apply specified coupling torque. f. Inspect the connectors for damage. The connector shall be without defects detrimental to mechanical performance. Total weight gain shall be less than 0.75 percent. When subjected to co
16、upling torque values specified in series III, coupling torque of MIL-DTL-38999, there shall be no evidence of cracking, breaking or loosening of parts. Lighting strike: Mated connectors with suitable accessories shall be subjected to a simulated lighting current pulse exposure. The current pulse sha
17、ll be applied by a suitable high current generator and the current waveform shall be monitored and recorded by a current transformers (or current shunt) and storage oscilloscope. The test pulse shall be a damped sinusoid with a basic frequency of 21 kHz and an amplitude decay time of 140 microsecond
18、s to 37 percent of its peak value. Pulse amplitude shall be 60 kA. The receptacle connector shall be mounted on a simulated panel, using its normal mounting provisions. The simulated current pulse shall be applied between the plug accessory and the receptacle mounting panel. Upon completion of the p
19、ulse application, and without disturbing the test sample, the shell-to-shell conductivity test of MIL-DTL-38999 shall be performed. When the test electrical measurements have been completed, the sample shall be inspected in both the mated and unmated condition for evidence of damage from the simulat
20、ed lighting current pulse. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89093 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 6 Part or Identifying Number (PIN): The following PIN shall be in accor
21、dance with the following: 89093- 11- 35 P N DSCC drawing number Shell size Insert arrangement Contact style Polarizing position Marking: Marking shall be accordance with MIL-DTL-38999 except the PIN shall be as stated above. Application guidance: To obtain full extended performance as specified abov
22、e, this connector must be assembled with the applicable accessory backshell and mated with a hybrid counterpart receptacle. QUALIFICATION Qualification inspection: Qualification inspection for the connectors specified herein shall not be required. Quality conformance inspection: Shall be in accordan
23、ce with MIL-DTL-38999. Inspection of packaging: Shall be in accordance with MIL-DTL-38999. Method of inspection: Shall be in accordance with MIL-DTL-38999. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89093 DEFENSE SUP
24、PLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 7 Approved sources of supply. Approved sources are listed herein. Additional sources will be added as they become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI.
25、 DSCC drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ Replacement military specification PIN 89093 64600 G300P* N/A 1/ Parts must be purchased to this DSCC Pin to assure that all performance requirements and tests are met. 2/ Do not use this number for item acquisition. Items acquired to this may not satisfy the performance requirements of this drawing. Vendor CAGE Vendor name number and address 64600 G & H Technology 740 West Ventura Boulevard Camarillo, CA 93010 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
