1、 REVISIONS LT DESCRIPTION DATE APPROVED A Changes in accordance with NOR 5905-R008-94. 8 Sep 1994 D. Moore B Changes in accordance with NOR 5905-R011-95. 30 Oct 1995 D. Moore C Changes to paragraphs 3.3.2, 3.3.3, 3.3.10, and 4.8. Deleted paragraph 3.3.6 Voltage rating. Editorial changes throughout.
2、8 Jul 1997 D. Moore D Changes in accordance with NOR 5905-R003-98. 3 Apr 1998 D. Moore E Update and validation of drawing. Editorial changes throughout. 3 Dec 2003 K. Cottongim F Add thermoplastic encapsulation. Add pure tin prohibition paragraph. Editorial changes throughout. 30 Oct 2006 M. Radecki
3、 G The epoxy encapsulation is obsolete and is superseded by thermoplastic encapsulation with cap to lead frame. Editorial changes throughout. 14 Apr 2010 M. Radecki Epoxy encapsulation is obsolete and is superseded by thermoplastic encapsulation with cap to lead frame CURRENT DESIGN ACTIVITY CAGE CO
4、DE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with AMSE Y14.100 Source control drawing REV STATUS REV G G G G G G OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY HERALDINE JOHNSON DEDIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER D
5、AYTON, OHIO 45444-5000 Original date of drawing 11 July 1994 CHECKED BY ANDREW ERNST TITLE RESISTOR, FIXED, WIREWOUND, SURFACE MOUNT, POWER TYPE (2 WATT) APPROVED BY DAVID E. MOORE SIZE A CODE IDENT. NO. 14933 DWG NO. 93077 REV G PAGE 1 OF 6 AMSC N/A 5905-E737 Provided by IHSNot for ResaleNo reprodu
6、ction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO: 93077 REV G PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 2 watt, fixed, surface mounted, wirewound, power type resistor. 1.2 Part o
7、r Identifying Number (PIN). The complete PIN is as follows: 93077 * * * I I I I I I I I Drawing Resistance value Tolerance Encapsulation number (see 3.3.1, 3.3.2) (see 3.3.3) (see 3.3.4) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following s
8、pecifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39007 - Resistors, Fixed, Wirewound (Power Type
9、), Nonestablished Reliability, Established Reliability, and Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-690 - Failure Rate Sampling Plans and Procedures. MIL-STD-790 - Established Reliabilit
10、y and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. MIL-STD-1285 - Marking of Electrical and Electronic Parts. * (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardi
11、zation Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of t
12、his document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-39007 and as specified herein. 3.2 I
13、nterface and physical dimensions. Resistors shall meet the interface and physical dimensions as specified in MIL-PRF-39007 and herein (see figure 1). 3.3 Electrical characteristics. 3.3.1 Resistance value designation. Resistance value designations shall be in accordance with MIL-PRF-39007. 3.3.2 Res
14、istance. The resistance range shall be .1 ohm to 4.92 kilohms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO: 93077 REV G PAGE 3 Dimensions A B C D E F G (11.0 .127) .
15、433 .005 (11.30 .813) .445 .032 (2.54 .254) .100 .010 (4.11 .381) .162 .015 (3.96 .127) .156 .005 (6.98 .127) .275 .005 (5.46 .127) .215 .005 NOTES: 1. Dimensions are in inches, millimeters are in parentheses. 2. Inch equivalents are given for general information only. FIGURE 1. Resistor, fixed, wir
16、ewound, surface mount. 3.3.3 Resistance tolerance. Resistance tolerances are available in (D) 0.5 percent (for values above 1 ohm), (F) 1 percent, (H) 3 percent, and (J) 5 percent. * 3.3.4 Encapsulation. The encapsulation shall be in accordance with table I. TABLE I. Encapsulation. Style Encapsulati
17、on (blank) 1/ A Thermoplastic with cap to lead frame Thermoplastic with lead to lead frame 3.3.5 Power rating. The power rating shall be 2 watt at +70C. For operation at temperatures greater than +70C, derate in accordance with figure 2. * 3.3.6 Resistance temperature coefficient. The resistance tem
18、perature coefficient shall be as follows: Style (blank) (cap to lead frame) encapsulation Style A (lead to lead frame) encapsulation 0.1 ohm to 0.99 ohm-90 ppm/C 0.1 ohm to 0.3 ohm-150 ppm/C 1.0 ohm to 9.9 ohm-50 ppm/C 0.31 ohm to 0.99 ohm-90 ppm/C 10 ohms and over -20 ppm/C 1.0 ohm to 9.9 ohm-50 pp
19、m/C 10 ohms and over -20 ppm/C 3.3.7 Thermal shock. When resistors are tested as specified in 4.6, there shall be no evidence of mechanical damage. The maximum change in resistance shall not exceed (0.2 percent +0.05 ohm). 3.3.8 Load life. When resistors are tested as specified in 4.7, there shall b
20、e no evidence of mechanical damage. The maximum change in resistance shall not exceed (0.5 percent +0.05 ohm). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO: 93077 REV
21、 G PAGE 4 * FIGURE 2. Derating curves for high ambient temperatures. 3.3.9 Overload. When resistors are tested as specified in 4.8, there shall be no evidence of electrical or mechanical damage. The maximum change in resistance shall not exceed (0.2 percent + 0.005 ohm). 3.3.10 Solderability. The to
22、tal surface area of the dipped part of the termination is at least 95 percent covered by a continuous new solder coating. Pin holes, voids, porosity, nonwetting, or dewetting shall not be concentrated in one area and shall not exceed 5 percent of the total termination area. The area of the surface t
23、o be tested shall include the total metallized areas of both terminations within .3125 inch (7.938 mm) of the bottom contact point of the “J“ bend. In case of a dispute, the percentage of coverage with pinholes or voids shall be determined by actual measurement of these areas, as compared to the tot
24、al area. 3.3.11 High temperature exposure. When resistors are tested as specified in 4.10, there shall be no evidence of mechanical damage. The maximum change in resistance shall not exceed (0.5 percent +0.05 ohm). 3.4 Marking. Marking shall be as shown: 93077 (DSCC drawing number) 1R00FA (resistanc
25、e value, tolerance, and encapsulation) XXXXX (CAGE code) 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 perc
26、ent lead, by mass (see 6.3). 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and prom
27、otes economically advantageous life cycle costs. * 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-39007 Qualified Products List for at least one part, or perform the group A and group B inspections specified her
28、ein on a sample agreed upon by the manufacturer and DSCC-VA. * 3.7.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply (see 6.2d). Provided by IHSNot for ResaleNo reproduction or networking permitted wi
29、thout license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO: 93077 REV G PAGE 5 3.8 Workmanship. The resistor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification
30、inspection. Qualification inspection is not applicable to this document. 4.2 Reliability assurance program. The reliability assurance program specified in MIL-PRF-39007 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.3 Failure rate qualification. Failure rate qual
31、ification specified in MIL-PRF-39007 and MIL-STD-690 is not applicable to this document. 4.4 Conformance inspection. Conformance inspection shall consist of group A (ER level) and group B inspections of MIL-PRF-39007. Group A, subgroup 1 conditioning will not be performed. 4.4.1 Certification. The a
32、ctivity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.5 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-39007. 4.6 Thermal shock. Resistors shall be tested in accordance with
33、 MIL-PRF-39007 and the following exception shall apply: Mounting of test samples shall be on surface mount test cards, and Method 107 of MIL-STD-202, test condition B-3. 4.7 Load life. Resistors shall be tested in accordance with MIL-PRF-39007 and the following exception shall apply: Mounting of tes
34、t samples shall be on surface mount test cards, and 1,000 hours at maximum load at +25C. 4.8 Overload. Resistors shall be tested in accordance with MIL-PRF-39007 and the following exception shall apply: Mounting of test samples shall be on surface mount test cards, and Overload testing will be perfo
35、rmed at 5 times rated power for 5 seconds. 4.9 Solderability. Solderability shall be in accordance with method 208 of MIL-STD-202 and the following details shall apply: a. Application of flux: Type R shall be used. Terminations shall be immersed in the flux, which is at room temperature, to the mini
36、mum depth necessary to cover the surface to be tested. The terminations shall be completely immersed by individually dipping each termination. The terminations to be tested shall be immersed in the flux for a period of 5 seconds to 10 seconds. b. Solder dip: The dross and burned flux shall be skimme
37、d from the surface of the molten solder (may not require separate operation in wave or flow pot). The molten solder shall be maintained at a uniform temperature of +245C 5C. The surface of the molten solder shall be skimmed again prior to immersing the terminations in the solder. The part shall be a
38、ttached to a dipping device and the flux-covered terminations immersed in molten solder to the depth, and in the same manner specified in 4.9a. After the dipping process, the part shall be allowed to cool in air. Residue flux shall be removed from the terminations by rinsing in a suitable solvent. I
39、f necessary, a soft cloth or cotton swab moistened with clean 91 percent isopropyl alcohol shall remove all remaining flux. c. Examination of terminations: After each dip-coated termination has been thoroughly cleaned of flux, the terminations shall be examined under a magnification between 10X and
40、20X. 4.10 High temperature exposure. Resistors shall be tested in accordance with MIL-PRF-39007 and the following exception shall apply: Mounting of test samples shall be on surface mount test cards, and 250 hours at +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without
41、 license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO: 93077 REV G PAGE 6 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be pe
42、rformed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or withi
43、n the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explan
44、atory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Surface mount resistors are used in electronic circuits where space is a major concern. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery:
45、One copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of com
46、pliance with group B requirements (see 4.4.1). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical op
47、erating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refe
48、r to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). * 6.4 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.5 Approved source of supply. Approved source of supply is listed he
